열원에서의 증기응축을 위한 냉각장치의 랜킨사이클에 대한 고찰

安樂善 忠州大學校 1988 한국교통대학교 논문집 Vol.22 No.-

Heat engine that changes heat energy into mechanical work does heat exchange between high heat source and low while working fluid undergoes cycle process. When you design and operate a heat engine you should consider not only the cycle itself but the heat exchange process and should calculate the optimum condition. In high heat source there is a heat loss of itself owing to different temperature with surroundings and part of heat transmitted to working fluid in cycle also discharges directly into the air because of heat loss at pipe arrangement and the turbine. In this paper I examined on the output change and the maximum output condition in accordance with the operation condition of reversible cycle and on the operation condition of the cycle to calculate the maximum output by Rankin cycle. I studied on the typical Rankin Cycle by calculationg outputs with various operation condition and examined the results.

응축수 탱크내에서의 수격현상과 냉각장치의 랜킨 사이클에 대한 고찰

安樂善 충주대학교 산업대학원 1999 大學院論文輯 Vol.1 No.-

A delivery valve has installed to a way out pump in order to control keeping off counter flow and delivery volume in case of an accident of out of order pump. Condensing water has been supplied to a boiler by circulation pump through a condensing tank contained condenser cooling system or boiler condensing water. A shutting down of a pump operation by sudden interception a circulation pump decreased cooling water or delivery volume of supplying water. By this a sudden water hammer is causes in the system,ocording to pump characteristic,driving condition of delivery valve the feature of geometry in system and condensing water condition water hammer was changed and the destruction in system can be happened in violence. In this paper. I have made a numerical value analysis on the water hammer affected by the change of a section for materials in system applicating to driving condition of delivery value. In this paper I examined on the output change and the maximum output condition in accordance with the operation condition of reversible cycle and on the operation condition of the cycle to calculate the maximum output by Rankin Cycle. I studied on the typical Rankin Cycle by calculating outputs with various operation condition and examined the results.

SM 20C 강에 있어서 高溫表面 疲勞균열 성장과정에 관한 고찰

安樂善 忠州大學校 1986 한국교통대학교 논문집 Vol.19 No.2

The mechanical materials which they has used in an fluid and gas atmosphere of high temperature should be good state of persevering-oxidation and corrosion. They should sufficiently be in possession strength at high temperature. The design of structure materials and estimation of satisfaction has satisfactorily been difficult as a design mothod by allowance stress giving suitable satistaction at tensile stress of materials and yilding point. It is necessary specific character that be introduced the conception by technologically using breaking mechanics to sufficiently analysis and interpretation. In general, adding to pre-stress as tensile stress and compression to materials at the normal temperature should be changed fatigue limit with work hardening. In this paper, I have experimentally received change to fatigue limit as elevated temperature that I have applied heat to 400℃ temperature from normal temperature SM 20C steel. I have experimentally studied about to the birth of a small surface crack and the specific glowing. I have theoretically writed about applying to breaking mechanics and limit point.

周速式 減速機의 齒形과 一般齒車와의 比較 연구

安樂善 충주대학교 1990 한국교통대학교 논문집 Vol.24 No.-

In this paper, I have studied on the harmonic drive compared with actual profile. I have obtained the result as followe: 1. harmonic drive could obtained high speed ratio, high torque capacity and high reduction ratio. 2. Harmonic drive has largely used as a good many gearing tooth form. 3. Harmonic drive has a good many changed tooth form gearing charateristic according to eccentricity shift coefficient and eccentric facfor. 4. We can obtaine a good proper shift coefficient by strength analysis.

一般齒車와 周速式 減速機에 대한 考찰

李鍾赫,安樂善 忠州大學校 1996 한국교통대학교 논문집 Vol.31 No.1

In this paper, I have studied on the harmonic drive compared with actual profile. I have obtained the result as follows:The analysis carried out in a plane mechanism. From the analysis of the motion of the rigid gear and the flexible gear, the shapes of the rolling contact plates which move together with each tooth are derived, assuming that the toohh of the flexible gear is rigid although the tooth groove is flexible and that the pitch if the tiith on the unstrechable neutral line of the flexible gear is contact. 1. Harmonic drive could obtain high speed ratio, high torque capacity and high reduction ratio. 2. Harmonic drive has largely used as a gool gearingtooth form. 3. We can obtain a good proper shift coefficiented by strength analysis.

SM20C강의 열피로 특성에 관한 연구 : 열피로균열 성장과정을 중심으로 Centering around to propagation behavior of heat fatigue crack

安樂善,李鍾赫 충주대 산업과학기술연구소 1998 産業科學論文集 Vol.6 No.-

The mechanical materials which they has used in an fluid and gas atmosphere of high temperature should be good state of persevering-oxidation and corrosion. They should sufficiently be in possession strength at high temperature. The design of structure materials and estimation of satisfaction has satisfactorily been difficult as a design method allowance stress giving suitable satisfaction at tensile stress of materials and yilding point. It is necessary specific character that be introduced the conception by technologically using breaking mechanics to sufficiently analysis and interpretation. In general, adding to pre-stress as tensile stress and compression to materials at the normal temperature should be changed fatigue limit with work hardening. In this paper, I have experimentally received change to fatigue limit as elevated temperature that I have applied heat to 400℃ temperature from normal temperature SM 20C steel. I have experimentally studied about to the birth of a small surface crack and the specific glowing. I have theoretically writed about applying to breaking mechanics and limit point.

보일러 포화증기 회수중의 응축수 탱크내에서의 수격 현상에 관한 고찰

安樂善 忠州大學校 1987 한국교통대학교 논문집 Vol.21 No.-

A delivery valve has installed to a was out pump in order to control keeping off counter flow and delivery volume in case of an accident of out of order pump. Condensing water has been supplied to a boiler by circulation pump through a condensing tank Condensing tank contained condenser cooling system or boiler condensing water. A shutting down of a pump operation by sudden interception a circulation pump decreased cooling water or delivery volume of supplying water. By this a sudden water hammer is caused in the system. According to pump characteristic, driving condition of delivery valve the feature of geometry in system and condensing water condition, water hammer was changed and the destruction in system can be happened in violence. In this paper, I have made a numerical value analysis on the water hammer affected by the change of a section for materials in system applycating to driving condition of delivery value. Pump characteristic and a water hammer equation when the pump stopped suddenly.

평벨트에 작용하는 장력과 미끄럼속도 및 마찰특성에 관한 고찰

安樂善 忠州大學校 1989 한국교통대학교 논문집 Vol.23 No.-

The belts has been used for power transmission between two shafs. The belts do grinding between grain size of grinding and workpiece, and the necessary power is transmitted by friction between belt friction surface and pulley. The flat belts for power transmission are composed of tensile element and friction surface. Resulting from the strength, flexibleness and durability, the cotton belts has generally been used. In this paper, I have studied on the relation of tensile forces belt and pulley for cotton flat belts and for normal and tangencial friction forces distribution. I have compared them with their friction characteristics and it was suggested theoretical formula as a surface model. I have studied on the phenomenon creeping, sliding velocity and fric-tion coefficient of friction surface.

Belt-Pulley 간의 접촉으로 인한 특성에 관한 고찰

안락선 충주대 산업과학기술연구소 1994 産業科學論文集 Vol.2 No.-

The belt has been used for power transmission between two shafts. The belts do grinding between grain size of grinding and work piece, and the neceessary power is transmitted by friction between belt friction surface and pulley. The flat belts for power transmission are composed of tansile element and friction surface. Resulting from the strength, flexibleness and durability, the cotton belts has generally been used. In this paper, I have studied on the relation of tensile forces belt and pulley cotton flat belts and for V-belts. I have compared them with their friction characteristics and it was suggested theoretical formula as a surface panel. I have studies on the phenomenon creeping. friction coefficient of friction surface and tension force.

SM 20C강의 應力 및 溫度가 미치는 열피로 Crack발생 전파거동에 대한 考察

안락선 忠州大學校 1986 한국교통대학교 논문집 Vol.20 No.1

With respect to structural carbon steel(SM 20 C), it was studied the growth ratio of fatigue crack on the surface materials at a slip band occurance and the crack propagation curve of the surface materials. Obtained results are summerized as follows. 1. It does not change the crack propagation curve adding to more stress after a slip band occurance at a base stress. Because, under the base stress, the hardness value of surface test piece has a little stage. 2. By base stress, at the crack propagation stage adding to more stress, has occurance accelerating crack propagation. 3. By high stress, there is a dislocation structure near crack of fatigue steel and the fatigue crack according to slip face. The crack make growth by the slip face.