Effect of Shrinkage Restraint on Deflections of Reinforced Self-compacting Concrete Beams

Ilker Kalkan,이종한 대한토목학회 2013 KSCE JOURNAL OF CIVIL ENGINEERING Vol.17 No.7

This paper presents the results of a study aimed at investigating the effects of restrained shrinkage on the in-plane deflection behavior of reinforced beams cast with self-compacting concrete. The load-deflection data from the tests on two sets of heavilyreinforced concrete beams were analyzed. The first set of beams was made with self-compacting concrete while conventionally vibrated concrete with shrinkage reducing admixture was used in the second set. It was found out that the first set underwent shrinkage cracking at early ages and this cracking caused the member responses of the beams to be closer to the fully-cracked response at the initial stages of loading. The second set of beams was found to have initial responses approximate to the uncracked response and the maximum shrinkage restraint stresses were calculated to be in the order of 20-40% of the modulus of rupture of concrete. The maximum shrinkage-induced restraint stress expressions of the AS 3600-2001, AS 3600-2009, EC2, and CSA A23.3-04 codes were found to underestimate the restraint stresses developed in the first set, yet the estimates from code solutions were in closer agreement with the experimental values in the second set.

Deflections of reinforced concrete beams with transverse openings of different geometries

Ilker Kalkan,Ece Ceylan,Saruhan Kartal,Mehmet Baran 국제구조공학회 2021 Structural Engineering and Mechanics, An Int'l Jou Vol.80 No.3

The present study pertains to the in-plane bending deflections of reinforced concrete beams with multiple regular transverse openings along the beam length. The total deflections in the beam were obtained from bending deflections and the additional deflections from the Vierendeel panel action. The accuracy of the deflection estimates from the proposed formula were observed to depend on the opening geometry. Among different geometries, the presence of rectangular and parallelogram web openings resulted in the experimental deflections to deviate more considerably from the analytical values due to the stress concentrations around the corners of the openings. Consequently, a multiplier was incorporated into the deflection formula to account for the opening geometry. The new revised formula was found to generate analytical load-deflection curves in close agreement with the experimental ones and service-load deflections close to the FEA values of beams with varying amount of tension reinforcement. The diagonal reinforcement around the openings and the short stirrups in the posts and chords increased the accuracy of the analytical deflection estimates by reducing the undesired additional deformations in the beam due to the poorer integrity of the posts and chords around the openings.

Strengthening of reinforced concrete beams with epoxy-bonded perforated steel plates

Aykac, Sabahattin,Kalkan, Ilker,Uysal, Ali Techno-Press 2012 Structural Engineering and Mechanics, An Int'l Jou Vol.44 No.6

Although being one of the most popular strengthening techniques in reinforced concrete beams, the use of steel plates bonded to the soffit raises problems of ductility. This study aims at investigating the influence of the use of perforated steel plates instead of solid steel plates on the ductility of reinforced concrete beams. A total of nine reinforced concrete beams were tested. In addition to an unplated beam, eight beams with perforated steel plates of two different thicknesses (3 mm and 6 mm) were subjected to monotonic loading. Effect of bonding the plates to the beams with anchor bolts and with additional side plates bonded to the sides of the beam with and without anchors is also investigated. The use of bolts in addition to epoxy was found to greatly contribute to the ductility and energy absorption capacity of the beams, particularly in specimens with thick plates (6 mm) and the use side plates in addition to the bottom plate was found to be ineffective in increasing the ductility of a concrete beam unless the side plates are attached to the beam with anchors bolts. The thickness of the plate was found to have little effect on the bending rigidity of the beam.

Strengthening of reinforced concrete beams with epoxy-bonded perforated steel plates

Sabahattin Aykac,Ilker Kalkan,Ali Uysal 국제구조공학회 2012 Structural Engineering and Mechanics, An Int'l Jou Vol.44 No.6

Although being one of the most popular strengthening techniques in reinforced concrete beams, the use of steel plates bonded to the soffit raises problems of ductility. This study aims at investigating the influence of the use of perforated steel plates instead of solid steel plates on the ductility of reinforced concrete beams. A total of nine reinforced concrete beams were tested. In addition to an unplated beam, eight beams with perforated steel plates of two different thicknesses (3 mm and 6 mm) were subjected to monotonic loading. Effect of bonding the plates to the beams with anchor bolts and with additional side plates bonded to the sides of the beam with and without anchors is also investigated. The use of bolts in addition to epoxy was found to greatly contribute to the ductility and energy absorption capacity of the beams, particularly in specimens with thick plates (6 mm) and the use side plates in addition to the bottom plate was found to be ineffective in increasing the ductility of a concrete beam unless the side plates are attached to the beam with anchors bolts. The thickness of the plate was found to have little effect on the bending rigidity of the beam.

The effects of vertical earthquake motion on an R/C structure

Selcuk Bas,Ilker Kalkan 국제구조공학회 2016 Structural Engineering and Mechanics, An Int'l Jou Vol.59 No.4

The present study investigated the earthquake behavior of R/C structures considering the vertical earthquake motion with the help of a comparative study. For this aim, the linear time-history analyses of a high-rise R/C structure designed according to TSC-2007 requirements were conducted including and excluding the vertical earthquake motion. Earthquake records used in the analyses were selected based on the ratio of vertical peak acceleration to horizontal peak acceleration (V/H). The frequency-domain analyses of the earthquake records were also performed to compare the dominant frequency of the records with that of the structure. Based on the results obtained from the time-history analyses under the earthquake loading with (H+V) and without the vertical earthquake motion (H), the value of the overturning moment and the top-story vertical displacement were found to relatively increase when considering the vertical earthquake motion. The base shear force was also affected by this motion; however, its increase was lower compared to the overturning moment and the top-story vertical displacement. The other two parameters, the top-story lateral displacement and the top-story rotation angle, barely changed under H and H+V loading cases. Modal damping ratios and their variations in horizontal and vertical directions were also estimated using response acceleration records. No significant change in the horizontal damping ratio was observed whereas the vertical modal damping ratio noticeably increased under H+V loading. The results obtained from this study indicate that the desired structural earthquake performance cannot be provided under H+V loading due to the excessive increase in the overturning moment, and that the vertical damping ratio should be estimated considering the vertical earthquake motion.

PVC and POM gripping mechanisms for tension testing of FRP bars

Bogachan Basaran,Harun Yaka,Ilker Kalkan 국제구조공학회 2021 Structural Engineering and Mechanics, An Int'l Jou Vol.77 No.1

The present study pertains to the introduction of two new types of grip adaptor for universal testing machines, namely Polyvinyl Chloride (PVC) and Polyoxymethylene (POM) grip adaptors, and their application to tension testing of FRP bars with different fiber and surface finish types. The tabs are connected to the FRP bar sample with the help of mechanical anchors, i.e. bolts. These new adaptors offer vital superiorities over the existing end tab designs (anchors with filling material or mechanical anchorage), including the reduction in the time and labor for production, reusability and the mild nature, i.e. low hardness of the tab material, which retards and even prevents peeling and crushing in the gripping regions of an FRP sample. The methods were successfully applied to FRP bars with different types of fiber (CFRP, GFRP and BFRP) and different types of surface texture (ribbed, wrapped, sand-coated and wound). The test results indicated that the both types of end caps prevented slip of the bar, crushing and peeling in the gripping zone. The mechanical properties from the material tests with the new caps were in perfect agreement with the ones from the material tests with steel tubular caps.

Rollover instability of precast girders subjected to wind load

Lee, Jong-Han,Kalkan, Ilker,Lee, Jong-Jae,Cheung, Jin-Hwan Thomas Telford Ltd. 2017 Magazine of concrete research Vol.69 No.2

프리캐스트 콘크리트 거더의 횡방향 안정성

이종한 ( Lee Jong-han ),( Ilker Kalkan ),( Kabuyaya Kghuta ) 한국구조물진단유지관리공학회 2013 한국구조물진단유지관리공학회 학술발표대회 논문집 Vol.17 No.2

Lateral torsional buckling of doubly-symmetric steel cellular I-Beams

Mehmet Fethi Ertenli,Erdal Erdal,Alper Buyukkaragoz,Ilker Kalkan,Ceyhun Aksoylu,Yasin Onuralp Özkılıç 국제구조공학회 2023 Steel and Composite Structures, An International J Vol.46 No.5

The absence of an important portion of the web plate in steel beams with multiple circular perforations, cellular beams, causes the web plate to undergo distortions prior to and during lateral torsional buckling (LTB). The conventional LTB equations in the codes and literature underestimate the buckling moments of cellular beams due to web distortions. The present study is an attempt to develop analytical methods for estimating the elastic buckling moments of cellular beams. The proposed methods rely on the reductions in the torsional and warping rigidities of the beams due to web distortions and the reductions in the weak-axis bending and torsional rigidities due to the presence of web openings. To test the accuracy of the analytical estimates from proposed solutions, a total of 114 finite element analyses were conducted for six different standard IPEO sections and varying unbraced lengths within the elastic limits. These analyses clearly indicated that the LTB solutions in the AISC 360- 16 and AS4100:2020 codes overestimate the buckling loads of cellular beams within elastic limits, particularly at shorter span lengths. The LDB solutions in the literature and the Eurocode 3 LTB solution, on the other hand, provided conservative buckling moment estimates along the entire range of elastic buckling.

Seismic performance of R/C structures under vertical ground motion

Selcuk Bas,이종한,Mukadder Sevinc,Ilker Kalkan 사단법인 한국계산역학회 2017 Computers and Concrete, An International Journal Vol.20 No.4

The effects of the vertical component of a ground motion on the earthquake performances of semi-ductile high-rise R/C structures were investigated in the present study. Linear and non-linear time-history analyses were conducted on an existing in-service R/C building for the loading scenarios including and excluding the vertical component of the ground motion. The ratio of the vertical peak acceleration to the horizontal peak acceleration (V/H) of the ground motion was adopted as the main parameter of the study. Three different near-source earthquake records with varying V/H ratio were used in the analyses. The linear time-history analyses indicated that the incorporation of the vertical component of a ground motion into analyses greatly influences the vertical deflections of a structure and the overturning moments at its base. The lateral deflections, the angles of rotation and the base shear forces were influenced to a lesser extent. Considering the key indicators of vertical deflection and overturning moments determined from the linear time-history analysis, the non-linear analyses revealed that the changes in the forces and deformations of the structure with the inclusion of the vertical ground motion are resisted by the shear-walls. The performances and damage states of the beams were not affected by the vertical ground motion. The vertical ground motion component of earthquakes is markedly concluded to be considered for design and damage estimation of the vertical load-bearing elements of the shear-walls and columns.