http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
마그네시아의 치밀화 및 입자성장에 미치는 첨가물의 영향
이해원,김환,Lee, Hae-Weon,Kim, Whan 한국세라믹학회 1982 한국세라믹학회지 Vol.19 No.2
This experiment has been carried out for the purpose of investigating the effect of additives on densification and grain growth in magnesium oxide by a two-step process; hot pressing and heat treating. MgO powder has been obtained by calcining extra reagent grade MgCO3 at 90$0^{\circ}C$ for 30 minutes, and additives have been added to $MgCO_3$ in the form of soluble salts-Al$(NO_3)_3$$. $9H_2O$ and $Cr(NO_3)_3$.9H_2O$. The hot pressing has been carried out with changes of soaking time at 125$0^{\circ}C$ under the pressure of 250kg/$\textrm{cm}^2$, and the heat treating also at same temperature. The initial particle size of MgO measured by particle size analyzer was 0.86 microns. Densification rate obeyed the equation D=K lnt + C, and grain growth rate obeyed the equation G-G0=kt1/2. It was vaporization of some $Cr_2O_3$ and formation of solid solution that had an influence on desification of MgO containing $Cr_2O_3$. Activation energy for grain growth of pure MgO was 62.4 kcal/mole, therefore grain growth was supposed to be diffusioncontrolled process. But after heat treatmeat, excess additives were expected to slow down the grain growth by the formation of second phase or the solute atoms at grainboundary.
이해원,이종호,전형우,안재평,박종구,문환,Lee, Hae-Weon,Lee, Jong-Ho,Jun, Hyung-Woo,Ahn, Jae-Pyoung,Park, Jong-Ku,Moon, Hwan 한국세라믹학회 2000 한국세라믹학회지 Vol.37 No.11
표면 윤활층을 가진 나노 알루미나를 진공중에서 가압성형함으로써 결함발생없이 높은 충전압력을 가할 수 있었으며, 높은 밀도, 미세기공, 좁은 기공경 분포를 가지는 성형체를 제조할 수 있었다. 윤활제의 화학 및 기계적 특성에 의하여 변하는 모세관 현상을 조정함으로써 충전효율을 증대하고 결함발생을 억제할 수 있다. 나노분말의 소결에서도 성형 미세구조의 균일도가 치밀화 거동에 여전히 지배적인 역할을 하였다.
탄소단섬유강화에 의한 폴리카보네이트 고분자 탄소복합재 전기적 특성 연구
이해원(Hae Weon Lee) 산업기술교육훈련학회 2017 산업기술연구논문지 (JITR) Vol.22 No.4
Carbon fiber has many properties including a large surface-to-volume ratio, chemical and thermal stability, and electrical conductivity, and high mechanical strengths. In this study, short carbon fiber reinforced thermoplastic polycarbonate polymer composite are made according to weight percent by 10wt%, 15wt.%, 20wt.%. The samples were then made by injection molding method. The conductivity properties was analyzed using a electric conductivity tester, Keithley 6220 Current Source and 4 point probe. The orientation of specimens were analysed using SEM. In addition, the electrical properties of the carbon fiber composite improved through wight percent quantity. This is because the fiber connected structure model and orientation of carbon fiber in polymer.
이해원(Hae-Won Lee),이인희(In-Hee Lee),박종원(Jong-Weon Park),최장영(Jang-Yong Choi) 한국철도학회 2019 한국철도학회 학술발표대회논문집 Vol.2019 No.5
전기철도 전력공급방식은 직류식과 교류식이 있다. 직류방식은 통신 유도장해가 없으며, 지하구간 터널 공사비가 절감된다. 교류방식은 간선철도구간에서 대용량, 고속화에 유리하다. 지하철에만 직류방식을 적용한 우리나라와 달리 유럽등 많은 국가에서는 간선철도에도 직류방식을 많이 채택하고 있다. 최근 일부 국가에서는 철도 속도향상 및 대용량 수송을 위해 직류방식을 교류방식으로 변경하고 있다. 우리나라에서는 서울지하철 1호선과 4호선의 교류-직류 연계구간 직통운전의 효율성 향상을 위해 직류구간을 교류방식으로 변경을 검토한 사례도 있었다. 본 논문에서는 국내외의 전기방식변경 및 검토 사례를 알아보고 향후 남북철도 직결운행을 위한 북한철도 현대화에 참고 할 수 있는 전력공급방식 변경 기본 절차를 정립해 보는데 의의가 있을 것이다. There are direct current(DC) method and alternating current(AC) method electric railway power supply system. The DC method has no communication induction disturbance, and the construction cost of the underground section tunnel is reduced, and the AC method is advantageous for the large capacity and high speed in the section of the main railway. Unlike Korea, which uses the DC method only in the subway, many countries including Europe have adopted the DC method in the main railway. Recently, some countries are changing the DC method to the AC method in order to improve railway speed and mass transport. In Korea, in order to improve the efficiency of direct operation of AC-DC connection section of Seoul Subway Line 1 and 4, there have been cases where the DC section was changed to AC type. In this paper, it will be meaningful to examine the changes and review cases of railway electric method at home and abroad, and to establish a basic procedure for changing the electric power supply system that can be referred to in the future for the modernization of North Korean railway.
탄소단섬유강화 PC복합소재의 노치부 유무에 따른 기계적 특성에 관한 연구
이해원(Hae-Weon Lee) 산업기술교육훈련학회 2014 산업기술연구논문지 (JITR) Vol.19 No.1
This paper discusses the notch related fracture behavior of shot-fiber reinforced thermoplastics. the stress concentration factor of the matrix the specimen with notch hole seems that the carbon content of 0%, 10% were seen with 3.29, 3.67, gradually increased. the weld specimen of carbon content of 0%, 10% were seen with 4.92, 5.91. The results of comparing the strength of the specimen in accordance with the notch of the substrate carbon fiber carbon content of 0%. 10% is seen the strength of 42.1MPa, 59.3MPa, respectively. Welding material of carbon fiber carbon content of 0%, 10% were seen with 42MPa, 44.1MPa respectively.
열경화몰딩과 반응소결을 이용한 세라믹스 실형상 제조기술 개발
이해원 ( Hae Weon Lee ),신현익 ( Hyun Ick Shin ),전형우 ( Hyung Woo Jun ),김주선 ( Joo Sun Kim ),이종호 ( Jong Ho Lee ),송휴섭 ( Hue Sup Song ) 대한금속재료학회 ( 구 대한금속학회 ) 2004 재료마당 Vol.17 No.5
본 연구는 세라믹 분말 성형 공정에서 금기시 해 오던 열경화성 수지를 결합제로 사용하여 복잡한 형상을 가지는 대형 세라믹 부품의 제조에 활용될 수 있도록 고분자 기술인 열경화몰딩기술을 세라믹 분말 성형에 성공적으로 접목하였다. 특히, 액상응결 공정에 의하여 다양한 형상과 크기 분포를 가지는 구성분말에 대해서도 균일한 과립을 제조할 수 있을 뿐만 아니라 과립의 분말 충전밀도를 조정할 수 있게 됨으로 인하여 GCM 성형공정에 의해서도 상당히 복잡한 형상의 성형체를 제조할 수 있게 되었다. 열경화성 결합제의 제한된 유동성과 변형능을 활용하여 다공성 세라믹스의 기공구조를 제어할 수 있는 가능성이 매우 크다는 사실을 고체전해질 연료전지 음극 연구를 통하여 확인한 것도 큰 의의가 있다고 하겠다. 이외에도 분말 입자간의 마찰력이 매우 크기 때문에 공학적인 의미를 부여할 수 있는 대형 부품을 성형하기 매우 어려운 나노분말의 성형에도 GM 공정이 상당히 효과적인 것을 확인하였다. 본 연구실에서는 열경화성 결합제를 사용하여 다공 성 기판에서도 결함없는 후막을 형성하는 공정과 다기능성 다공성 세라믹스 부품의 실형상 제조 공정 등에도 열경화 몰딩기술의 원리를 적용하고 응용 범위를 확 대하는 연구개발 노력을 계속하고 있다.
탄소단섬유강화 재활용 고분자복합재의 중량비에 따른 파괴거동에 관한 연구
이해원(Hae Weon Lee) 산업기술교육훈련학회 2016 산업기술연구논문지 (JITR) Vol.21 No.3
High-functional engineering plastic such as polycarbonate finally in the petrochemical process has a superior mechanical physical properties. Therefore, engineering plastics have become widely used in all industrial fields. The amount of the engineering plastics are constantly increasing. Moreover, the carbon fiber reinforced composite material utilizing carbon fibers are also being expanded application. Recently the application of the composite material reinforced by carbon fibers or glass fibers in a thermoplastic polymer resin base is increasing in many industries. There are many waste and environment problem according to abolition of use or depleted durability. Therefore, we need waste processing method of the wasted short carbon fiber reinforced composite material because it is cause the enviromnental problem.
SOFC 음극용 Ni-YSZ 복합체의 미세구조와 전기적 물성간의 상관관계: II. 경시변화
문환,이해원,이종호,윤기현,Moon, Hwan,Lee, Hae-Weon,Lee, Jong-Ho,Yoon, Ki-Hyun 한국세라믹학회 2000 한국세라믹학회지 Vol.37 No.12
Ni의 함량이 서로 다른 Ni-YSZ 복합체를 100$0^{\circ}C$ 환원 분위기 하에서 열처리하며 시간에 따른 미세구조의 변화를 관찰하였다. Quantitative microscopy 이론을 응용한 화상분석 결과 Ni-YSZ 복합체의 미세구조는 열처리시 나타나는 Ni상의 미세구조 변화에 가장 큰 영향을 받고 있었다. 특히 Ni의 양이 많은 조성에서는 Ni 상간의 접촉이 많아 고상반응에 의한 미세구조의 변화가 심하였는데 이로 인해 복합체 미세구조의 안정화가 느리게 진행되었다. Ni-YSZ 복합체의 전기 전도도 역시 Ni상의 미세구조 변화에 큰 영향을 받았는데 복합체 전체 미세구조의 경시변화와는 달리 Ni상의 많은 조성보다는 Ni상의 percolation이 일어나는 조성 부근에서 더 큰 영향을 받았다. 이로 인해 Ni-YSZ의 전기 전도도는 Ni의 percolation threshold 부근 조성에서 안정화되는데 더 많은 시간을 요하였다.