http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
자동차 실내 인화성물질과 전기과부하에 의한 화재관련 사례 연구
한재오(Jae Oh Han),함성훈(Sung Hoon Ham),임하영(Ha Young Lim),이일권(Il Kwon Lee) 한국가스학회 2014 한국가스학회지 Vol.18 No.3
이 논문은 자동차 실내의 인화성 물질과 전기적인 접촉 불량에 의한 화재사례를 분석하고 연구하는 것이다. 첫 번째 사례는 운전자가 에어컨 냄새 탈취제인 방향제를 사용 후 실내의 크래쉬 패드에 두고 내린 것이 외부의 복사열에 의해 폭발하면서 화재가 발생된 것으로 확인되었다. 두 번째 사례는 운전자가 자동차 실내에 전자기기 등을 사용하면서 전기적인 과부하가 걸려 단락현상에 의해 화재가 발생된 것으로 확인되었다. 세 번째 사례는 자동차 내부의 시트를 따뜻하게 하기 위해 열선을 설치하였다. 초기에 설치하였을 때는 화재의 위험성이 약했으나 5,000km를 운행하면서 이 열선의 내구성이 떨어지면서 순간적으로 전기적인 과부하가 발생되었고, 이 열이 시트에 옮겨 붙으면서 자동차 화재가 발생된 것으로 확인되었다. 네 번째 사례는 뒷좌석에 있던 승객이 담배를 피우던 중 완전히 소화하지 않은 상태로 둔 것이 가연성 종이에 옮겨 붙어 자동차가 전소된 것으로 확인되었다. 따라서, 실내의 인화성 물질이나 전기적인 시스템을 추가로 사용할 때는 화재가능성을 최대한 고려하고 이에 대한 세심한 대책을 강구하여야 한다. This paper is to analyze and study the failure examples of fire by inflammables and electric contact faulty in interior of vehicle. The first example, the driver used to air freshener that remove the air conditioner bad smell. He get out of a car. And then, he put it on the crash pad . Before long, a fire breaks out because of explosion solar radiation. The second example, the driver used in room of a car. It certified the fire by disconnection phenomenon happened the electric overload. The third example, the driver install the heat rays to warm his body, In the initial stages, it didnt seek the dangerous of fire during using a car to 5,000km. This heat rays become to down durability so that produced the electric overload in an instant. The fourth example, after the man smoked the cigarette on riding with rear seat, he put it on seat in vehicle no extinguishing the burning cigarette . It knew the fact that burnt to ashes a car by on well combustible paper. Thus, the driver must consider a countermeasure for minimize the fire production when he use the inflammable and install adding electric system.
디젤엔진 자동차의 EGR 및 공기 제어와 CPF 장치에 관련된 고장사례 고찰
이일권(IL Kwon Lee),국창호(Chang Ho Kook),함성훈(Sung Hoon Ham),이영숙(Young Suk Lee),염광욱(Kwang Wook Youm),유창배(Chang Bae You),김성모(Sung Mo Kim),임하영(Ha Young Lim),안호철(Ho Cheol Ahn),이정호(Jeong Ho Lee) 한국가스학회 2018 한국가스학회지 Vol.22 No.2
이 논문은 디젤엔진 자동차의 EGR 및 공기 제어와 CPF 장치에 관련된 고장사례 연구이다. 첫 번째 사례는 엔진진공펌프 손상으로 인해 엔진오일이 EGR 밸브 내부 다이어프램 손상으로 인해 오일이 흡기로 유입되어 연소실로 들어가 불완전 연소함으로써 배기할 때 매연이 발생된 것으로 확인되었다. 두 번째 사례의 원인은 공기제어 장치인 스로틀 플랩(throttle flap)을 점검하였을 때 스로틀 플랩이 고착되어 흡입공기량 부족에 의해 매연이 발생된 것을 확인하였다. 세 번째 사례는, 배기가스 온도센서의 불량으로 인해 온도를 감지하지 못해 재생기능이 되지 않아 매연이 발생된 것으로 확인되었다. 따라서, 배기가스발생으로 인한 환경오염 문제가 발생하지 않도록 최적의 상태를 유지하도록 관리하여야 한다. The purpose of this paper is to study for failure examples of emission gas recirculation and air control and catalyzed particulate filter system in diesel engine vehicle. The first example, the researcher found the fact that the much engine oil came into the intake manifold causing diaphragm damage of EGR valve. The engine oil entered into combustion chamber of engine so that a car emit the polluted exhaust gas when driving. The second example, the researcher certified the sticking phenomenon of carbon and foreign substance with the throttle flap so that the exhaust fumes discharged exhaust port. The third example, the regeneration function don’t activated to not detect the temperature of exhaust gas because of damage in the sensor. Thus, the researcher must meticulously manage his car not in order to take place the problem of environmental pollution.
승용자동차 전자제어 에어컨 장치의 다이오드, 써모센서와 배선단락에 대한 고장사례 고찰
이일권(IL Kwon Lee),국창호(Chang Ho Kook),함성훈(Sung Hoon Ham),이정호(Jeong Ho Lee),문학훈(Hak Hoon Moon),유창배(Chang Bae You),황한섭(Han Sub Hwang),임춘무(Chun Moo Lim),정동화(Dong Hwa Jung),나윤환(Yun Whan Na) 한국가스학회 2017 한국가스학회지 Vol.21 No.5
이 논문은 자동차의 전자제어 에어컨에서 발생하는 고장사례에 대한 논문이다. 첫 번째 사례에서, 원인은 에어컨 릴레이 내부에 서지 전압 역류 방지용으로 사용된 다이오드가 에어컨이 OFF 되었을 때 다이오드의 단락으로 인해, 서지 전압을 흡수하지 못해 퓨즈가 반복적으로 끊어진 것을 확인하였다. 두 번째 사례에서, 원인은 핀 써모센서 내부의 단선으로 인해 에어컨을 제어하지 못함으로써 이베퍼레이터의 동결현상이 발생한 것을 확인하였다. 세 번째 사례에서, 원인은 운전석 앞쪽의 크래쉬 패드 하단에 있는 와이어링의 에어컨 핀센서 핀과 연결되는 배선이 차체와의 간섭으로 인해, 피복이 벗져져 단락(short)현상에 의해 에어컨 스위치와 핀센서가 소손되어 에어컨이 작동하지 않는 것을 확인하였다. 따라서, 이러한 고장 현상을 철저하게 확인하고 개선하여 최적의 시스템을 유지할 수 있도록 하여야 한다. The purpose of this paper is to study for a failure examples producing in electronic control air conditioner in vehicle. The first example, it looked for the repetitive fuse cutting phenomenon that the diode using for a surge voltage prevention of inner A/C relay damaged because of no absorbing the surge voltage by short of diode when the A/C is off. The second example, it knew the icing phenomenon of evaporator that the A/C ECU didn’t control the A/C because of inner cutting of fin thermo sensor. The third example, it verified the operation trouble phenomenon because of the A/C switch and for sensor burned in flames by short phenomenon when the sheath of the cable has peeled off. Therefore, the driver have to manage the optimism system of a car by thoroughgoing inspection and improvement the failure phenomenon.
자동차용 LPG 엔진의 점화플러그 장착 부 손상, 점화시기 조정불량, 흡입밸브 부 이물질유입 고장사례 연구
이일권(IL Kwon Lee),국창호(Chang Ho Kook),함성훈(Sung Hoon Ham),김성모(Sung Mo Kim),황한섭(Han Sub Hwang),정동화(Dong Hwa Jung),문학훈(Hak Hoon Moon),이정호(Jeong Ho Lee) 한국가스학회 2021 한국가스학회지 Vol.25 No.2
이 논문은 LPG 자동차용 엔진의 고장사례를 연구하여 자동차 생산에 활용함이 목적이다. 첫번째 사례는 엔진의 실린더헤드를 분해하여 확인한 결과 실린더 헤드의 점화플러그가 조립되는 나사부 마멸때문에 점화플러그의 불꽃이 누설되어 출력이 떨어지면서 엔진의 부조화 현상이 가끔 유발되는 것을 발견하였다.. 두 번째 사례는 캠샤프트의 위치와 크랭크 샤프트 위치를 맞춘 타이밍 마크가 0.5칸 틀어져 엔진의 부조화 현상이 발생된 것을 확인되었다. 세 번째 사례는 실린더 헤드를 분해하여 확인한 결과, 실린더 헤드에 제거되지 못한 이물질이 3번 흡기포트에서 공기 흐름에 따라 이동하다가 흡기밸브의 닫힘시기를 원활하지 못하여 하여 고장이 발생된 것을 확인하였다. 따라서, 자동차 관리자는 철저하게 점검해야 하고, 자동차 생산자는 철저한 품질확보를 통해 고장의 원인을 제거해야 할 것으로 판단된다. This paper is a purpose to study the failure examples for LPG vehicle. The first example, the researcher certified the incongruity phenomenon decreased engine power by ignition fire leakage because of spark plug threaded part damage assembling in cylinder head. The second example, the timing mark that accurately adjusting the camshaft and crankshaft position were twisted about 0.5 block each other. Finally, the researcher seeked the disharmony phenomenon as it couldn‘t set ignition timing. The third example, the researcher knew the failure phenomenon by interrupted the closing period for intake valve moving with air flow in the number 3 port of cylinder head as the foreign substance in cylinder head didn’t remove. Therefore, the manager of a car has to thorough going inspect and the manufacture of a car must remove the cause of failure with quality assurance.