http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
Querzoli, Adrian L.,Hoadley, Andrew F.A.,Dyson, Tony E.S. 한국화학공학회 2003 Korean Journal of Chemical Engineering Vol.20 No.4
This study investigates improving the energy efficiency of two key refining processes: the Crude Distillation Unit (CDU) and the Residue Cracking Unit (RCU). The research methodology followed the ‘targeting before design’ approach. The CDU is a ‘tightly pinched’ system, with limited opportunities for further energy savings. The RCU actual △T_(min) is around 55℃ indicating a low level of current heat recovery. The Total-Site analysis shows that theoretically 18MW of heat could be transferred from the RCU to the CDU, reducing CDU requirements by 40% for a new or grass roots design. RCU retrofit designs were developed to increase steam generation by up to 35% and in line with targeting estimates would appear to have economic potential. The alternative CDU-RCU retrofit design was developed to decrease CDU hot utility use. Although the Total-Site profile demonstrated strong potential for heat integration, this retrofit design is not commercially attractive, as the decrease in CDU fuel does not offset the cost of reduced steam generation. This demonstrates the need to consider the different fuel and steam costs in the Total-Site analysis.
Phipps, Michelle A.,Hoadley, Andrew F.A. 한국화학공학회 2003 Korean Journal of Chemical Engineering Vol.20 No.4
Heat integration techniques can be used to optimize the energy requirement for both new and retrofit plant designs. Software tools for identifying retrofit options are becoming available. This paper reports our experiences from using heat exchanger network (HEN) optimization software for a retrofit case study of an oil refinery process. The HEN optimization software was used to automate the search for the most beneficial retrofit designs following the twostage process proposed by Asante and Zhu. The software provided three potential retrofit designs. Results from this analysis were used as the basis of a rigorous mass and energy balance simulation of the plant. The simulation corroborated the energy savings, but there were some important differences. The simulation required 20% more heat exchange area. Furthermore, the retrofit design involving one topology change was shown to be less economic than an alternative design. These differences are discussed and a revised methodology is proposed.
Liu, Jianfang,Lichtenberg, Tara,Hoadley, Katherine A.,Poisson, Laila M.,Lazar, Alexander J.,Cherniack, Andrew D.,Kovatich, Albert J.,Benz, Christopher C.,Levine, Douglas A.,Lee, Adrian V.,Omberg, Lars Elsevier 2018 Cell Vol.173 No.2
<P><B>Summary</B></P> <P>For a decade, The Cancer Genome Atlas (TCGA) program collected clinicopathologic annotation data along with multi-platform molecular profiles of more than 11,000 human tumors across 33 different cancer types. TCGA clinical data contain key features representing the democratized nature of the data collection process. To ensure proper use of this large clinical dataset associated with genomic features, we developed a standardized dataset named the TCGA Pan-Cancer Clinical Data Resource (TCGA-CDR), which includes four major clinical outcome endpoints. In addition to detailing major challenges and statistical limitations encountered during the effort of integrating the acquired clinical data, we present a summary that includes endpoint usage recommendations for each cancer type. These TCGA-CDR findings appear to be consistent with cancer genomics studies independent of the TCGA effort and provide opportunities for investigating cancer biology using clinical correlates at an unprecedented scale.</P> <P><B>Highlights</B></P> <P> <UL> <LI> Generation of TCGA Clinical Data Resource for 11,160 patients over 33 cancer types </LI> <LI> Analysis of clinical outcome endpoints with usage recommendations for each cancer </LI> <LI> Demonstration of data validity and utility for large-scale translational research </LI> </UL> </P> <P><B>Graphical Abstract</B></P> <P>[DISPLAY OMISSION]</P>
( Michelle A. Phipps ),( Andrew F. A. Hoadley ) 한국화학공학회 2003 Korean Journal of Chemical Engineering Vol.20 No.4
Heat integration techniques can be used to optimize the energy requirement for both new and retrofit plant designs. Software tools for identifying retrofit options are becoming available. This paper reports our experiences from using heat exchanger network (HEN) optimization software for a retrofit case study of an oil refinery process. The HEN optimization software was used to automate the search for the most beneficial retrofit designs following the twostage process proposed by Asante and Zhu. The software provided three potential retrofit designs. Results from this analysis were used as the basis of a rigorous mass and energy balance simulation of the plant. The simulation corroborated the energy savings, but there were some important differences. The simulation required 20% more heat exchange area. Furthermore, the retrofit design involving one topology change was shown to be less economic than an alternative design. These differences are discussed and a revised methodology is proposed.
( Adrian L. Querzoli ),( Andrew F. A. Hoadley ),( Tony E. S. Dyson ) 한국화학공학회 2003 Korean Journal of Chemical Engineering Vol.20 No.4
This study investigates improving the energy efficiency of two key refining processes: the Crude Distillation Unit (CDU) and the Residue Cracking Unit (RCU). The research methodology followed the ‘targeting before design’ approach. The CDU is a ‘tightly pinched’ system, with limited opportunities for further energy savings. The RCU actual △T_(min) is around 55℃ indicating a low level of current heat recovery. The Total-Site analysis shows that theoretically 18MW of heat could be transferred from the RCU to the CDU, reducing CDU requirements by 40% for a new or grass roots design. RCU retrofit designs were developed to increase steam generation by up to 35% and in line with targeting estimates would appear to have economic potential. The alternative CDU-RCU retrofit design was developed to decrease CDU hot utility use. Although the Total-Site profile demonstrated strong potential for heat integration, this retrofit design is not commercially attractive, as the decrease in CDU fuel does not offset the cost of reduced steam generation. This demonstrates the need to consider the different fuel and steam costs in the Total-Site analysis.