http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
음의 각을 가지는 허니컴 스포크를 사용한 비 공압타이어의 접지압 분포
김광원,김두만,Kim, Kwangwon,Kim, Dooman 항공우주시스템공학회 2010 항공우주시스템공학회지 Vol.4 No.2
An airless tire has advantages over the conventional pneumatic tire in terms of flat proof and maintenance free. According to the recently disclosed inventions on the airless tire, non-pneumatic tire (NPT) consists of the flexible polygon spokes. Considering the NPT structure, the spokes undergo the tension-compression cyclic loading while the tire rolls. Therefore the spokes of NPT are required to have both stiffness and resilience under the cyclic tensile-compressible loading. In general, if a material has a high stiffness, it shows a low elastic strain limit. In this paper, using the auxetic honeycomb structure with negative poissons's ratio, the spokes of NPT tire are designed to have both stiffness and resilience. Finite element based numerical simulation of the contact pressure of a NPT is carried out with ABAQUS.
Non-linear Analysis of Radial Tire Using ABAQUS
Kyoungjin Seong,Dooman Kim,Hyunseung Yoo,Injieong Park,Sungchan Kim 한국자동차공학회 2004 한국자동차공학회 지부 학술대회 논문집 Vol.- No.-
Tire carcass is a basic structural part for maintaining stiffness of tire. As deformation property confirmation of tire carcass in transmitting or driving is essential subject with respect to tire design. Tires have geometrical shape of doughnut and consist of steel cord-rubber, which have much difference in properties, so these structures are difficult to analyze mechanically. For that reason, ABAQUS program for analyzing structural characteristics of automobile tire widely used in the fields of mechanical and automobile industries. In this study, the non-linear analysis method and numerical results of method radial tire are briefly introduced. And carcass deformation behavior of radial tire is conducted by using the ABAQUS. A calculated numerical result is compared result of experimental.
유한요소 해석을 이용한 파괴 하중에서 추간판의 응력상태 해석
유새롬(SaiRom Yoo),김두만(DooMan Kim),김진규(JinKyu kim) 대한기계학회 2011 대한기계학회 춘추학술대회 Vol.2011 No.10
Failure in a state of the intervertebral disk did not measure the stress state, because stress of intervertebral disk under failure load is difficult to study experimentally. In this paper, finite element analysis with ABAQUS is used for failure stress of intervertebral disk evaluation. According to the results of FEM analysis about human intervertebral disk under the failure load conditions, maximum stress(93 MPa) is occurred at intervertebral disk edge.
[타이어운동특성부문] X-ray영상을 이용한 PCR Tire Belt 시편의 층간전단변형율에 관한 실험적 연구
유현승(Hyungseung Yoo),박인정(Injeong Park),김두만(Dooman Kim) 한국자동차공학회 2001 한국자동차공학회 춘 추계 학술대회 논문집 Vol.2001 No.11_2
In this paper, interlaminar (interply) shear strains on the inner area of tire belt specimens were measured from images, which were taken by X-ray with experimental setup under the uniaxial extension loading. The effects of cord angle and specimens width were studied. Also, the measured results were compared with theoretical analysis. In view of qualitative analysis, good agreements were shown between experiment and theory, but some differences were shown in the quantitative analysis.
나노 입자 적층 시스템(NPDS)을 이용한 염료 감응 태양전지 - 전기 변색 통합 소자 및 에너지 하베스팅 시스템에 대한 연구
김광민,김형섭,최다현,이민지,박윤찬,추원식,천두만,이선영,Kim, Kwangmin,Kim, Hyungsub,Choi, Dahyun,Lee, Minji,Park, Yunchan,Chu, Wonshik,Chun, Dooman,Lee, Caroline Sunyong 한국마이크로전자및패키징학회 2016 마이크로전자 및 패키징학회지 Vol.23 No.2
본 연구에서는 나노 입자 적층 시스템(Nano Particle Deposition System, NPDS)을 이용하여 전기변색소자의 작동 전극을 적층하고 또한 염료 감응 태양전지의 반도체 층으로 사용되는 $TiO_2$층 및 전기변색소자의 이온 저장 층으로 사용되는 Antimony Tin Oxide(ATO) 층을 제작하였다. NPDS는 상온 건식 분말 적층법으로 노즐을 통하여 초음속으로 가속된 분말의 높은 에너지를 이용하여 기판에 적층하는 새로운 개념의 건식 적층 방법이다. 본 연구에서 코팅된 물질의 두께는 전기변색소자의 투과율에 영향을 끼치는데, 이는 표면 프로파일 측정법(surface profiling method)으로 측정하였으며, 적층된 $TiO_2$와 ATO 및 복합 층의 미세 구조를 확인하기 위해 SEM을 이용한 분석을 진행하였다. 한편 염료 감응 태양전지의 광 변환 효율은 솔라 시뮬레이터로 분석하였다. 또한 UV-visible spectrometer와 power source를 이용하여 630 nm 대역에서 전기 변색 소자가 갖는 투과도 변화와 낮은 전압에서의 작동 및 변색 횟수를 측정하였으며, 결과적으로 상기 과정을 거쳐 제작되고, 측정된 염료 감응 태양전지 - 전기 변색 통합 구조 소자를 자체 제작한 에너지 하베스팅 시스템과 연결하여 통합 구조 소자 내 태양전지의 전압 발생을 통해 자체 구동이 가능한 전기 변색 소자 시스템 제작에 성공하였다. NPDS를 통해 제작된 변색 소자의 경우, 최대 49%의 투과도 변화와 500회 작동에서 C-V curve를 유지함을 측정하여 성능과 내구성을 입증하였고, 통합 소자 내 태양 전지의 광 변환 효율은 최대 2.55%로 측정되었으며, 통합 소자 내 변색 소자의 경우 최대 26%의 투과도 변화를 보였다. In this study, Antimony Tin Oxide (ATO) ion storage layer and $TiO_2$ working electrode were fabricated using Nano Particle Deposition System. NPDS is the cutting-edge technology among the dry deposition methods. Accelerated particles are deposited on the substrate through the nozzle using NPDS. The thicknesses for coated layers were measured and layer's morphology was acquired using SEM. The fabricated electrochromic cell's transmittance was measured using UV-Visible spectrometer and power source at 630 nm. As a result, the integrated electrochromic/DSSC hybrid system was successfully fabricated as an energy harvesting system. The fabricated electrochromic cell was self-operated using DSSC as a power source. In conclusion, the electrochromic cell was operated for 500 cycles, with 49% of maximum transmittance change. Also the photovoltaic efficiency for DSSC was measured to be 2.55% while the electrochromic cell on the integrated system had resulted in 26% of maximum transmittance change.