http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
Zhou Longyun,Li Xiaohu,Li Xiaojun 한국원자력학회 2024 Nuclear Engineering and Technology Vol.56 No.1
Double steel plate concrete composite shear wall (SCSW) has been widely utilized in nuclear power plants and high-rise structures, and its shear connectors have a substantial impact on the seismic performance of SCSW. Therefore, in this study, the mechanical properties of SCSW with angle stiffening ribs as shear connections were parametrically examined for the reactor containment structure of nuclear power plants. The axial compression ratio of the SCSW, the spacing of the angle stiffening rib arrangement and the thickness of the angle stiffening rib steel plate were selected as the study parameters. Four finite element models were constructed by using the finite element program named ABAQUS to verify the experimental results of our team, and 13 finite element models were established to investigate the selected three parameters. Thus, the shear capacity, deformation capacity, ductility and energy dissipation capacity of SCSW were determined. The research results show that: compared with studs, using stiffened ribs as shear connectors can significantly enhance the mechanical properties of SCSW; When the axial compression ratio is 0.3–0.4, the seismic performance of SCSW can be maximized; with the lowering of stiffener gap, the shear bearing capacity is greatly enhanced, and when the gap is lowered to a specific distance, the shear bearing capacity has no major affect; in addition, increasing the thickness of stiffeners can significantly increase the shear capacity, ductility and energy dissipation capacity of SCSW. With the rise in the thickness of angle stiffening ribs, the improvement rate of each mechanical property index slows down. Finally, the shear bearing capacity calculation formula of SCSW with angle stiffening ribs as shear connectors is derived. The average error between the theoretical calculation formula and the finite element calculation results is 8% demonstrating that the theoretical formula is reliable. This study can provide reference for the design of SCSW.
A meta-analysis on advantages of peripheral nerve block post-total knee arthroplasty
( Di You ),( Lu Qin ),( Kai Li ),( Di Li ),( Guoqing Zhao ),( Longyun Li ) 대한통증학회 2021 The Korean Journal of Pain Vol.34 No.3
Background: Postoperative pain management is crucial for patients undergoing total knee arthroplasty (TKA). There have been many recent clinical trials on post-TKA peripheral nerve block; however, they have reported inconsistent findings. In this meta-analysis, we aimed to comprehensively analyze studies on post-TKA analgesia to provide evidence-based clinical suggestions. Methods: We performed a computer-based query of PubMed, Embase, the Cochrane Library, and the Web of Science to retrieve related articles using neurothe following search terms: nerve block, nerve blockade, chemodenervation, chemical neurolysis, peridural block, epidural anesthesia, extradural anesthesia, total knee arthroplasty, total knee replacement, partial knee replacement, and others. After quality evaluation and data extraction, we analyzed the complications, visual analogue scale (VAS) score, patient satisfaction, perioperative opioid dosage, and rehabilitation indices. Evidence was rated using the Grading of Recommendations Assessment, Development, and Evaluation approach. Results: We included 16 randomized controlled trials involving 981 patients (511 receiving peripheral nerve block and 470 receiving epidural block) in the final analysis. Compared with an epidural block, a peripheral nerve block significantly reduced complications. There were no significant between-group differences in the postoperative VAS score, patient satisfaction, perioperative opioid dosage, and rehabilitation indices. Conclusions: Our findings demonstrate that the peripheral nerve block is superior to the epidural block in reducing complications without compromising the analgesic effect and patient satisfaction. Therefore, a peripheral nerve block is a safe and effective postoperative analgesic method with encouraging clinical prospects.
Yewen Wei,Longyun Kang,Zhizhen Huang,Zhen Li,Miao miao Cheng 전력전자학회 2015 JOURNAL OF POWER ELECTRONICS Vol.15 No.5
Distributed generation systems (DGSs) have been getting more and more attention in terms of renewable energy use and new generation technologies in the past decades. The self-excited induction generator (SEIG) occupies an important role in the area of energy conversion due to its low cost, robustness and simple control. Unlike synchronous generators, the SEIG has to absorb capacitive reactive power from the outer device aiming to stabilize the terminal voltage at load changes. This paper presents a novel static VAR compensator (SVC) called a magnetic energy recovery switch (MERS) to serve as a voltage controller in SEIG powered DGSs. In addition, many small scale SEIGs, instead of a single large one, are applied and devoted to promote the generation efficiency. To begin with, an expandable mathematic model based on a d-q equivalent circuit is created for parallel SEIGs. The control method of the MERS is further improved with the objective of broadening its operating range and restraining current harmonics by parameter optimization. A hybrid control strategy is developed by taking both of the stand-alone and grid-connected modes into consideration. Then simulation and experiments are carried out in the case of single and double SEIG(s) generation. Finally, the measurement results verify that the proposed DGS with SVC-MERS achieves a better stability and higher feasibility. The major advantages of the mentioned variable reactive power supplier, when compared to the STATCOM, include the adoption of a small DC capacitor, line frequency switching, simple control and less loss.
Wei, Yewen,Kang, Longyun,Huang, Zhizhen,Li, Zhen,Cheng, Miao miao The Korean Institute of Power Electronics 2015 JOURNAL OF POWER ELECTRONICS Vol.15 No.5
Distributed generation systems (DGSs) have been getting more and more attention in terms of renewable energy use and new generation technologies in the past decades. The self-excited induction generator (SEIG) occupies an important role in the area of energy conversion due to its low cost, robustness and simple control. Unlike synchronous generators, the SEIG has to absorb capacitive reactive power from the outer device aiming to stabilize the terminal voltage at load changes. This paper presents a novel static VAR compensator (SVC) called a magnetic energy recovery switch (MERS) to serve as a voltage controller in SEIG powered DGSs. In addition, many small scale SEIGs, instead of a single large one, are applied and devoted to promote the generation efficiency. To begin with, an expandable mathematic model based on a d-q equivalent circuit is created for parallel SEIGs. The control method of the MERS is further improved with the objective of broadening its operating range and restraining current harmonics by parameter optimization. A hybrid control strategy is developed by taking both of the stand-alone and grid-connected modes into consideration. Then simulation and experiments are carried out in the case of single and double SEIG(s) generation. Finally, the measurement results verify that the proposed DGS with SVC-MERS achieves a better stability and higher feasibility. The major advantages of the mentioned variable reactive power supplier, when compared to the STATCOM, include the adoption of a small DC capacitor, line frequency switching, simple control and less loss.
Long Yun,Zhu Rongsheng,Wang Dezhong,Yin Junlian,Li Tianbin 대한기계학회 2016 JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY Vol.30 No.11
The diffuser of a reactor coolant pump was optimized using an orthogonal approach with numerical simulation to improve the pump hydraulic performance. Steady simulation was conducted by solving Reynolds-averaged Naiver-Stokes equations with the SST k-ω turbulence model using CFX code. The influence of the diffuser geometric parameters, namely, S, φ, α 4 , b 4 , δ 2 , R t and R 4 , on the pump performance were determined. L 18 (3 7 ) orthogonal table was chosen for the optimization process. Best indicators were determined, and range analysis of energy losses, head, and efficiency at the rated condition was performed. Optimal parameters of the diffuser were S = 490 mm, φ = 36°, α 4 = 30°, b 4 = 200 mm, δ 2 = 20 mm, R t = 5 mm and R 4 = 565 mm. The final design was experimentally tested. Simulation results showed more remarkable performance than the experimental result. However, the numerical predictions and experimental results were consistent, validating the design procedure. Loading of the impeller and diffuser blades was analyzed to investigate the direct impact on the hydrodynamic flow field. The head was 14.74 m, efficiency was 79.6 %, and efficiency of the prototype pump was 83.3 % when the model pump functioned at the rated conditions. Optimization results showed that efficiency and head were improved at the design condition.