http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
5 GHz 무선랜 응용을 위한 소형 광대역 MEMS 안테나
김지혁,김현철,전국진,Kim Ji-Hyuk,Kim Hyeon Cheol,Chun Kukjin 대한전자공학회 2006 電子工學會論文誌-TC (Telecommunications) Vol.43 No.2
MEMS 공정을 이용하여 작은 접지면과 광대역 특성을 가지는 소형 안테나를 제작하였다. 광대역 특성을 얻기 위해서 다층기판을 사용하였으며, 패치 안테나는 네개의 패치로 나누어져 있고 각각의 패치는 금속선으로 연결되어 있다. 한 개의 마스크 공정으로 간단한 제작이 가능하다. 두개의 마이크로스트립 안테나를 만들었다 A 타입 안테나는 패치들이 금속선으로 연결된 안테나이고 B 타입 안테나는 금속선으로 연결이 안된 안테나이다. 제안된 안테나의 크기는 $8{\times}12{\times}2mm^3$ 이었으며 측정결과 A 타입은 5.3GHz 중심주파수에 420MHz 대역폭, B 타입은 5.66 GHB중심주파수에 480MHz 대역폭을 가지는 것으로 나타났다. A small size broadband microstrip patch antenna with small ground plane has been fabricated using MEMS. Multiple layer substrates we used to realize small size and broadband characteristics. The microstrip patch is divided into 4 pieces and each patch is connected to each other using a metal microstrip line. The fabrication please process is simple and only one mask is needed. Two types of microtrip antennas are fabrication Type A is the microstrip antenna with metal lines and type B is the microstrip antenna without metal lines. The size of proposed microstip antenna is $8{\times}12{\times}2mm^3$ and the experimental results show that the antenna type A and type B have the bandwidth of 420MHz at 5.3 GHz and 480MHz at 5.66 GHz, respectively
WiBro 망을 이용한 2.5/3.5/5.5 ㎓ m-WiMAX 시스템 무선 측정용 주파수 변환기 개발
김세환(Sehwan Kim),전국진(Kukjin Chun) 大韓電子工學會 2011 電子工學會論文誌-TC (Telecommunications) Vol.48 No.2
WiBro 망을 이용한 쿼드 밴드 모듈 시스템을 측정하기 위해서 주파수 변환기를 개발했다. 제작된 주파수 변환기의 크기는 3.1 ㎝ × 3.1 ㎝ × 0.4 ㎝이다. 주파수 변환기 수신부의 잡음 지수는 2.62∼3.45 ㏈였으며, EVM은 -37.5∼-34.5 ㏈로 측정되었다. 그리고 송신부의 EVM은 -42.5∼-35.5 ㏈로 측정되었다. 개발된 주파수 변환기와 함께 쿼드 밴드 모듈을 제작하였고, 2.3 ㎓ 와이브로 망에서 쿼드 밴드 모듈을 테스트한 결과, 2.5 ㎓, 3.5 ㎓, 5.5 ㎓ 대역에서 원활한 인터넷 연결이 가능했다. For measuring quad-band module system using WiBro network, frequency converter was developed. The size of the fabricated frequency converter is 3.1 ㎝ × 3.1 ㎝ × 0.4 ㎝. Noise figure of the receiver part of the frequency converter was 2.62 ∼ 3.45 ㏈, EVM of that is -37.5 ㏈ ∼ -34.5 ㏈. And EVM of the transmission part was -42.5 ∼ -35.5 ㏈. Quad-band module was fabricated with the developed frequency converter. Testing the quad-band module in 2.3 ㎓ WiBro network results the excellent internet connection for 2.5 ㎓, 3.5 ㎓ and 5.5 ㎓ band.
Comb drive를 이용한 RF MEMS 스위치에 관한 연구
강성찬(Sungchan Kang),김현철(Hyeon Cheol Kim),전국진(Kukjin Chun) 대한전자공학회 2008 電子工學會論文誌-SD (Semiconductor and devices) Vol.45 No.4
본 논문에서는 comb drive를 이용하여 수평 방향 저항 접촉 방식의 RF MEMS 스위치 개발을 소개한다. 무선통신 트랜시버에서 사용되는 FEM에서 사용될 수 있는 높은 안전성과 좋은 RF 특성을 가지는 스위치의 개발을 목표로 한다. 따라서 작은 삽입손실 특성을 가지기 위해 comb drive를 이용하여 큰 접촉 힘을 발생시키고, 큰 격리도 특성을 가지기 위해 스위치 off 상태에서 작은 정전용량을 갖도록 한다. 그리고 단결정 실리콘을 스위치의 구조물로 사용함으로써 기계적인 안전성을 갖도록 한다. 개발된 RF MEMS 스위치는 26 V의 동작 전압을 가지며, 2 ㎓에서 0.44 ㏈ 이하의 삽입손실과 60 ㏈ 이상의 격리도 특성을 가진다. This paper presents a lateral resistive contact RF MEMS switch using comb drive. Our goal was to fabricate the RF MEMS switch with high reliability and good RF characteristics for front end module in wireless transceiver system. Therefore, comb drive is used for large contact force in order to achieve low insertion loss and small off-state capacitance in order to achieve high isolation. The single crystalline silicon is used for mechanical reliability. As a result, the developed switch showed insertion loss less than 0.44 ㏈ at 2 ㎓, isolation greater than 60 ㏈, and low actuation voltage at 26 V.