http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
펨토셀 주파수 신호 생성을 위한 IEEE 1588 기반 클록 동기화 시스템의 설계
한지호(Han, Jiho),박용재(Park, Yong-Jai) 한국산학기술학회 2015 한국산학기술학회논문지 Vol.16 No.7
본 논문은 펨토셀에서 요구되는 정확한 주파수 신호 생성을 위한, IEEE 1588 기반의 클록 동기화 회로 및 시스템을 제시한다. 동작 검증 및 성능 평가를 위한 프로토타입 보드와 실험 환경에 대하여 설명하고, 실험 결과가 펨토셀 동기화에 적합함을 확인한다. 펨토셀은 설치 위치의 제약이 없는 저가의 장비로 개발해야 하기 때문에, IEEE 1588 동기화 시스템의 실제 구현에 관한 연구가 매우 중요하다. 제안하는 동기화 회로를 내장한 펨토셀 기지국을 FPGA 보드에 프로그램하고, 그 기지국들의 네트워크에서 실험한 결과 -16 ~ 9 ns 이내의 동기화 오차를 보장함을 관찰하였고, 이는 3GPP의 HNB 동기화 기준을 만족하는 수준임을 확인할 수 있다. This article presents a circuit and a system for IEEE 1588 based clock synchronization to generate a very accurate frequency signal required in femtocell devices. A prototype board and the experimental environment to verify the functions and to evaluate the performance are explained to verify the feasibility of the proposed synchronization system. To make low-cost femtocells without constraints on the place of installation, it is very important to study on the practical implementation of synchronization system based on IEEE 1588. The experimental result shows that the synchronization errors between -16 ns and 9 ns are guaranteed over the network of femtocell devices with the proposed synchronization circuits, thus the synchronization criteria of the 3GPP HNB are met.
변수변화에 따른 가변강성 메커니즘의 강성변화 경향성에 관한 연구
함기범(KiBeom Ham),한지호(Jiho Han),전종균(JongKyun Jeon),박용재(JongKyun Jeon) 한국산학기술학회 2016 한국산학기술학회논문지 Vol.17 No.6
일반적으로 시스템을 강성체로 설계할 경우 시스템의 구조적 안정성을 확보할 수 있으나 유리잔을 잡거나 작은 수술 용 도구로 사용하는 등의 사용용도에 따라 활용성이 제한될 수 있다. 이러한 문제를 해결하기 위하여 유연한 재질을 사용하여 강성조절이 가능한 메커니즘에 대한 연구가 다양하게 이루어져 왔다. 기존에 연구했던 강성체와 연성체의 연속구조로 이루어 진 모델에 텐던을 삽입한 구조를 이용한 가변강성 메커니즘을 통하여 가변강성 구조체에 대한 가능성을 확인하였다. 그러나 필요로 하는 가변강성을 충족하기 위한 구조체의 설계 변수에 대한 연구가 필요하였다. 따라서 본 연구에서는 가변강성 메커 니즘의 다양한 변수 변화에 따른 강성변화 실험을 통해 강성의 경향성을 파악하고자 하였다. 실험 결과 지름이 클수록 강성은 증가하며 강성의 증가폭 또한 늘어난다. 또한 연성체 길이가 짧을수록 강성이 증가하며 텐던을 당겨 연성체를 압착할 경우 강성값은 비선형적으로 증가하였다. 동일 조건에서 연성체 길이변화에 따른 강성 증가폭과 강성체의 길이 변화에 따른 강성 증가폭을 비교하였을 때 연성체 길이 변화가 강성체 길이 변화 보다 강성값 변화에 영향을 미친다는 것을 확인하였다. 또한, 해석값이 실험값에 비하여 정확성은 낮지만, 가변강성의 경향성을 확인하기 위하여 해석적인 방법을 통한 강성을 예측해보았 다. 이러한 변수변화 실험 결과는 필요로 하는 강성값을 충족하는 가변강성 메커니즘 설계에 활용할 수 있을 것이다. In general, a system can be stable when it is designed with a rigid material. However, the use of a rigid system can be limited, such as grasping a glass or using a small surgical instrument. To resolve this limitation, a variable stiffness mechanism was developed using a flexible material. Previous research verified the variable stiffness mechanism where flexible segments and rigid segments were connected alternately in series. However, research into the design parameters of the variable stiffness structure is needed to satisfy the desired stiffness. Therefore, a variable stiffness structure was tested by varying the design parameters to confirm the trend of the stiffness variation. When the radius of the structure becomes larger, the stiffness increases. The stiffness increased with decreasing length of the flexible segments. Under the same design parameters, the length of the flexible segments had a greater effect on the stiffness than the length of the rigid segments. In addition, the stiffness was estimated using the pseudo rigid body model and was compared with the experimental results. This parametric study can be used as a design guideline for designing the variable stiffness mechanism to satisfy the desired stiffness.