http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
LRFD 설계법에 의한 강재보강 탄성받침의 Proto-Design
조창빈(Joh Changbin),윤혜진(Yoon Hye Jin) 한국구조물진단유지관리학회 2005 한국구조물진단학회 학술발표회논문집 Vol.9 No.2
합리적인 교량받침의 설계법의 정립은 “교량받침의 성능 및 신뢰성 향상 기술 개발” 과제의 연구 목표 중의 하나이다. 이를 위한 연구의 일환으로, 제2진도대교의 강재보강 탄성받침(Steel-Reinforced Elastomeric Bearing)을 대상으로 KS F 4420(한국산업표준협회, 1998)을 따른 설계와 AASHTO LRFD(2004) 설계법을 따른 설계로 나누어 비교분석하였다. AASHTO LRFD로 설계하는 경우, 최대허용압축응력과 최대허용전단변형비의 영향으로 Eurocode(CEN, 2000)의 영향을 받은 KS규정을 따른 경우 보다 단면적과 높이가 커지는 것으로 나타났다. 향후 국내에 LRFD 설계법을 도입할 경우, 최대허용압축응력과 최대허용전단변형비에 대한 합리적인 결정이 필요하다고 판단된다.
Structural Behavior of 3D Printed Concrete Specimens with Reinforcement
Changbin Joh(조창빈),Jungwoo Lee(이장우),In-Hwan Yang(양인환) 한국건설순환자원학회 2018 한국건설순환자원학회 논문집 Vol.6 No.3
본 연구에서는 프린트 층 사이에 부착에 초점을 두고 3D 프린팅 콘크리트의 구조거동 연구를 수행하였다. 3D 프린팅 콘크리트의 부착 및 인장강도 실험을 수행하고 일괄 타설 콘크리트 실험결과와 비교하였다. 실험변수는 콘크리트 층 사이의 프린트시간차와 철근 보강 여부이다. 콘크리트 층 사이에는 공극이 존재하고 이에 따라, 강도 감소가 발생한다. 층 사이 대부분의 인장부착 강도 감소는 응력 집중과 프린트 시간차에 기인한다. 프린트 시간차가 24시간을 초과할 때 인장부착 강도의 감소는 구조거동에 영향을 미친다. 층 사이 철근 보강은 연성거동 증진에 유용하고 구조물의 갑작스런 파괴를 예방한다. 또한, 공극이 유발한 응력 집중에 기인한 휨 강도 감소는 횡방향 하중을 받는 3D 프린트 벽체 구조물 설계시에 고려되어야 한다. This paper examines the structural behavior of 3D printed concrete specimens with focus on the bond between the layers. The tensile bond and flexural strengths were investigated experimentally and compared with those of specimens made by conventional mold casting. The test parameters were the time gap between printing layers and the reinforcement between vertical layers. The results showed the 3D printed specimens had voids between layers and confirmed the strength reduction due to printing time gap and the stress concentration caused by the voids. Most of the reduction in tensile bond strength between layers was due to the stress concentration at least up to certain printing time gap. Moreover, beyond a certain printing time gap (24hours), the additional reduction in tensile bond strength reached a level that could affect the structural behavior. The reinforcement between layers was helpful to increase the ductile behavior which is essential to prevent the sudden collapse of the structure. In addition, the reduction in flexural strength due to the stress concentration by the voids was observed and should be considered in the design of 3D printed wall structures against the lateral load.