http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
충격보강제의 함유량과 분산이 나일론 6 복합체의 충격강도에 미치는영향의 컴퓨터 해석
우정우 ( Jeong Woo Woo ),류민영 ( Min Young Lyu ) 한국고무학회 2014 엘라스토머 및 콤포지트 Vol.49 No.4
고분자 소재는 금속 소재에 비해 기계적 강도, 특히 충격강도가 매우 취약하기 때문에 이의 증대를 위해 충격보강제를 이용하는 경우가 많다. 이러한 충격강도는 충격보강제의 함량과 분포에 따라 변화한다. 본 연구에서는 충격보강제가 함유된 나일론 6 시편에 대해서 충격시험을 모사하였고 충격시편 단면에서의 응력분포를 통해 충격강도 증대원리를 관찰하였다. 시편 단면에서 충격보강제의 개수와 분포에 따른 해석을 하여 비교하였다. 충격보강제의 개수가 증가할수록 부피가 감소하는 모델의 경우 놋치 표면의 응력과 주응력의 크기가 점차 높게 나타났다. 충격보강제의개수가 증가할수록 충격보강제 전체의 총 표면적이 증가하는 모델의 경우에는 응력과 주응력이 점차 높게 관찰되었다. Polymer has low mechanical strength than metal. In particular, the impact strength is very weak. Impact modifier reinforced polymers are frequently used. Impact strength of reinforced polymer is changed according to content and distribution of impact modifier. In this study, izod impact test has been simulated to analyze the mechanism of impact odifier reinforced Nylon 6. Computational results were compared for numbers and distributions of impact modifier. As the total volume of rubber particles decreased, the stress at the notch increased for the simulation model that the volume decreases as particle number increases. As the surface area of particle sphere increased, the stress and difference of principle stress increased for the simulation model that the total surface increases as particle number increases.
슬롯코팅에서 정상 및 비정상상태 컴퓨터해석을 통한 코팅의 균일성 분석
우정우(Jeong Woo Woo),성달제(Dal Je Sung),류민영(Min Young Lyu) 한국고분자학회 2014 폴리머 Vol.38 No.5
평판 디스플레이 제조공정 중의 하나인 유리기판 위에 감광액을 도포하는 과정에 슬롯코팅 방법이 많이 쓰이고 있다. 도포공정에서는 균일한 코팅 두께를 얻는 것이 중요하며, 코팅의 균일성은 노즐방향과 운전방향의 균일성으로 나뉜다. 운전방향의 코팅 균일성은 코터의 운전조건에 영향을 받고, 노즐방향의 균일성은 다이 내부의 흐름의 균일성에 영향을 받게 된다. 이러한 영향 인자들로 인해 코팅두께가 불균일한 현상이 발생하는데, 코터 진행의 초기구간에는 비정상상태 구간으로 운전방향과 노즐방향으로 코팅두께가 균일하지 않다. 본 연구에서는 이러한 현상이 나타나는 원인을 파악하기 위해 비정상상태와 정상상태를 구별하여 해석하고 이를 실험과 비교하였다. 그 결과 감광액이 다이 내부에서 균일한 압력분포에 도달하기까지 시간이 필요하고 이로 인해 코팅 초기구간에서 다이의 양가장자리 영역의 속도가 중앙 영역에 비해 속도가 낮게 나타났으며 코팅 두께도 얇게 나타났다. 그러나 정상상태에 도달한 후에는 가장자리 영역의 속도가 중앙 영역보다 높게 나타났고 코팅 두께 역시 두껍게 나타났다. As a process of plat panel display production, slot coating is widely used for the coating of photoresist on awide glass substrate. A uniform coating thickness is important, and the coating uniformity is divided into nozzle and machine directions. The machine and nozzle directions coating uniformities are influenced by the operation condition of coater and flow uniformity inside the die, respectively. Non-uniform coating during steady coating process occurs according to those factors, however, non-uniform coating along the machine and nozzle directions has been observed at the beginning of coating by unsteady flow. In this study, steady and unsteady state flow simulations have been performed and compared with experiment to examine the causes of non-uniform coating. Computational results exhibited that it tooka time to get a uniform pressure distribution at whole inside the die, and during this period of time edge regions showed lower exit velocity compared with center region. Subsequently edge regions had thinner coated layers than center region. However edge regions showed higher exit velocity than center region after steady state, and this made edge regions had thicker coated layer than center region.
투명 사출품에서 성형조건에 따른 복굴절 및 잔류응력의 분석
우정우(Jeong-Woo Woo),홍진수(Jin-Su Hong),김현구(Hyun-Ku Kim),류민영(Min-Young Lyu) 한국고분자학회 2016 폴리머 Vol.40 No.2
사출성형품에 형성된 잔류응력은 시간이 지남에 따라 제품에 변형이나 휘어짐을 일으키고 투명한 제품의 경우 복굴절을 일으킨다. 사출성형 중에 형성되는 잔류응력은 성형온도, 금형온도, 냉각조건, 보압조건과 같은 사출성형 조건에 의해 다르게 나타난다. 잔류응력의 측정방법 중 광탄성을 이용한 측정법은 다른 방법들에 비해 간편하고 쉽게 측정할 수 있는데 투명한 제품에만 적용이 가능한 방법이다. 복굴절 분포와 잔류응력의 크기를 PC, PS, 그리고 PMMA를 이용한 사출성형 시편을 통해 연구하였다. 그리고 컴퓨터 시뮬레이션을 통해 복굴절 패턴을 모사하고 실험결과와 비교하였다. PS 시편은 가장 높은 복굴절을 나타냈고 PMMA는 가장 낮은 복굴절을 보였다. 제품의 잔류응력은 게이트 근처에서 가장 컸고 게이트에서 멀수록 작았다. 사출성형에서 냉각시간이 길고, 사출온도가 높고, 보압시간이 길수록 제품 내에 잔류응력은 줄어들었다. Residual stresses are developed during injection molding process and these cause a warpage and invoke a birefringence in a molded article. The levels of residual stresses are dependent of molding conditions, such as melt temperature, mold temperature, cooling condition, and packing condition. Among the residual stress measurement methods, the photoelasticity method is simple and convenience to measure compared with other methods. However this method can be utilized only for a transparent product. Birefringence and residual stress have been observed in injection molded polycarbonate (PC), polystyrene (PS), and polymethylmethacrylate (PMMA) specimens according to injection molding conditions. Computer simulation has been performed and compared with experimental observation of birefringence. PS specimen showed the highest birefringence whereas PMMA showed the lowest birefringence among them. Locations close to the gate showed higher residual stress than locations far from the gate. Long cooling time, high injection temperature, and long packing time reduced residual stress.
Tolosa-Hunt Syndrome으로 인한 통증성 안구운동 장애 치험 1례
정윤경,우지명,강아름,조기호,문상관,정우상,Jeong, Yun-Kyeong,Woo, Ji Myung,Kang, A-reum,Cho, Ki-ho,Mun, Sang-Kwan,Jung, Woo-sang 대한중풍순환신경학회 2015 대한중풍.순환신경학회지 Vol.16 No.1
■ Objectives The purpose of this clinical study is to evaluate the effect of Traditional Korean Medicine(KM) on a patient with Tolosa-Hunt syndrome. ■ Methods We treated a 58 years old male patien t with Tolosa-Hunt syndrome who had several clinical symptoms such as ocular pain, limitaion of ocular movement and unilateral ptosis. We used herbal medication, acupuncture, electro-acupuncture(EA), cupping, moxibustion, bee-venom injection. Then we evaluated the improvement by Numerical Rating scale(NRS), Distance of eye opening and ratio of pupil movement. ■ Results We demonstrated the decrease of pain score and improvement of equal ocular movement(EOM) and ptosis after the KM treatment. ■ Conclusion This study proved the effect of KM treatment on Tolosa-Hunt syndrome. It could cooperative treatment would be more effective than mono treatment of western medicine.
손정화,박민정,우지명,조기호,문상관,정우상,Son, Jeong Hwa,Park, Min-jeong,Woo, Ji-myung,Cho, Ki-ho,Mun, Sang-Kwan,Jung, Woo-sang 대한중풍순환신경학회 2016 대한중풍.순환신경학회지 Vol.17 No.1
■ Objectives A case of a 44 years old Korean female with left side headache due to Transformed migraine is presented. ■ Methods He was treated with electroacupuncture around eyes and dry cupping on shoulder, moxibustion, acupuncture and herbal medicine, Chai Ling Tang. Then we evaluated the improvement by Pain area comparison and Numerical Rating Scale(NRS). ■ Results Headache was improved after the administration of Korean medical treatments. ■ Conclusion Korean medical treatment may be effective in treating headache due to Transformed migraine.