Tests and finite element analysis on the local buckling of 420 MPa steel equal angle columns under axial compression

G. Shi,Z. Liu,H.Y. Ban,Y. Zhang,Y.J. Shi,Y.Q. Wang 국제구조공학회 2012 Steel and Composite Structures, An International J Vol.12 No.1

Local buckling can be ignored for hot-rolled ordinary strength steel equal angle compression members, because the width-to-thickness ratios of the leg don’t exceed the limit value. With the development of steel structures, Q420 high strength steel angles with the nominal yield strength of 420 MPa have begun to be widely used in China. Because of the high strength, the limit value of the width-to-thickness ratio becomes smaller than that of ordinary steel strength, which causes that the width-to-thickness ratios of some hot-rolled steel angle sections exceed the limit value. Consequently, local buckling must be considered for 420 MPa steel equal angles under axial compression. The existing research on the local buckling of high strength steel members under axial compression is briefly summarized, and it shows that there is lack of study on the local buckling of high strength steel equal angles under axial compression. Aiming at the local buckling of high strength steel angles, this paper conducts an axial compression experiment of 420MPa high strength steel equal angles, including 15 stub columns. The test results are compared with the corresponding design methods in ANSI/AISC 360-05 and Eurocode 3. Then a finite element model is developed to analyze the local buckling behavior of high strength steel equal angles under axial compression, and validated by the test results. Followingthe validation, a finite element parametric study is conducted to study the influences of a range of parameters, and the analysis results are compared with the design strengths by ANSI/AISC 360-05 and Eurocode 3.

Synthesis and Electrochemical Properties of LiNi_0.4Mn_1.5Cr_0.1O_4 and Li_4Ti_5O_12

G. Q. Liu,L.Wen,G. Y. Liu,H. Z. Luo,B. Y. Ma,Q. Y. Wu,Y. W. Tian 대한금속·재료학회 2011 METALS AND MATERIALS International Vol.17 No.4

Spinel compound LiNi_0.4Mn_1.5Cr_0.1O_4 (LNMCO) and Li_4Ti_5O_12 (LTO) were synthesized by the sol-gel method and the solid-state method, respectively. The particle sizes of the products LiNi_0.4Mn_1.5Cr_0.1O_4 and Li_4Ti_5O_12 were 0.5 to 2 um and 0.5 to 0.8 um, respectively. All samples exhibited excellent electrochemical properties. A LiNi_0.4Mn_1.5Cr_0.1O_4/Li_4Ti_5O_12 (LNMCO/LTO) cell was fabricated and was demonstrated to exhibit good electrochemical properties at the high current rate of 1 C. When the specific capacity was determined based on the mass of the LNMCO cathode, the LNMCO/LTO cell delivered 125 mAh g^(−1) at 1 C and 77 mAh g^(−1) at 5 C. The capacity retentions after 30 cycles were 94.4 % and 83.1 %, respectively.

The Metabolizable Energy Value, Standardized Ileal Digestibility of Amino Acids in Soybean Meal, Soy Protein Concentrate and Fermented Soybean Meal, and the Application of These Products in Early-weaned Piglets

Zhang, H.Y.,Yi, J.Q.,Piao, X.S.,Li, P.F.,Zeng, Z.K.,Wang, D.,Liu, L.,Wang, G.Q.,Han, X. Asian Australasian Association of Animal Productio 2013 Animal Bioscience Vol.26 No.5

Three experiments were conducted to evaluate the metabolizable energy (ME) value, standardized ileal digestibility (SID) of amino acids (AA) of soybean meal (SBM), soy protein concentrate (SPC) and fermented soybean meal (FSBM), and the application of these products in early-weaned piglets. In Exp. 1, four barrows with initial body weight (BW) of $14.2{\pm}1.4$ kg were used in a $4{\times}4$ Latin square design. The diet 1 contained corn as the only energy source. The other three diets replaced 25% of corn in diet 1 with one of the three soybean products, and the digestable energy (DE) and ME contents were determined by difference. In Exp. 2, four barrows (initial BW of $18.2{\pm}1.5$ kg) were fitted with ileal T-cannulas and allotted to a $4{\times}4$ Latin square design. Three cornstarch-based diets were formulated using each of the soybean products as the sole source of AA. A nitrogen-free diet was also formulated to measure endogenous losses of AA. In Exp. 3, ninety six piglets (initial BW of $5.6{\pm}0.9$ kg) weaned at $21{\pm}2$ d were blocked by weight and assigned to one of three treatments for a 21-d growth performance study. The control diet was based on corn and SBM, the two treatments' diets contained either 10% SPC or FSBM and were formulated to same SID lysine to ME ratio of 3.6 g/Mcal. The results showed that the ME content of SPC was greater than SBM (p<0.05). The SID of most AA in SPC was greater than the SID of AA in SBM (p<0.05). For the essential AA, the SID of histidine, isoleucine, leucine, lysine and threonine in FSBM were greater than in SBM (p<0.05). Even though they were fed same SID lysine to ME ratio of 3.6 g/Mcal diets, pigs fed SPC and FSBM diets had greater weight gain, G:F (p<0.05) and better fecal score (p<0.05) than pigs fed SBM diet. In conclusion, SPC showed a higher ME content and SID of AA than the SBM. SID of some essential AA in FSBM was higher than SBM and was similar with SPC. But the lower antigenic proteins and anti-nutritional factors content in SPC and FSBM may be the main factors affecting the performance of early-weaned piglets rather than the increased ME content and SID of AA.

Metabolisable Energy, In situ Rumen Degradation and In vitro Fermentation Characteristics of Linted Cottonseed Hulls, Delinted Cottonseed Hulls and Cottonseed Linter Residue

Bo, Y.K.,Yang, H.J.,Wang, W.X.,Liu, H.,Wang, G.Q.,Yu, X. Asian Australasian Association of Animal Productio 2012 Animal Bioscience Vol.25 No.2

Dietary supplementation with conventional linted cottonseed hulls (LCSH) is a common practice in livestock production all over the world. However, supplementation with mechanically delinted cottonseed hulls (DCSH) and cottonseed linter residue (CLR) is uncommon. Cottonseed by-products, including LCSH, DCSH and CLR, were assessed by chemical analysis, an in situ nylon bag technique, an in vitro cumulative gas production technique and in vitro enzyme procedure. The crude protein (CP) content of CLR (302 g/kg dry matter (DM)) was approximately 3 times that of LCSH and 5 times that of DCSH. The crude fat content was approximately 3 times higher in CLR (269 g/kg DM) than in LCSH and 4 times higher than in DCSH. Neutral detergent fibre (311 g/kg DM) and acid detergent fibre (243 g/kg DM) contents of CLR were less than half those of DCSH or LCSH. Metabolisable energy, estimated by in vitro gas production and chemical analyses, ranked as follows: CLR (12.69 kJ/kg DM)>LCSH (7.32 kJ/kg DM)>DCSH (5.82 kJ/kg DM). The in situ degradation trial showed that the highest values of effective degradability of DM and CP were obtained for CLR (p<0.05). The in vitro disappearance of ruminal DM ranked as follows: CLR>LCSH>DCSH (p<0.05). The lowest digestibility was observed for DCSH with a two-step in vitro digestion procedure (p<0.05). The potential gas production in the batch cultures did not differ for any of the three cottonseed by-product feeds. The highest concentration of total volatile fatty acids was observed in CLR after a 72 h incubation (p<0.05). The molar portions of methane were similar between all three treatments, with an average gas production of 22% (molar). The CLR contained a higher level of CP than did LCSH and DCSH, and CLR fermentation produced more propionate. The DCSH and LCSH had more NDF and ADF, which fermented into greater amounts of acetate.

Correlations between Heterozygosity at Microsatellite Loci, Mean d² and Body Weight in a Chinese Native Chicken

Liu, G.Q.,Jiang, X.P.,Wang, J.Y.,Wang, Z.Y. Asian Australasian Association of Animal Productio 2006 Animal Bioscience Vol.19 No.12

A total of two hundred twenty eight half-sib chickens were scored for allele size at 20 microsatellite loci to estimate individual heterozygosity and mean $d^2$. The averages of microsatellite heterozygosity, allele per locus and mean $d^2$ were 0.39, 3.6 and 49, respectively. The body weight was measured biweekly from birth to twelve weeks of age. Gompertz function was assumed to simulate body weight and to estimate the growth model parameters. Due to sex effect on body weight, the regression of body weight on heterozygosity as well as on mean $d^2$ in males and females was analyzed separately in the present study. Positive correlations were found between microsatellite heterozygosity and body weight in males and females (p<0.05). Positive correlation also observed between individual heterozygosity and simulated maximum daily gain estimated from Gompertz function in female chickens (p<0.05). There were no significant correlations between mean $d^2$ and body weight. The results suggest that local effect hypothesis could explain the correlations between heterozygosity and fitness-related traits in the domesticated chicken population, rather than the general effect hypothesis does.

PARAMETER MATCHIN AND OPTIMIZATION FOR A HYDRAULIC POWER-ASSISTANT SYSTEM

G.-Q. LIU,Y.-C. YAN,J. CHEN,F.-F. XU 한국자동차공학회 2010 International journal of automotive technology Vol.11 No.4

A hydraulic power-assist system is a hydraulic regeneration system that can significantly improve fuel economy when installed on a conventional bus operating in urban traffic. This paper presents a methodology for matching a new hydraulic power-assist system (HPA) to a conventional bus. The HPA and the conventional bus were modeled using the AMESim environment. The HPA was optimized using a simulation-based orthogonal design method with two indexes, the fuel economy and the acceleration performance. According to the simulation results, the volume of the accumulator was the primary factor affecting fuel economy, and the gear ratio of the transfer case was the primary factor influencing the acceleration performance. As a result, tradeoffs between the two indexes are required for a practical operational scenario. Experimental results demonstrated that the optimal HPA installed on a conventional bus was able to satisfy the acceleration performance requirement of the vehicle and also reduced fuel consumption by 25 percent.

Photocatalytic and Hydrophilic Properties of TiO₂/ Fe₂O₃ Composite Films

Q. J. Liu,Q. L,X. H. Wu,G. Q. Zhang,Z. Q. Gao,G. X. Chen 한국진공학회(ASCT) 2002 Journal of Korean Vacuum Science & Technology Vol.6 No.1

TiO₂/Fe₂O₃ composite thin films were prepared on common glass substrates by sol-gel processing and dip-drawing method. The effect of Fe₂O₃ content on the photocatalytic and hydrophilic properties of composite films was studied. The results indicate that the photocatalytic activities of composite TiO₂ films are superior to that of pure TiO₂ film, and the film containing 0.5% Fe₂O₃ has the best photocatalytic activity. The hydrophilicity is difference with variant Fe₂O₃ content, the films containing 0.05%~0.1% Fe₂O₃ have the best hydrophilicity and their contact angles are 0°.

Cluster Analysis of 12 Chinese Native Chicken Populations Using Microsatellite Markers

Chen, G.H.,Wu, X.S.,Wang, D.Q.,Qin, J.,Wu, S.L.,Zhou, Q.L.,Xie, F.,Cheng, R.,Xu, Q.,Liu, B.,Zhang, X.Y.,Olowofeso, O. Asian Australasian Association of Animal Productio 2004 Animal Bioscience Vol.17 No.8

The genomes of Chinese native chicken populations were screened using microsatellites as molecular markers. A total of, 528 individuals comprisede12 Chinese native chicken populations were typed for 7 microsatellite markers covering 5 linkage groups and genetic variations and genetic distances were also determined. In the 7 microsatellite loci, the number of alleles ranged from 2 to 7 per locus and the mean number of alleles was 4.6 per locus. By using fuzzy cluster, 12 Chinese native chicken populations were divided into three clusters. The first cluster comprised Taihe Silkies, Henan Game Chicken, Langshan Chicken, Dagu Chicken, Xiaoshan Chicken, Beijing Fatty Chicken and Luyuan Chicken. The second cluster included Chahua Chicken, Tibetan Chicken, Xianju Chicken and Baier Chicken. Gushi Chicken formed a separate cluster and demonstrated a long distance when comparing with other chicken populations.

Study on Phylogenetic Relationship Between Wild Japanese Quails in the Weishan Lake Area and Domestic Quails

Chang, G.B.,Chang, H.,Zhen, H.L.,Liu, X.P.,Sun, W.,Geng, R.Q.,Yu, Y.M.,Wang, S.C.,Geng, S.M.,Liu, X.L.,Qin, G.Q.,Shen, W. Asian Australasian Association of Animal Productio 2001 Animal Bioscience Vol.14 No.5

This paper is based on the 36 wild Japanese quails which migrated to and settled in the Weishan Lake area. The gene frequency of 10 loci encoding the enzymes in viscera and muscle was detected. After collecting the same data about 20 quail colonies in China and other countries, it clusters the 21 quail populations by fuzzy cluster analysis. The study indicates that the wild Japanese quail in the Weishan Lake area is closer to domestic quail for phylogenetic system than wild Japanese quails in Japanese Islands. The paper supports the thesis that the quail domestication area should be further studied.

Phenotypic and Genetic Parameters for Inosine Acid in Relation to Carcass and Meat Quality Traits in Pigs

Jiang, X.P.,Liu, G.Q.,Xiong, Y.Z.,Ding, J.T.,Xie, K.Z.,Zhang, J.Q.,Zuo, B. Asian Australasian Association of Animal Productio 2003 Animal Bioscience Vol.16 No.2

A total of 135 F2 finishing pigs (65 barrows and 69 gilts) from resource population (Large White${\times}$Meishan) were slaughtered at about 87.8 kg BW. Contents of inosine acid (IMP) and carnine (HR) in muscle were assayed by HLPC and genetic parameters for IMP content and HR content were estimated using full sibs model. There was significant sex effect on IMP content(p<0.05), $3.561{\pm}0.077mg/g$ for gilt and $3.287{\pm}0.085mg/g$ for barrow. Heritability estimates for IMP and HR content were 0.127 and 0.357, respectively. The phenotypic correlation between IMP content and HR was 0.335, pH (A) 0.024, water lose rate (WLR) -0.069, intramuscular fat (IMF) -0.214, average marbling score (MARB) -0.143, average backfat measurements (AVBF) -0.084 and average color value (CV) -0.156, respectively. The result indicated that inosine acid content in meat might be retained or slightly improved by reducing backfat depth in pig breeding.