The Study of the Cycle Time Improvement by Work-In-Process Statistical Process Control Method for IC Foundry Manufacturing

Yu Cheng Lin,Chih Hung Tsai,Rong Kwei Li,Ching Piao Chen,Hsien Ching Chen 한국품질경영학회 2008 The Asian Journal on Quality Vol.9 No.3

The definition of cycle time is the time from the wafer start to the wafer output. It usually takes one or two months to get the product since customer decides to produce it. The cycle time is a critical factor for customer satisfaction because it represents the response time to the market. Long cycle time reflects the ineffective investment for the capital. The cycle time is very important for foundry because long cycle time will cause customer unsatisfied and the order loss. Consequently, all of the foundries put lots of human source in the cycle time improvement. Usually, we make decisions based on the experience in the cycle time management. We have no mechanism or theory for cycle time management. We do work-in-process (WIP) management based on turn rate and standard WIP (STD WIP) set by experiences. But the experience didn`t mean the optimal solution, when the situation changed, the cycle time or the standard WIP will also be changed. The experience will not always be applicable. If we only have the experience and no mechanism, management will not be work out. After interview several foundry fab managers, all of the fab can`t reflect the situation. That is, all of them will have an impact period after product mix or utilization varied. In this study, we want to develop a formula for standard WIP and use statistical process control (SPC) concept to set WIP upper/lower limit level. When WIP exceed the limit level, it will trigger action plans to compensate WIP Profile. If WIP Profile balances, we don`t need too much WIP. So WIP level could be reduced and cycle time also could be reduced.

Platelet-Derived Growth Factor Receptor-α Subunit Targeting Suppresses Metastasis in Advanced Thyroid Cancer In Vitro and In Vivo

( Ching-ling Lin ),( Ming-lin Tsai ),( Yu-hsin Chen ),( Wei-ni Liu ),( Chun-yu Lin ),( Kai-wen Hsu ),( Chien-yu Huang ),( Yu-jia Chang ),( Po-li Wei ),( Shu-huey Chen ),( Li-chi Huang ),( Chia-hwa Lee 한국응용약물학회 2021 Biomolecules & Therapeutics(구 응용약물학회지) Vol.29 No.5

Thyroid cancer is the most common endocrine malignancy. Patients with well-differentiated thyroid cancers, such as papillary and follicular cancers, have a favorable prognosis. However, poorly differentiated thyroid cancers, such as medullary, squamous and anaplastic advanced thyroid cancers, are very aggressive and insensitive to radioiodine treatment. Thus, novel therapies that attenuate metastasis are urgently needed. We found that both PDGFC and PDGFRA are predominantly expressed in thyroid cancers and that the survival rate is significantly lower in patients with high PDGFRA expression. This finding indicates the important role of PDGF/PDGFR signaling in thyroid cancer development. Next, we established a SW579 squamous thyroid cancer cell line with 95.6% PDGFRA gene insertion and deletions (indels) through CRISPR/Cas9. Protein and invasion analysis showed a dramatic loss in EMT marker expression and metastatic ability. Furthermore, xenograft tumors derived from PDGFRA geneedited SW579 cells exhibited a minor decrease in tumor growth. However, distant lung metastasis was completely abolished upon PDGFRA gene editing, implying that PDGFRA could be an effective target to inhibit distant metastasis in advanced thyroid cancers. To translate this finding to the clinic, we used the most relevant multikinase inhibitor, imatinib, to inhibit PDGFRA signaling. The results showed that imatinib significantly suppressed cell growth, induced cell cycle arrest and cell death in SW579 cells. Our developed noninvasive apoptosis detection sensor (NIADS) indicated that imatinib induced cell apoptosis through caspase-3 activation. In conclusion, we believe that developing a specific and selective targeted therapy for PDGFRA would effectively suppress PDGFRA-mediated cancer aggressiveness in advanced thyroid cancers.

The Study of the Cycle Time Improvement by Work-In-Process Statistical Process Control Method for IC Foundry Manufacturing

Lin, Yu-Cheng,Tsai, Chih-Hung,Li, Rong-Kwei,Chen, Ching-Piao,Chen, Hsien-Ching The Korean Society for Quality Management 2008 The Asian Journal on Quality Vol.9 No.3

The definition of cycle time is the time from the wafer start to the wafer output. It usually takes one or two months to get the product since customer decides to produce it. The cycle time is a critical factor for customer satisfaction because it represents the response time to the market. Long cycle time reflects the ineffective investment for the capital. The cycle time is very important for foundry because long cycle time will cause customer unsatisfied and the order loss. Consequently, all of the foundries put lots of human source in the cycle time improvement. Usually, we make decisions based on the experience in the cycle time management. We have no mechanism or theory for cycle time management. We do work-in-process (WIP) management based on turn rate and standard WIP (STD WIP) set by experiences. But the experience didn't mean the optimal solution, when the situation changed, the cycle time or the standard WIP will also be changed. The experience will not always be applicable. If we only have the experience and no mechanism, management will not be work out. After interview several foundry fab managers, all of the fab can't reflect the situation. That is, all of them will have an impact period after product mix or utilization varied. In this study, we want to develop a formula for standard WIP and use statistical process control (SPC) concept to set WIP upper/lower limit level. When WIP exceed the limit level, it will trigger action plans to compensate WIP Profile. If WIP Profile balances, we don't need too much WIP. So WIP level could be reduced and cycle time also could be reduced.

Research on the WIP-based Dispatching Rules for Photolithography Area in Wafer Fabrication Industries

Lin, Yu-Hsin,Tsai, Chih-Hung,Lee, Ching-En,Chiu, Chung-Ching The Korean Society for Quality Management 2007 The Asian Journal on Quality Vol.8 No.2

Constructing an effective production control policy is the most important issue in wafer fabrication factories. Most of researches focus on the input regulations of wafer fabrication. Although many of these policies have been proven to be effective for wafer fabrication manufacturing, in practical, there is a need to help operators decide which lots should be pulled in the right time and to develop a systematic way to alleviate the long queues at the bottleneck workstation. The purpose of this study is to construct a photolithography workstation dispatching rule (PADR). This dispatching rule considers several characteristics of wafer fabrication and influential factors. Then utilize the weights and threshold values to design a hierarchical priority rule. A simulation model is also constructed to demonstrate the effect of the PADR dispatching rule. The PADR performs better in throughput, yield rate, and mean cycle time than FIFO (First-In-First-Out) and SPT (Shortest Process Time).

Photocatalytic study of Zinc Oxide with bismuth doping prepared by spray pyrolysis

Lin, Tzu-Yang,Hsu, Yu-Ting,Lan, Wen-How,Huang, Chien-Jung,Chen, Lung-Chien,Huang, Yu-Hsuan,Lin, Jia-Ching,Chang, Kuo-Jen,Lin, Wen-Jen,Huang, Kai-Feng Techno-Press 2015 Advances in nano research Vol.3 No.3

The unintentionally doped and bismuth (Bi) doped zinc oxide (ZnO) films were prepared by spray pyrolysis at $450^{\circ}C$ with zinc acetate and bismuth nitrate precursor. The n-type conduction with concentration $6.13{\times}10^{16}cm^{-3}$ can be observed for the unintentionally doped ZnO. With the increasing of bismuth nitrate concentration in precursor, the p-type conduction can be observed. The p-type concentration $4.44{\times}10^{17}cm^{-3}$ can be achieved for the film with the Bi/Zn atomic ratio 5% in the precursor. The photoluminescence spectroscopy with HeCd laser light source was studied for films with different Bi doping. The photocatalytic activity for the unintentionally doped and Bi-doped ZnO films was studied through the photodegradation of Congo red under UV light illumination. The effects of different Bi contents on photocatalytic activity are studied and discussed. Results show that appropriate Bi doping in ZnO can increase photocatalytic activity.

Immune Reconstitution Inflammatory Syndrome-Like Reaction During the Treatment of Pneumocystis jirovecii Pneumonia in an Infant With Severe Combined Immunodeficiency

Lin Ching-Yu,Lim Sung-Min,Kim Soo-Yeon,Hahn Seung-Min,Ahn Jong Gyun,Kang Ji-Man 대한소아감염학회 2024 Pediatric Infection and Vaccine Vol.31 No.1

The effectiveness of corticosteroids in preventing immune reconstitution inflammatory syndrome in non-human immunodeficiency viruses Pneumocystis carinii pneumonia (PCP) patients, such as severe combined immunodeficiency (SCID) patients, is controversial. We experienced a paradoxical reaction during severe PCP treatment in a SCID infant, which responded well to adjuvant corticosteroids.

Research on the WIP-based Dispatching Rules for Photolithography Area in Wafer Fabrication Industries

( Yu Hsin Lin ),( Chih Hung Tsai ),( Ching En Lee ),( Chung Ching Chiu ) 한국품질경영학회 2007 The Asian Journal on Quality Vol.8 No.2

Constructing an effective production control policy is the most important issue in wafer fabrication factories. Most of researches focus on the input regulations of wafer fabrication. Although many of these policies have been proven to be effective for wafer fabrication manufacturing, in practical, there is a need to help operators decide which lots should be pulled in the right time and to develop a systematic way to alleviate the long queues at the bottleneck workstation. The purpose of this study is to construct a photolithography workstation dispatching rule (PADR). This dispatching rule considers several characteristics of wafer fabrication and influential factors. Then utilize the weights and threshold values to design a hierarchical priority rule. A simulation model is also constructed to demonstrate the effect of the PADR dispatching rule. The PADR performs better in throughput, yield rate, and mean cycle time than FIFO (First-In-First-Out) and SPT (Shortest Process Time).

CONSUMER LOCAL-GLOBAL IDENTITY, BRAND ORIGIN, AND CODE-SWITCHED AD EFFECTIVENESS AMONG MONOLINGUALS

Ying-Ching Lin,Kai-Yu Wang 글로벌지식마케팅경영학회 2016 Global Marketing Conference Vol.2016 No.7

There has been an increasing trend of using code-switching to enhance ad persuasion among local and global brands. Ads that include two or more languages are referred to as code-switched ads (Luna and Peracchio 2005a; 2005b). It is noted that previous studies investigating code-switched ad effectiveness have focused on bilinguals, not monolinguals. Due to the emerging use of code-switching in ads in monolingual markets, more research efforts are required to understand its effectiveness and boundaries among the monolinguals. The purpose of this study is to investigate the moderating role of consumer local-global identity in the effectiveness of code-switched ads among monolinguals. Two experiments were conducted and the results confirmed our hypothesis that consumer local-global identity moderates the effect of code-switched ads. The results indicated that congruence between consumer local-global identity and code-switching enhanced persuasiveness. In addition, the mediating effect of ad involvement was identified. These findings provide managerial implications for marketers.

Mitigating SYN flooding Attack and ARP Spoofing in SDN Data Plane

Ting-Yu Lin,Jhen-Ping Wu,Pei-Hsuan Hung,Ching-Hsuan Shao,Yu-Ting Wang,Yun-Zhan Cai,Meng-Hsun Tsai 한국통신학회 2020 한국통신학회 APNOMS Vol.2020 No.09

As the number of network devices increases rapidly, it becomes more and more difficult to defend network attacks. Large-scaled attacks, such as SYN flooding, may lead to heavy burden to the switches as well as the controller in a software defined network (SDN). In this paper, we investigate the SYN flooding and Address Resolution Protocol (ARP) spoofing attacks in SDN, and then propose mechanisms to address these two attacks. We also present a new scheme to detect SYN flooding by using only a few forwarding rules. Moreover, we utilize the Programming Protocol-independent Packet Processors (P4) technique to mitigate the burden of the controller.

Factors Related to Treatment Refusal in Taiwanese Cancer Patients

Chiang, Ting-Yu,Wang, Chao-Hui,Lin, Yu-Fen,Chou, Shu-Lan,Wang, Ching-Ting,Juang, Hsiao-Ting,Lin, Yung-Chang,Lin, Mei-Hsiang Asian Pacific Journal of Cancer Prevention 2015 Asian Pacific journal of cancer prevention Vol.16 No.8

Background: Incidence and mortality rates for cancer have increased dramatically in the recent 30 years in Taiwan. However, not all patients receive treatment. Treatment refusal might impair patient survival and life quality. In order to improve this situation, we proposed this study to evaluate factors that are related to refusal of treatment in cancer patients via a cancer case manager system. Materials and Methods: This study analysed data from a case management system during the period from 2010 to 2012 at a medical center in Northern Taiwan. We enrolled a total of 14,974 patients who were diagnosed with cancer. Using the PRECEDE Model as a framework, we conducted logistic regression analysis to identify independent variables that are significantly associated with refusal of therapy in cancer patients. A multivariate logistic regression model was also applied to estimate adjusted the odds ratios (ORs) with 95% confidence intervals (95%CI). Results: A total of 253 patients (1.69%) refused treatment. The multivariate logistic regression result showed that the high risk factors for refusal of treatment in cancer patient included: concerns about adverse effects (p<0.001), poor performance(p<0.001), changes in medical condition (p<0.001), timing of case manager contact (p=.026), the methods by which case manager contact patients (p<0.001) and the frequency that case managers contact patients (${\geq}10times$) (p=0.016). Conclusions: Cancer patients who refuse treatment have poor survival. The present study provides evidence of factors that are related to refusal of therapy and might be helpful for further application and improvement of cancer care.