http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
- 中文 을 입력하시려면 zhongwen을 입력하시고 space를누르시면됩니다.
- 北京 을 입력하시려면 beijing을 입력하시고 space를 누르시면 됩니다.
RISS 인기검색어
- 검색키워드
- 저자 : Chenglong Zhu (검색결과 5 건)
- 무료
- 기관 내 무료
- 유료
-
Chenglong Zhu,Baomin Li,Jianwei Xia,Na Zhang,Rui Liu 제어·로봇·시스템학회 2022 International Journal of Control, Automation, and Vol.20 No.6
In this paper, an adaptive event-triggered asymptotic tracking control problem is addressed for switched nonlinear systems with unknown control directions. In existing control schemes, the proposed controller is not directly aimed at the original system, which affects the control performance. Different from the existing control schemes, based on the original system, an event-triggered control law is constructed in this paper. The proposed event-triggered controller guarantees that the tracking error ς1 asymptotically converges to the origin. Finally, the effectiveness of the proposed controller design scheme is proved by simulation examples.
-
Flow blockage analysis for fuel assembly in a lead-based fast reactor
Wang, Chenglong,Wu, Di,Gui, Minyang,Cai, Rong,Zhu, Dahuan,Zhang, Dalin,Tian, Wenxi,Qiu, Suizheng,Su, G.H. Korean Nuclear Society 2021 Nuclear Engineering and Technology Vol.53 No.10
Flow blockage of the fuel assembly in the lead-based fast reactor (LFR) may produce critical local spots, which will result in cladding failure and threaten reactor safety. In this study, the flow blockage characteristics were analyzed with the sub-channel analysis method, and the circumferentially-varied method was employed for considering the non-uniform distribution of circumferential temperature. The developed sub-channel analysis code SACOS-PB was validated by a heat transfer experiment in a blocked 19-rod bundle cooled by lead-bismuth eutectic. The deviations between the predicted coolant temperature and experimental values are within ±5%, including small and large flow blockage scenarios. And the temperature distributions of the fuel rod could be better simulated by the circumferentially-varied method for the small blockage scenario. Based on the validated code, the analysis of blockage characteristics was conducted. It could be seen from the temperature and flow distributions that a large blockage accident is more destructive compared with a small one. The sensitivity analysis shows that the closer the blockage location is to the exit, the more dangerous the accident is. Similarly, a larger blockage length will lead to a more serious case. And a higher exit temperature will be generated resulting from a higher peak coolant temperature of the blocked region. This work could provide a reference for the future design and development of the LFR.
-
Synthesis of aminated calcium lignosulfonate and its adsorption properties for azo dyes
Yingying Wang,Linli Zhu,Xiaohong Wang,Wanru Zheng,Chen Hao,Chenglong Jiang,Jingbo Wu 한국공업화학회 2018 Journal of Industrial and Engineering Chemistry Vol.61 No.-
A low-cost adsorbent, aminated calcium lignosulfonate (ACLS) was prepared and successfully applied to the adsorption of Congo red and the Titan yellow dyes. The adsorbent was characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FT-IR), elemental mapping images (EMIs) and Brunauer–Emmett–Teller (BET) analysis. And the efficiency of ACLS for the removal of Congo red and the Titan yellow dyes was evaluated by several factors, such as temperature, pH, adsorbent dose, contact time and initial concentration of dyes solution. And the test ranges of temperature, pH, adsorbent dose, contact time and initial concentration of dye solution were 25–45 °C, 2–12, 0.005–0.05 g, 1–48 h, 10–200 mg L−1, respectively. The adsorption results demonstrated a good ability to remove dye with the removal rates of 97% and 91% for 30 mg L−1 Congo red and 40 mg L−1 Titan yellow, respectively. The adsorption kinetic and adsorption isotherms can be well described by the pseudo second order kinetic and the Langmuir isotherm model for the both dyes, respectively. Moreover, the maximum adsorption capacity of Congo red and Titan yellow reached 258.4 mg g−1 and 190.1 mg g−1 in the study of the Langmuir adsorption isotherm, respectively. Thermodynamic studies show that the adsorption of the two dyes is a spontaneous endothermic process. The results indicate that the ACLS has the potential to be used in the treatment of dye wastewater.
-
Jian Chen,Wangyang Zhang,Chenglong Wang,Di Liu,Linbo Zhu 대한기계학회 2022 JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY Vol.36 No.9
The contact behavior of hemisphere pressed by a rigid flat is analyzed based on the finite element method under the condition of independent varying elastic moduli (E) and yield strengths (Y). The contact behavior is related to the ratio of E/Y. The mean contact pressure (p*) first increases and then decreases with the increasing interference, and this trend is more obvious for the contact of materials with the comparatively small ratio of E/Y. The end of the elastoplastic range or the inception of the fully plastic range is determined according to the interference corresponding to the peak value of the p*. The contact load and area in elastoplastic and fully plastic ranges are determined by the interference and the ratio of E/Y. Then, a new contact model to accurately predict the contact load and area for a wide range of E and Y is proposed, and compared with the previous models. The correctness of the current model is verified by the experimental measurement results recorded in previous literature.
-
Loading-unloading model of contact between elastic-plastic ellipsoid and rigid plane
Jian Chen,Wangyang Zhang,Di Liu,Chenglong Wang,Linbo Zhu 대한기계학회 2023 JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY Vol.37 No.8
The mechanical behaviour of the ellipsoidal asperity and rigid planes during loading and unloading are fundamental problems in contact mechanics. This study investigates the contact between elastic-perfectly plastic ellipsoidal asperity for different ellipticities and rigid planes under normal conditions during the loading and unloading process using the finite element method. The results show that the changing trend of the contact load, residual displacement, contact area, and plastic work with displacement under different ellipticities is similar, but the magnitude is different. The contact area during unloading is not always smaller than that during loading with the same displacement. Moreover, the initial unloading stage contact area is larger than that of the loading stage. Based on the numerical model calculation results, analytical dimensionless expressions are proposed for the residual displacement, plastic work, contact area, and contact load after fully unloading the ellipsoids with different ellipticities for a wide range of displacements. The prediction results from previous models are used to verify the effectiveness and correctness of the proposed equations. These empirical relations can be combined with statistical or fractal methods to study the contact behaviour of macroscopic rough surfaces.
ScienceON연관 검색어 추천
이 검색어로 많이 본 자료
활용도 높은 자료
