http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
김주형(Juhyong Kim),조삼덕(Sam-Deak Cho),이광우(Kwang-Wu Lee),장갑식(Gap-Shik Chang) 한국토목섬유학회 2010 한국토목섬유학회 학술발표회 Vol.2010 No.11
연직배수재 내부의 유로 내의 흐름 상태를 평가하기 위해 연직배수재의 단면을 이상화 한 표준 금속판을 이용하여 통수능 시험 을 수행한 결과/ 동수경사가 증가함에 따라 통수능은 감소하는 양상을 나타 내었다. 또한/ 충류상태로 판정된 영역 내에서도 동수경사가 작을수록 통수능이 증가하는 양상을 나타내 었으며/ 약 32 - 45 % 정도의 상대적인 차이를 나타내고 있음을 확인하였다 This paper studies on hydraulic gradient effect for discharge capacity of vertical drain boards. It is found that hydraulic gradient (i) 0.5, specified in KS K 0940, remains in the condition of laminar flow. However, discharge capacity of drain still varies about 32~45% although flow state is under laminar flow.
수중 가압식 매립방법을 이용한 석탄회 저강도고유동화재의 고밀도화 특성
김주형(Juhyong Kim),조삼덕(Samdeok Cho),김욱기(Ukgie Kim),공진영(Jinyoung Kong),정혁상(Hyuksang Jung),천병식(Byungsik Chun) 한국지반환경공학회 2013 한국지반환경공학회논문집 Vol.14 No.2
본 연구에서는 수중 가압식 매립방법을 이용하여 석탄회를 주재료로 하는 저강도 고유동화재(CLSM)를 대상으로 매립재 고밀도화 가능성에 대한 모형시험을 수행하고 그 결과를 분석하였다. 배출압에 의한 밀도 변화는 저강도 고유동화재를 구성하는 매립회와 비회의 배합비에 큰 영향을 받고 배출관의 위치에 따라서도 큰 영향을 받는 것으로 나타났다. 수중에서 가압 배출하는 경우, 배출관 주변을 중심으로 단위중량이 상대적으로 큰 것으로 나타나 배출압으로 인한 주변지반 밀도 증가효과가 발생하는 것으로 나타났으며, 실제 매립현장에서도 배출압의 효과를 이용할 수 있을 것으로 판단된다. This study introduces a densification technique of controlled low strength materials (CLSM) made with coal ashes by pump discharge pressure. Based on a small-scale laboratory test results, unit weight of CLSM around discharge pipe is greater than that of relatively some distant area from discharge pipe. It is also found that densification of CLSM depends on not only mixture rate of pond ash but also fly ash and location of discharge pipe.
김주형(Kim Juhyong),조삼덕(Cho Samdeok),공진영(Kong Jinyoung),정혁상(Jung Hyuksang),천병식(Chun Byungsik) 한국지반환경공학회 2010 한국지반환경공학회논문집 Vol.11 No.11
석탄회를 주재료로 하는 저강도 고유동화재의 특성을 분석하기 위해 일축압축강도시험을 수행하였으며, 경화 시간을 분석 하였다. 동일한 배합비 상태에서 함수비가 낮을수록 일축압축강도 증가율이 큰 것으로 나타났으며, 초기 3일 동안에는 이와 같은 현상이 뚜렷하게 나타나고 있음을 확인하였다. 또한, 가장 경제적인 시멘트 첨가비로 소형 모형지반을 조성하여 동적콘관입시험을 통해 배합비에 따른 저강도 고유동화재의 특성을 분석한 결과, 목표 일축압축강도인 500㎪(콘관입률 20㎜/blow) 도달시간은 약 10일 정도 소요되는 것으로 나타났으며, 10일이 경과한 후에는 배합비와 상관없이 경화속도가 급격하게 감소하는 것으로 나타났다. Unconfined compressive strength tests were performed to evaluate curing characteristics of controlled low strength material(CLSM) made with coal ashes. It is found that unconfined compressive strength normalized by curing times, increases as decreasing the water contents of CLSM particularly during first three days. Dynamic cone penetrometer tests were also carried out to evaluate cost-effective CLSM lump strength characteristics with time. It takes around 10 days to reach target strength, 500㎪ (penetration rate, 20㎜/blow). Curing rate significantly decreases after 10 days elapsed regardless of CLSM formulation.
해수와 담수에서 점탄성을 갖는 그라우트재의 공학적 특성 평가
김욱기(Kim, Ukgie),조삼덕(Cho, Samdeok),박봉근(Park, Bonggeun),송병덕(Song, Byeongdeok),김주형(Kim, Juhyong) 한국지반환경공학회 2012 한국지반환경공학회논문집 Vol.13 No.6
일반적인 그라우팅 재료는 물속에서 재료 분리가 발생하여 수중 그라우팅 작업시 시공 품질 확보가 매우 어렵다. 최근에는 다양한 혼화제를 첨가하여 수중에서 재료분리가 발생하지 않는 수중 불분리성의 그라우팅 재료들이 개발되고 있다. 본 연구에서는 계면활성제계 개질제를 이용하여 수중에서 재료분리가 발생하지 않으면서도 유동성을 충분히 갖는 점탄성 그라우트재를 개발하고 실내시험을 통해 해수 및 담수에 수중 불분리성 그라우팅 재료와 일반 그라우팅 재료를 시공하였을 때의 공학적 특성을 분석하였다. 본 연구에서 개발한 수중 불분리성 그라우팅 재료는 일반 그라우트재와 비교하여 해수와 담수 상태에서 충분한 강도가 발휘되었으며 수중에서 재료 분리가 발생하지 않아 수중에서도 좋은 시공 품질을 확보할 수 있을 것으로 평가되었다. In general, it is critical that grout consistency permit the complete filling of void space without segregation of ingredients. Recently, the antiwashout agent is used on underwater grout materials for preventing the grout from the segregation in water. This study introduces a new type of antiwashout underwater and flowable grout material using viscous modifiers and its characteristics comparing with conventional grout materials in fresh and sea water. It is found that the antiwashout underwater grout both in fresh and sea water has enough strength and good resistance to segregation.
지지부재로 이형철근을 설치하는 띠형 강보강재의 인발성능 평가
정성규(Sung-gyu Jung),김주형(Juhyong Kim),조삼덕(Samdeok Cho),이광우(Kwangwu Lee) 한국지반신소재학회 2013 한국지반신소재학회 논문집 Vol.12 No.4
본 연구에서는 지지부재가 설치된 띠형 강보강재에 대한 실내인발시험을 수행하였다. 주문진 표준사를 사용하여 상대밀도 80%인 모형지반을 조성하였고, 지지부재의 개수를 0∼2개로 구분하여 실내인발시험을 수행하였다. 상재압은 50kN/m²∼200kN/m²까지 4단계로 구분하여 적용하였고, 1mm/min 속도로 강보강재를 인발하였다. 표면이 매끄러운 띠형 강보강재의 인발저항력은 보강재 표면과 지반 사이에서 마찰저항만 발현되기 때문에 인발 초기에 급격히 증가하다가 지속적으로 감소하는 경향을 나타낸다. 반면, 지지부재를 설치한 강보강재의 인발저항력은 마찰저항뿐만 아니라 수동저항도 함께 발현되므로 계속적으로 증가하는 것으로 나타났다. 보강재의 형태에 관계없이 최대인발저항은 상재압이 증가함에 따라 선형적으로 증가하는 것으로 나타났다. 지지부재를 1개 설치한 경우에 비해 지지부재를 2개 설치했을 때의 최대수동저항은 작게 나타났다. 이는 지지부재의 설치 간격 및 위치에 따라 지지부재에서 발현되는 수동저항의 크기가 다르기 때문에 나타나는 현상으로 판단되며, 지지부재 설치 위치 및 간격에 따른 추가 인발시험을 통해 확인할 필요가 있다. Laboratory pullout tests were conducted to evaluate pullout performance of steel strip reinforcements with deformed steel bars as transverse members. The steel strip reinforcement has an installation hole to assemble a deformed steel bar. Jumunjin standard sand is used to form a relative density of ground model to 80%. Frictional resistance of steel strip reinforcement without transverse member increases sharply at the initial displacement and quickly decreases with displacement. Maximum frictional resistance increases linearly as normal pressure increasing, and soil-reinforcement interaction friction angle(P<sub>peak</sub>) of a steel strip reinforcement is estimated to 14.64°. Passive resistance increases with displacement and converge into maximum passive resistance in most cases. Maximum passive resistance increases linearly as normal pressure increasing irrespective of shape of the steel reinforcement. Pullout force of steel strip reinforcements with installation holes or transverse members largely increases about 4 to 7 times compared to frictional resistance force of steel strip reinforcements when embedment length(L<sub>e</sub>) of steel strip reinforcements is 500 mm. In the case of using 2 transverse members, interference effect is observed due to the spacing of 2 transverse members and location of assembly holes and transverse members.