Experimental and numerical disbond localization analyses of a notched plate repaired with a CFRP patch

Abderahmane, Sahli,Mokhtar, Bouziane M.,Smail, Benbarek,Wayne, Steven F.,Zhang, Liang,Belabbes, Bachir Bouiadjra,Boualem, Serier Techno-Press 2017 Structural Engineering and Mechanics, An Int'l Jou Vol.63 No.3

Through the use of finite element analysis and acoustic emission techniques we have evaluated the interfacial failure of a carbon fiber reinforced polymer (CFRP) repair patch on a notched aluminum substrate. The repair of cracks is a very common and widely used practice in the aeronautics field to extend the life of cracked sheet metal panels. The process consists of adhesively bonding a patch that encompasses the notched site to provide additional strength, thereby increasing life and avoiding costly replacements. The mechanical strength of the bonded joint relies mainly on the bonding of the adhesive to the plate and patch stiffness. Stress concentrations at crack tips promote disbonding of the composite patch from the substrate, consequently reducing the bonded area, which makes this a critical aspect of repair effectiveness. In this paper we examine patch disbonding by calculating the influence of notch tip stress on disbond area and verify computational results with acoustic emission (AE) measurements obtained from specimens subjected to uniaxial tension. The FE results showed that disbonding first occurs between the patch and the substrate close to free edge of the patch followed by failure around the tip of the notch, both highest stress regions. Experimental results revealed that cement adhesion at the aluminum interface was the limiting factor in patch performance. The patch did not appear to strengthen the aluminum substrate when measured by stress-strain due to early stage disbonding. Analysis of the AE signals provided insight to the disbond locations and progression at the metal-adhesive interface. Crack growth from the notch in the aluminum was not observed until the stress reached a critical level, an instant before final fracture, which was unaffected by the patch due to early stage disbonding. The FE model was further utilized to study the effects of patch fiber orientation and increased adhesive strength. The model revealed that the effectiveness of patch repairs is strongly dependent upon the combined interactions of adhesive bond strength and fiber orientation.

Experimental and numerical disbond localization analyses of a notched plate repaired with a CFRP patch

Sahli Abderahmane,Bouziane M. Mokhtar,Benbarek Smail,Steven F. Wayne,Liang Zhang,Bachir Bouiadjra Belabbes,Serier Boualem 국제구조공학회 2017 Structural Engineering and Mechanics, An Int'l Jou Vol.63 No.3

Through the use of finite element analysis and acoustic emission techniques we have evaluated the interfacial failure of a carbon fiber reinforced polymer (CFRP) repair patch on a notched aluminum substrate. The repair of cracks is a very common and widely used practice in the aeronautics field to extend the life of cracked sheet metal panels. The process consists of adhesively bonding a patch that encompasses the notched site to provide additional strength, thereby increasing life and avoiding costly replacements. The mechanical strength of the bonded joint relies mainly on the bonding of the adhesive to the plate and patch stiffness. Stress concentrations at crack tips promote disbonding of the composite patch from the substrate, consequently reducing the bonded area, which makes this a critical aspect of repair effectiveness. In this paper we examine patch disbonding by calculating the influence of notch tip stress on disbond area and verify computational results with acoustic emission (AE) measurements obtained from specimens subjected to uniaxial tension. The FE results showed that disbonding first occurs between the patch and the substrate close to free edge of the patch followed by failure around the tip of the notch, both highest stress regions. Experimental results revealed that cement adhesion at the aluminum interface was the limiting factor in patch performance. The patch did not appear to strengthen the aluminum substrate when measured by stress-strain due to early stage disbonding. Analysis of the AE signals provided insight to the disbond locations and progression at the metaladhesive interface. Crack growth from the notch in the aluminum was not observed until the stress reached a critical level, an instant before final fracture, which was unaffected by the patch due to early stage disbonding. The FE model was further utilized to study the effects of patch fiber orientation and increased adhesive strength. The model revealed that the effectiveness of patch repairs is strongly dependent upon the combined interactions of adhesive bond strength and fiber orientation.

Fracture behavior modeling of a 3D crack emanated from bony inclusion in the cement PMMA of total hip replacement

Mohamed, Cherfi,Abderahmane, Sahli,Benbarek, Smail Techno-Press 2018 Structural Engineering and Mechanics, An Int'l Jou Vol.66 No.1

In orthopedic surgery and in particular in total hip arthroplasty, the implant fixation is carried out using a surgical cement called polymethylmethacrylat (PMMA). This cement has to insure a good adhesion between implant and bone and a good load distribution to the bone. By its fragile nature, the cement can easily break when it is subjected to a high stress gradient by presenting a craze zone in the vicinity of inclusion. The focus of this study is to analyze the effect of inclusion in some zone of cement in which the loading condition can lead to the crack opening leading to their propagation and consequently the aseptic loosening of the THR. In this study, the fracture behavior of the bone cement including a strange body (bone remain) from which the onset of a crack is supposed. The effect of loading condition, the geometry, the presence of both crack and inclusion on the stress distribution and the fracture behavior of the cement. Results show that the highest stresses are located around the sharp tip of bony inclusion. Most critical cracks are located in the middle of the cement mantle when they are subjected to one leg standing state loading during walking.

Thickness stretching and nonlinear hygro-thermo-mechanical loading effects on bending behavior of FG beams

Faicel Khadraoui,Abderahmane Menasria,Belgacem Mamen,Abdelhakim Bouhadra,Fouad Bourada,Soumia Benguediab,Kouider Halim Benrahou,Mohamed Benguediab,Abdelouahed Tounsi 국제구조공학회 2022 Structural Engineering and Mechanics, An Int'l Jou Vol.84 No.6

This study attempts to investigate the impact of thickness stretching and nonlinear hygro-thermo-mechanical loading on the bending behavior of FG beams. Young’s modulus, thermal expansion, and moisture concentration coefficients vary gradually and continuously according to a power-law distribution in terms of the volume fractions of the constituent materials. In addition, the interaction between the thermal, mechanical, and moisture loads is involved in the governing equilibrium equations. Using the present developed analytical model and Navier’s solution technique, the numerical results of non-dimensional stresses and displacements are compared with those obtained by other 3D theories. Furthermore, the present analytical model is appropriate for investigating the static bending of FG beams exposed to intense hygro-thermo-mechanical loading used for special technical applications in aerospace, automobile, and civil engineering constructions.

Study and analysis of a tapered shaft in composite materials with variable speed of rotation

Rachid Zahi,Abderahmane Sahli,Djafar Ait Kaci,Fouad Bourada,Abdelouahed Tounsi,Mofareh Hassan Ghazwani 국제구조공학회 2023 Structural Engineering and Mechanics, An Int'l Jou Vol.87 No.2

This paper presents a mechanical model of a “tapered composite shaft” rotating at a constant speed around its axis. The spatial equations of motion are solved using the Lagrange technique, and a finite element approach is employed to construct the model. Theoretical analysis is used to compute the kinetic and strain energies. A comparison is made between conventional finite element methods and hierarchical finite element methods, indicating that the former uses fewer elements and provides higher accuracy in determining natural frequencies. Numerical calculations are performed to determine the eigen frequencies and critical speeds of the rotating composite shaft. The critical speeds of composite shaft systems are compared with existing literature to validate the proposed model.

Fracture behavior modeling of a 3D crack emanated from bony inclusion in the cement PMMA of total hip replacement

Cherfi Mohamed,Sahli Abderahmane,Smail Benbarek 국제구조공학회 2018 Structural Engineering and Mechanics, An Int'l Jou Vol.66 No.1

In orthopedic surgery and in particular in total hip arthroplasty, the implant fixation is carried out using a surgical cement called polymethylmethacrylat (PMMA). This cement has to insure a good adhesion between implant and bone and a good load distribution to the bone. By its fragile nature, the cement can easily break when it is subjected to a high stress gradient by presenting a craze zone in the vicinity of inclusion. The focus of this study is to analyze the effect of inclusion in some zone of cement in which the loading condition can lead to the crack opening leading to their propagation and consequently the aseptic loosening of the THR. In this study, the fracture behavior of the bone cement including a strange body (bone remain) from which the onset of a crack is supposed. The effect of loading condition, the geometry, the presence of both crack and inclusion on the stress distribution and the fracture behavior of the cement. Results show that the highest stresses are located around the sharp tip of bony inclusion. Most critical cracks are located in the middle of the cement mantle when they are subjected to one leg standing state loading during walking.

Theoretical buckling analysis of inhomogeneous plates under various thermal gradients and boundary conditions

Laid Lekouara,Belgacem Mamen,Abdelhakim Bouhadra,Abderahmane Menasria,Kouider Halim Benrahou,Abdelouahed Tounsi,Mohammed A. Al-Osta 국제구조공학회 2023 Structural Engineering and Mechanics, An Int'l Jou Vol.86 No.4

This study investigates the theoretical thermal buckling analyses of thick porous rectangular functionally graded (FG) plates with different geometrical boundary conditions resting on a Winkler-Pasternak elastic foundation using a new higherorder shear deformation theory (HSDT). This new theory has only four unknowns and involves indeterminate integral variables in which no shear correction factor is required. The variation of material properties across the plate’s thickness is considered continuous and varied following a simple power law as a function of volume fractions of the constituents. The effect of porosity with two different types of distribution is also included. The current formulation considers the Von Karman nonlinearity, and the stability equations are developed using the virtual works principle. The thermal gradients are involved and assumed to change across the FG plate’s thickness according to nonlinear, linear, and uniform distributions. The accuracy of the newly proposed theory has been validated by comparing the present results with the results obtained from the previously published theories. The effects of porosity, boundary conditions, foundation parameters, power index, plate aspect ratio, and side-to-thickness ratio on the critical buckling temperature are studied and discussed in detail.

Combined influence of variable distribution models and boundary conditions on the thermodynamic behavior of FG sandwich plates lying on various elastic foundations

Djamel Eddine Lafi,Abdelhakim Bouhadra,Belgacem Mamen,Abderahmane Menasria,Mohamed Bourada,Abdelmoumen Anis Bousahla,Fouad Bourada,Abdelouahed Tounsi,Abdeldjebbar Tounsi,Murat Yaylacı 국제구조공학회 2024 Structural Engineering and Mechanics, An Int'l Jou Vol.89 No.2

The present research investigates the thermodynamically bending behavior of FG sandwich plates, laying on the Winkler/Pasternak/Kerr foundation with various boundary conditions, subjected to harmonic thermal load varying through thickness. The supposed FG sandwich plate has three layers with a ceramic core. The constituents’ volume fractions of the lower and upper faces vary gradually in the direction of the FG sandwich plate thickness. This variation is performed according to various models: a Power law, Trigonometric, Viola-Tornabene, and the Exponential model, while the core is constantly homogeneous. The displacement field considered in the current work contains integral terms and fewer unknowns than other theories in the literature. The corresponding equations of motion are derived based on Hamilton’s principle. The impact of the distribution model, scheme, aspect ratio, side-to-thickness ratio, boundary conditions, and elastic foundations on thermodynamic bending are examined in this study. The deflections obtained for the sandwich plate without elastic foundations have the lowest values for all boundary conditions. In addition, the minimum deflection values are obtained for the exponential volume fraction law model. The sandwich plate’s non-dimensional deflection increases as the aspect ratio increases for all distribution models.

Study of the fracture behavior of different structures by the extended finite element method (X-FEM)

Zagane Mohammed El Sallah,Moulgada Abdelmadjid,Sahli Abderahmane,Baltach Abdelghani,Benouis Ali Techno-Press 2023 Advances in materials research Vol.12 No.4

The fracture mechanics make it possible to characterize the behavior with cracking of structures using parameters quantifiable in the sense of the engineer, in particular the stress field, the size of the crack, and the resistance to cracking of the material. Any structure contains defects, whether they were introduced during the production of the part (machining or molding defects for example). The aim of this work is to determine numerically by the finite element method the stress concentration factor Kt of a plate subjected to a tensile loading containing a lateral form defect with different sizes: a semicircle of different radii, a notch with different opening angles and a crack of different lengths. The crack propagation is then determined using the extended finite element technique (X-FEM). The modeling was carried out using the ABAQUS calculation code.

Numerical simulation of the femur fracture under static loading

Zagane Mohammed El Sallah,Benbarek Smail,Sahli Abderahmane,B. Bachir Bouiadjra,Serier Boualem 국제구조공학회 2016 Structural Engineering and Mechanics, An Int'l Jou Vol.60 No.3

Bone is a living material with a complex hierarchical structure that gives it remarkable mechanical properties. Bone constantly undergoes mechanical. Its quality and resistance to fracture is constantly changing over time through the process of bone remodeling. Numerical modeling allows the study of the bone mechanical behavior and the prediction of different trauma caused by accidents without expose humans to real tests. The aim of this work is the modeling of the femur fracture under static solicitation to create a numerical model to simulate this element fracture. This modeling will contribute to improve the design of the indoor environment to be better safe for the passengers’ transportation means. Results show that vertical loading leads to the femur neck fracture and horizontal loading leads to the fracture of the femur diaphysis. The isotropic consideration of the bone leads to bone fracture by crack propagation but the orthotropic consideration leads to the fragmentation of the bone.