Nanostructured Bulk Ceramics (Part I)

Han, Young-Hwan,Mukherjee, Amiya K. The Korean Ceramic Society 2009 한국세라믹학회지 Vol.46 No.3

The processing and characterization of ceramic nanocomposites, which produce bulk nanostructures with attractive mechanical properties, have been emphasized and introduced at Prof. Mukherjee's Lab at UC Davis. The following subjects will be introduced in detail in Part II, III, and IV. In Part II, the paper will describe a three-phase alumina-based nanoceramic composite demonstrating superplasticity at a surprisingly lower temperature and higher strain rate. The next part will show that an alumina-carbon nanotube-niobium nanocomposite produced fracture toughness values that are three times higher than that of pure nanocrystalline alumina. It was possible to take advantage of both fiber-toughening and ductile-metal toughening in this investigation. In the fourth section, discussed will be a silicon-nitride/silicon-carbide nanocomposite, produced by pyrolysis of liquid polymer precursors, demonstrating one of the lowest creep rates reported so far in ceramics at the comparable temperature of $1400^{\circ}C$. This was first achieved by avoiding the oxynitride glass phase at the intergrain boundaries. One important factor in the processing of these nanocomposites was the use of the electrical field assisted sintering method. This allowed the sintering to be completed at significantly lower temperatures and during much shorter times. These improvements in mechanical properties will be discussed in the context of the results from the microstructural investigations.

Nanostructured Bulk Ceramics (Part Ⅰ)

한영환,Amiya K. Mukherjee 한국세라믹학회 2009 한국세라믹학회지 Vol.46 No.3

The processing and characterization of ceramic nanocomposites, which produce bulk nanostructures with attractive mechanical properties, have been emphasized and introduced at Prof. Mukherjee’s Lab at UC Davis. The following subjects will be introduced in detail in Part ⅡI, Ⅲ, and Ⅳ. In Part Ⅱ, the paper will describe a three-phase alumina-based nanoceramic composite demonstrating superplasticity at a surprisingly lower temperature and higher strain rate. The next part will show that an alumina-carbon nanotube-niobium nanocomposite produced fracture toughness values that are three times higher than that of pure nanocrystalline alumina. It was possible to take advantage of both fiber-toughening and ductile-metal toughening in this investigation. In the fourth section, discussed will be a silicon-nitride/silicon-carbide nanocomposite, produced by pyrolysis of liquid polymer precursors, demonstrating one of the lowest creep rates reported so far in ceramics at the comparable temperature of 1400℃ This was first achieved by avoiding the oxynitride glass phase at the intergrain boundaries. One important factor in the processing of these nanocomposites was the use of the electrical field assisted sintering method. This allowed the sintering to be completed at significantly lower temperatures and during much shorter times. These improvements in mechanical properties will be discussed in the context of the results from the microstructural investigations. The processing and characterization of ceramic nanocomposites, which produce bulk nanostructures with attractive mechanical properties, have been emphasized and introduced at Prof. Mukherjee’s Lab at UC Davis. The following subjects will be introduced in detail in Part ⅡI, Ⅲ, and Ⅳ. In Part Ⅱ, the paper will describe a three-phase alumina-based nanoceramic composite demonstrating superplasticity at a surprisingly lower temperature and higher strain rate. The next part will show that an alumina-carbon nanotube-niobium nanocomposite produced fracture toughness values that are three times higher than that of pure nanocrystalline alumina. It was possible to take advantage of both fiber-toughening and ductile-metal toughening in this investigation. In the fourth section, discussed will be a silicon-nitride/silicon-carbide nanocomposite, produced by pyrolysis of liquid polymer precursors, demonstrating one of the lowest creep rates reported so far in ceramics at the comparable temperature of 1400℃ This was first achieved by avoiding the oxynitride glass phase at the intergrain boundaries. One important factor in the processing of these nanocomposites was the use of the electrical field assisted sintering method. This allowed the sintering to be completed at significantly lower temperatures and during much shorter times. These improvements in mechanical properties will be discussed in the context of the results from the microstructural investigations.

A dragonfly inspired flapping wing actuated by electro active polymers

Mukherjee, Sujoy,Ganguli, Ranjan Techno-Press 2010 Smart Structures and Systems, An International Jou Vol.6 No.7

An energy-based variational approach is used for structural dynamic modeling of the IPMC (Ionic Polymer Metal Composites) flapping wing. Dynamic characteristics of the wing are analyzed using numerical simulations. Starting with the initial design, critical parameters which have influence on the performance of the wing are identified through parametric studies. An optimization study is performed to obtain improved flapping actuation of the IPMC wing. It is shown that the optimization algorithm leads to a flapping wing with dimensions similar to the dragonfly Aeshna Multicolor wing. An unsteady aerodynamic model based on modified strip theory is used to obtain the aerodynamic forces. It is found that the IPMC wing generates sufficient lift to support its own weight and carry a small payload. It is therefore a potential candidate for flapping wing of micro air vehicles.

Morphological variables restrict flower choice of Lycaenid butterfly species: implication for pollination and conservation

Mukherjee, Subha Shankar,Hossain, Asif The Ecological Society of Korea 2021 Journal of Ecology and Environment Vol.45 No.1

Background: Butterflies make an important part for plant-pollinator guild. These are nectar feeder or occasionally pollen feeder and thus proboscis of the butterfly species are considered as one of the most important variable in relation to the collection of food from plants. In butterfly-plant association, nectar source is principally determined by quality of nectar, corolla length, and nectar quantity. For the butterfly, nectar uptake is determined by proboscis length because flowers with long corolla restrict butterfly species containing shorter proboscis. Empirical studies proved that butterfly species with high wing loading visit clustered flowers and species with low wing loading confined their visit to solitary or less nectar rich flowers. The present study tries to investigate the flower preference of butterfly species from Lycaenidae family having very short proboscis, lower body length, lower body weight and wing span than the most species belonging from Nymphalidae, Pieridae, Papilionidae, and Hesperiidae. Results: Butterflies with shorter proboscis cannot access nectar from deeper flower. Although they mainly visit on less deeper flower to sucking nectar, butterflies with high wing loading visits clustered flowers to fulfill their energy requirements. In this study, we demonstrated flower choice of seven butterfly species belonging to Lycanidiae family. The proboscis length maintains a positive relationship with body length and body weight. Body length maintains a positive relationship with body weight and wing span. Wing span indicate a strong positive relationship with body weight. This study proved that these seven butterfly species namely Castalius rosimon (CRN), Taracus nara (TNA), Zizinia otis (ZOT), Zizula hylax (ZHY), Jamides celeno (JCE), Chilades laius (CLA), and Psuedozizeeria maha (PMA) visit frequently in Tridax procumbens (TPR), Ocimum americanum (OAM) and Syndrella nodiflora (SNO). The species do not visit Lantana camara (LCA) and Catharanthus roseus (CRO) plants. Conclusion: The present study proved that butterfly species visits frequently in Tridax procumbens (TPR), Ocimum americanum (OAM) but less frequently in Syndrella nodiflora (SNO). So, that study determined the butterfly species helps in pollination of these herbs that in turn helps the conservation of these butterfly species.

Simulation of tissue differentiation around acetabular cups: the effects of implant-bone relative displacement and polar gap

Mukherjee, Kaushik,Gupta, Sanjay Techno-Press 2014 Advances in biomechanics & applications Vol.1 No.2

Peri-acetabular bone ingrowth plays a crucial role in long-term stability of press-fit acetabular cups. A poor bone ingrowth often results in increased cup migration, leading to aseptic loosening of the implant. The rate of peri-prosthetic bone formation is also affected by the polar gap that may be introduced during implantation. Applying a mechano-regulatory tissue differentiation algorithm on a two-dimensional plane strain microscale model, representing implant-bone interface, the objectives of the study are to gain an insight into the process of peri-prosthetic tissue differentiation and to investigate its relationship with implant-bone relative displacement and size of the polar gap. Implant-bone relative displacement was found to have a considerable influence on bone healing and peri-acetabular bone ingrowth. An increase in implant-bone relative displacement from $20{\mu}m$ to $100{\mu}m$ resulted in an increase in fibrous tissue formation from 22% to 60% and reduction in bone formation from 70% to 38% within the polar gap. The increase in fibrous tissue formation and subsequent decrease in bone formation leads to weakening of the implant-bone interface strength. In comparison, the effect of polar gap on bone healing and peri-acetabular bone ingrowth was less pronounced. Polar gap up to 5 mm was found to be progressively filled with bone under favourable implant-bone relative displacements of $20{\mu}m$ along tangential and $20{\mu}m$ along normal directions. However, the average Young's modulus of the newly formed tissue layer reduced from 2200 MPa to 1200 MPa with an increase in polar gap from 0.5 mm to 5 mm, suggesting the formation of a low strength tissue for increased polar gap. Based on this study, it may be concluded that a polar gap less than 0.5 mm seems favourable for an increase in strength of the implant-bone interface.

Construction of bivariate asymmetric copulas

Mukherjee, Saikat,Lee, Youngsaeng,Kim, Jong-Min,Jang, Jun,Park, Jeong-Soo The Korean Statistical Society 2018 Communications for statistical applications and me Vol.25 No.2

Copulas are a tool for constructing multivariate distributions and formalizing the dependence structure between random variables. From copula literature review, there are a few asymmetric copulas available so far while data collected from the real world often exhibit asymmetric nature. This necessitates developing asymmetric copulas. In this study, we discuss a method to construct a new class of bivariate asymmetric copulas based on products of symmetric (sometimes asymmetric) copulas with powered arguments in order to determine if the proposed construction can offer an added value for modeling asymmetric bivariate data. With these newly constructed copulas, we investigate dependence properties and measure of association between random variables. In addition, the test of symmetry of data and the estimation of hyper-parameters by the maximum likelihood method are discussed. With two real example such as car rental data and economic indicators data, we perform the goodness-of-fit test of our proposed asymmetric copulas. For these data, some of the proposed models turned out to be successful whereas the existing copulas were mostly unsuccessful. The method of presented here can be useful in fields such as finance, climate and social science.

Plant Disease Identification using Deep Neural Networks

Mukherjee, Subham,Kumar, Pradeep,Saini, Rajkumar,Roy, Partha Pratim,Dogra, Debi Prosad,Kim, Byung-Gyu Korea Multimedia Society 2017 The journal of multimedia information system Vol.4 No.4

Automatic identification of disease in plants from their leaves is one of the most challenging task to researchers. Diseases among plants degrade their performance and results into a huge reduction of agricultural products. Therefore, early and accurate diagnosis of such disease is of the utmost importance. The advancement in deep Convolutional Neural Network (CNN) has change the way of processing images as compared to traditional image processing techniques. Deep learning architectures are composed of multiple processing layers that learn the representations of data with multiple levels of abstraction. Therefore, proved highly effective in comparison to many state-of-the-art works. In this paper, we present a plant disease identification methodology from their leaves using deep CNNs. For this, we have adopted GoogLeNet that is considered a powerful architecture of deep learning to identify the disease types. Transfer learning has been used to fine tune the pre-trained model. An accuracy of 85.04% has been recorded in the identification of four disease class in Apple plant leaves. Finally, a comparison with other models has been performed to show the effectiveness of the approach.

Magnon bistability in a hybrid cavity–magnon system

Mukherjee Kousik,Jana Paresh Chandra 한국물리학회 2023 THE JOURNAL OF THE KOREAN PHYSICAL SOCIETY Vol.82 No.4

We have explored the magnon bistability in cavity–magnon system. The stationary solution of the Heisenberg–Langevin equation is obtained numerically and magnon profle is studied as function of diferent experimentally feasible system parameters. The magnon profle shows an anticlockwise hysteresis loop and the loop area increases with input power. The mean magnon number shows bistable nature. The Kittel mode can transit from one stable state to another stable state near two transition points. The threshold powers of transition and bistable region strongly depend on magnon dissipation rate, photon-magnon coupling strength, and Kerr nonlinear strength. This study confrms that bistable quantum states may supply a platform to describe bistability at macroscopic regime in nonlinear systems. This study may also be used in potential applications in magnetic spintronics.

Wind induced pressure on 'Y' plan shape tall building

Mukherjee, Sourav,Chakraborty, Souvik,Dalui, Sujit Kumar,Ahuja, Ashok Kumar Techno-Press 2014 Wind and Structures, An International Journal (WAS Vol.19 No.5

This paper presents a comprehensive study of pressure developed on different faces of a 'Y' plan shape tall building using both numerical and experimental means. The experiment has been conducted in boundary layer wind tunnel located at Indian Institute of Technology Roorkee, India for flow condition corresponding to terrain category II of IS:875 (Part 3) - 1987, at a mean wind velocity of 10 m/s. Numerical study has been carried out under similar condition using computational fluid dynamics (CFD) package of ANSYS, namely ANSYS CFX. Two turbulence models, viz., $k-{\varepsilon}$ and Shear Stress Transport (SST) have been used. Good conformity among the numerical and experimental results have been observed with SST model yielding results of higher magnitude. Peculiar pressure distribution on certain faces has been observed due to interference effect. Furthermore, flow pattern around the model has also been studied to explain the phenomenon occurring around the model.

Hypericum source of natural antimicrobials

Mukherjee, Pulok K.,Wahile, Atul,Ahamed, KFH Nazeer,Rajan, S. Kyung Hee Oriental Medicine Research Center 2003 Oriental pharmacy and experimental medicine Vol.3 No.3

Plants of the genus Hypericum (Family - Hypericaceae) are herbs, shrubs or small trees and are distributed chiefly in the temperate regions of the world. About 400 different species of Hypericum are available throughout the globe and 20 species occur in India, including a few cultivated in gardens. Almost all plants of the genus Hypericum are widely used in folk medicine. Several potent phytoconstituents from different Hypericum species have led to the isolation of antibacterial, antifungal and cytotoxic compounds. With the development of resistance and cross resistance with different microorganisms and the evolution of so many deadly diseases the screening and evaluation of the phytoconstituents so much so the development of varied phytoconstituents for the drug development for these deadly diseases is utmost essential in every aspects. The present review on the antimicrobial use of different Hypericum reports the findings from and extensive literature search on the Hypericum species around the globe that have been assessed for antimicrobial and antiviral activity. An attempt has been made through this review to summarize the information in this aspect in order to highlight the promising species of this genus which are worthy for further investigation as leads for drug development. Over 31 different Hypericum species have been reported to possess such activities with their varied number of phytoconstituents. Sixteen different constituents of six different classes of phytoconstituents have been reported to be present in different varieties of Hypericum, which may be considered responsible for this activity.