http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
심성훈,조상준,김광영,Sim, Seong-Hun,Jo, Sang-Jun,Kim, Gwang-Yeong 한국기계연구원 1989 기계연구원소보 Vol.19 No.-
To investigate design factors of dilution ventilation system, numerical analysis of air contamination flow and concentration distribution have been made, by using the low Reynolds number turbulent model. And flow visualization and measurement of particle concentration for that model also have been made. By comparing of these results we have secured the essential data for the adequate counterplan of dilution ventilation system. The results of this study are as follows: 1) Inlet should be located near the wall for the prevention of the formation of the recircula¬tion zone. 2) In case of natural exhaust, air contamination flow is driven to the far outlet from the inlet. 3) It is favorable for dilution to make turbuence as much as possible.
김광영,조상준,심성훈,고득용,Kim, Gwang-Yeong,Jo, Sang-Jun,Sim, Seong-Hun,Go, Deuk-Yong 재료연구소 1990 機械와 材料 Vol.2 No.1
국내산업계의 기술이 전반적으로 일본 기술을 답습하고, 이를 극복하고자 노력하는 상황이 공기조화설비분야에서도 예외는 아니다. 따라서 수년전의 일본 공조설비분야의 현황을 살펴보는 의미로 일본공기조화 위생공학회지 제61권 10호에 실린 "공조설비분야에 있어서 연구.개발의 동향"을 발췌하여 정리함으로써 국내의 공기조화분야가 나아갈 방향에 대한 참고자료로 삼고자 하였다.
IMT-2000용 초소헝 적층형 대역 통과 칩 필터 설계 및 제작
임혁,하종윤,심성훈,강종윤,최지원,최세영,오영제,김현재,윤석진,Lim Hyuk,Ha, Jong-Yoon,Sim, Sung-Hun,Kang, Chong-Yun,Choi, Ji-Won,Choi, Se-Young,Oh, Young-Jei,Kim, Hyun-Jai,Yoon, Seok-Jin 한국세라믹학회 2003 한국세라믹학회지 Vol.40 No.10
BiN $b_{0.975}$S $b_{0.025}$ $O_4$저온 동시 소결 세라믹 후막 및 적층 세라믹(Multi-Layer Ceramic, MLC) 공정 기술을 이용한 소형 마이크로파 필터를 설계 및 제작하였다. MLC 칩 대역 통과 필터(BPF)는 소형화와 낮은 가격이라는 장점을 가지고 있다. 제안된 필터는 stripline 공진기와 결합 캐패시터로 구성되며, IMT-2000용 단말기의 수신단 통과 대역에 적합하며 통과 대역 아래쪽 저지 대역에 감쇠극이 형성되도록 설계하였다. 상용 마이크로파 회로 및 구조 설계 tool를 이용하여 제안된 MLC칩 대역 통과 필터의 공진기 전자기적 결합량 변화 및 결합 캐패시턴스에 따른 필터의 주파수 특성, 특히 감쇠극의 위치 변화에 대해 살펴보았다. 제작된 MLC 칩 BPF의 주파수 특성은 시뮬레이션 결과와 매우 일치하였다. A Multi-Layer Ceramic (MLC) chip type Band-Pass Filter (BPF) using BiNb$\_$0.975/Sb$\_$0.025/ $O_4$ LTCC (Low Temperature Co-fired Ceramics) and MLC processing is presented. The MLC chip BPF has the benefits of low cost and small size. The BPF consists of coupled stripline resonators and coupling capacitors. The BPF is designed to have an attenuation pole at below the passband for a receiver band of IMT-2000 handset. The computer-aided design technology is applied for analysis of the BPF frequency characteristics. The attenuation pole depends on the coupling between resonators and the coupling capacitance. An equivalent circuit and structure of MLC chip BPF are proposed. The frequency characteristics of the manufactured BPF is well acceptable for IMT-2000 application.
장광호(Kwang-Ho Jang),김보기(Bo-Ki Kim),최진주(Jin-Joo Choi),최흥식(Heung-Sik Choi),심성훈(Sung-Hun Sim) 한국전자파학회 2018 한국전자파학회논문지 Vol.29 No.2
본 논문은 마그네트론 대체를 위한 반도체 전력 발진기 모듈 설계에 관련된 내용을 기술하였다. 300급 LDMOS 단일 전력 증폭기의 특성을 확인하였고 두 개를 결합하여 모듈을 구성하였다. 결합된 모듈에 delay-line feedback loop을 구성하고 위상 천이기를 이용하여 위상을 조절하여 발진기를 구동시켰다. 발진기 모듈 측정 결과 주파수 2.327 ㎓에서 출력 800 W, 효율 58 %로 측정되었다. 이 결과는 시뮬레이션 결과와 유사한 특성을 보여준다. This paper presents a design study of a solid state power oscillator to replace the conventional magnetron. The operational conditions of a single-stage 300 W LDMOS power amplifier were fully characterized. The power module consisted of two amplifiers connected in parallel. A delay-line feedback loop was designed for self-oscillation. A phase shifter was inserted in the delay-line feedback loop for adjusting the round-trip phase. Experiments performed using the power oscillator showed an output power of 800 W and a DC-RF conversion efficiency of 58 % at 2.327 ㎓. The measured results were in good agreement with those predicted by numerical simulations.