Air Shot Blast 작업실 내부 환기 시스템 개선에 관한 수치해석

진도훈,Chin, Do-Hun 한국산업융합학회 2022 한국산업융합학회 논문집 Vol.25 No.5

The purpose of this study is to design an effective atmospheric environment system through the design of the dust collection in the air shot room being operated in a domestic shipyard. The ventilation system in the current air shot room mostly uses a dust collecting filter to filter internal particles and releases them in the atmosphere. A conventional design was made too much. In order to prevent an error and draw an optimal design, Computational fluid dynamics (CFD) tried to be applied only to air shot room. In the advanced design technique, computer simulation was conducted to secure basic design data. In order to find the basic design of the ventilation system and the flow field in the air shot room at propeller mold workplace of a shipyard, the CFD was conducted. In the case of Model-1 as a conventional workplace, where air flows in the inlet due to the subatmospheric pressure generated by inhalation of an air blower and flows out to the outlet, a discharge flow rate was somewhat low, and there was the holdup zone in the room. In the case of Model-2 as an improved model, the ventilation system was improved in the Push-Pull type, and the holdup of the internal flow field was improved.

Rockwell Hardness Modeling Using Volumetric Variable

진도훈,오상록,윤문철 한국생산제조학회 2013 한국생산제조학회지 Vol.22 No.3

A new Rockwell hardness (HRC) model using a volumetric parameter by a least square and fractal interpolation method is suggested. The results are also investigated in comparison to real measured hardness data. For this purpose, the measurement of an indented volume is performed using a confocal laser scanning microscope (CLSM), and the captured height encoded image (HEI) is used as an original surface for the calculation of the indented volume. After configuring the surface, the constructed volume is calculated and used as an independent variable for HRC hardness modeling. The hardness model is established using an experimental modeling technique involving a least square algorithm and fractal interpolating model, and this suggested model can be used to reliably predict the Rockwell hardness. These techniques can also be applied to the modeling of the Brinnell and Vickers hardnesses using a volumetric variable.

극저온용 액중펌프 구조해석에 관한 연구

진도훈,이중섭 한국산업융합학회 2020 한국산업융합학회 논문집 Vol.23 No.5

Recently, reciprocating cryogenic pumps are mainly developed for small-and-mid sized fuel supply systems. Centrifugal type pumps are not actively developed. Most cryogenic submerged pumps are imported. For transportation, cryogenic liquefied natural gas requires the liquid pump technology that can works in extreme evironments. In order to transport liquefied natural gas, it is necessary to apply pump technology. This is the fundamental research for developing the submerged pump technology applicable to the transportation and storage system equipment of cryogenic liquefied system. It tries to secure basic design materials through reverse-engineering in the cryogenic submerged pump development. Regarding materials, STS-304 and STS-431 which are stainless materials widely used in the cryogenic area are applied. Aluminum alloy is applied to impeller and upper manifolder and the pump rotates at the high speed of 6,000rpm.

Lubrication Behavior of Slider Bearing with Square Pocket Surface

진도훈,김광희,윤문철,Chin, Do-Hun,Kim, Kwang-Heui,Yoon, Moon-Chul The Korean Society of Manufacturing Process Engine 2017 한국기계가공학회지 Vol.16 No.5

In this paper, the characteristics and load carrying capacity of square pocket surfaces on a slider bearing are discussed for the thin film effect by the square pocket slider bearing. To study the lubrication, a Reynolds equation is used in this paper for the analysis of the slider bearing characteristics with square pocket surfaces. For numerical analysis, the central differencing scheme finite difference method is used. In a slider bearing with square pocket surfaces, the simulation dependent parameters such as pressure and load carrying capacity of the bearing can be acquired from the independent parameters, the slope of the slider bearing and number of pockets on the upper slider. These results can be acquired by the programmed softwar,e and they can be analyzed and stored in a sequential data file for later analysis. Furthermore, their pressure and load capacity distribution can be displayed easily by using the developed program with the Matlab GUI.

원자력 발전소에서 쓰나미 방지용 댐퍼 개발을 위한 유동해석

진도훈,Chin, Do-Hun 한국산업융합학회 2021 한국산업융합학회 논문집 Vol.24 No.1

The purpose of this study is to develop a damper that protects against the dangers of tidal waves since there's no function to block the inflow of large amounts of water into the inside When natural disasters such as tidal waves occur. Therefore, it intended to derive the design data by simulating through flow analysis in order to predict the pressure that a damper configured to open and close manually or automatically receives. It examined the preceding researches first and conducted the flow analysis, to predict the force of the damper installed on the bottom of the building's outside to prevent the inflow of seawater into the inside when natural disaster occurring. As a result, it showed that, in the event of a tsunami, it moved about 170m and the time impacting the damper occurred within about eight seconds, and, at the moment, the damper door was pressured about 17bar. Also, it could identify that the load was approximately 900kN and the force by the fluid was applied to the damper door.

아연도금 부스 환기시스템 개선에 관한 수치해석

진도훈,Chin, Do-Hun 한국산업융합학회 2021 한국산업융합학회 논문집 Vol.24 No.1

The purpose of this study is to suggest the optimal shape for a local air ventilation system for fume removal, which is operated in a zinc galvanizing factory, and to propose the improvement plan for a ventilation system used in a zinc galvanizing factory through flow analysis. A part of the air sprayed by an air curtain goes out. It will be necessary to research the position of an air curtain, its spray angles, and its nozzle shape. In addition, additional research needs to be conducted on the shape of the fan installed before a hood in order to make it easy to induce fume. In a local air ventilation system, air is inhaled from the outside. The higher an inlet negative pressure is, the easier fume is removed. It was found that it was necessary to install an appropriate hole in the wall on the back of a push nozzle in order to reduce an inlet negative pressure.

대형 선박 프로펠러 가공 공정용 터닝 시스템에 관한 연구

진도훈 한국산업융합학회 2023 한국산업융합학회 논문집 Vol.26 No.5

The propellers used for big ships have a large diameter and are very heavy. In order to apply a precise and safe work process to them, it is necessary to use an exclusive turning system. For this reason, various techniques are applied to produce them. However, workers’ convenience and safety are not taken into consideration enough at production sites. Conventionally, these propellers are designed to be separated as their turning system is loaded and rotated by empty weight. Therefore, it is necessary to replace such a design. This study tries to find the weaknesses of the design and structure of a conventional propeller turning system for large ships, to verify structure integrity of a structure in structural analysis, and to devise a plan for designing a new type of turning system. In the basic concept design and structural analysis for the turning system used in the propeller finishing process for large ships, this study drew the following conclusions. It was possible to develop the work process of the turning system for the propeller finishing process used for large ships, to obtain the dimensions for exterior design through a basic design. Structural analysis was conducted to find the structure integrity of the turning system. As a result, in the rail installed to transfer a gantry, the maximum stress was about 45MPa, about 5.5 times lower than the yield strength 250MPa. Therefore, the turning system was judged to be safe structurally.

원자력 발전소에서 쓰나미 방지용 댐퍼에 대한 구조해석

진도훈 한국산업융합학회 2020 한국산업융합학회 논문집 Vol.23 No.4

The purpose of this study is to research dampers, which are applied mainly to buildings adjacent to the coast, such as nuclear facilities, and used for ventilation and can safely protect lives and equipment in emergency situations. Comparing the equivalent stress for three models with hinge reinforcement and support reinforcement based on the early design model for Damper, in the Base model, the highest stress occurred in the part of hinge, especially in the centrally mounted hinge, and after reinforced the hinge, it was occurred in the rear support. For models reinforced hinges and supports, it is considered that reinforcement for stiffness will be required in the future as it entered within the range of allowable stress. For the safety factor distribution, the minimum safety ratio was sufficiently secured at least 1 and was high at the edge of the Damper frame and the Blade. As the hinge was reinforced, the safety factor distribution of Blade was increased, and it was verified that the safety factor was secured through the support reinforcement.

FMEA를 이용한 기계류 시스템의 신뢰도 분석

진도훈,우태수,이치우 한국공작기계학회 2002 한국공작기계학회 추계학술대회논문집 Vol.2002 No.-

This paper dealt with FMEA, which is a method of the analysis to secure safety and confidence coming up to customers' expectation in consideration of the environment of the corporation, the industrial environment, and the functional improvement. And by using FMEA, We showed the example analyzed the confidence of the Air Supply System. It was proved by the result of the analysis that the rate of the breakdown which is usually regarded as the first important point to reform can't satisfy the selecting basis to improve. Also the result said that it is not right to depend on only the rate of the failure in making the list of the reform. Through the analysis of the breakdown, FMEA can present the important factors of the reform to improve the confidence of the system. In this study would show the important factors of the improvement in order to product the goods guaranteed confidence through the method of FMEA.

축상유입식 사이클론 집진기 성능시험에 관한 연구

진도훈 한국산업융합학회 2020 한국산업융합학회 논문집 Vol.23 No.1

Along with dust collection efficiency, pressure loss is a very important cyclone operation factor. A severe rise in pressure loss causes the problem of cost. To solve the problem, the method connecting axial-vane type cyclones in parallel is suggested recently. The axial vane type cyclone dust collector applied in this study is a small portable type. Multiple cyclones are installed in a round type. The basic performance test on the axial vane type cyclone dust collector was conducted. As a result, the cut size reduced along with a rise in the wind velocity of the cyclone dust collector inlet. According to the test on dust collection efficiency, the effect of dust collection began to appear in the range of 3㎛ and dust collection efficiency was greatly improved at 5 ㎛. The noise of the cyclone dust collector well met the fan sound power level of KSB 6361.