http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
초점보정 렌즈설계 및 3D 프린터 이용 가공 특성평가(I)
신현명,윤성철,최해운 한국기계가공학회 2015 한국기계가공학회지 Vol.14 No.4
A focal length-correcting lens called the F-theta lens is required to compensate for the different focus on spot size due to the deflected incident laser beam. The F-theta lens was designed by the ray tracing method and fabricated by a 3D printer with polymer-based material. The designed F-theta lens is able to compensate for the focus on spot size by an incidence angle of 0 to 2 degrees. Based on the analysis of the simulation, there was almost no aberration in the 0° incidence angle, and the maximum of 50μm of aberration was observed at the incidence angle of 2°. Diffraction-encircled energy was analyzed to characterize the designed optics, and an image simulation was performed to confirm the actual image resolution.
Expert System을 이용한 치공구설계용 Representation Scheme에 관한 연구
신현명 啓明大學校 産業技術硏究所 1997 産業技術硏究所 論文報告集 Vol.19 No.2
치공구는 생산 및 제조에서 가공 및 조립공정에서 없어서는 안되는 필수적인 공구이다. 치공구의 설계는 부품의 외형, 재질, 제조방법, 및 가공순서 등이 결정된 이후에 시작하게 된다. 따라서 신속한 제품개발 및 생산을 요하는 현 생산체제에서는 병목과정이 될 수밖에 없다. 또한 CAD, CAE, CAM등의 기술로 많은 시간을 단축시켰으나 공학이라기보다는 기술에 가까운 치공구의 설계만은 아직도 경험이 많은 기술자가 설계를 맡고 있다. 따라서 현재도 가장 어려운 절차중의 하나이다. 새로 각광을 받고 있는 전문가시스템은 이 설계절차를 단축시키고 비전문가도 치공구설계가 가능하도록 해줄 수 있다. 본 연구에서는 치공구설계용 전문가시스템을 개발하는데 가장 중요한 요소중의 하나인 Representation Scheme의 개발과 고려해야할 사항을 정립시켰다. 단순 입방체의 조합을 이용하는 이 Representation Scheme은 가공물의 형상은 물론 치공구 설계시에 고려해야할 많은 사항들에 대한 정보도 내포할 수 있다.
신현명 계명대학교 산업기술연구소 1993 産業技術硏究所 論文報告集 Vol.16 No.1
본 논문은 선형계획법을 이용하여 FMS를 구성하는 여러대의 CNC공작기계 작업량의 균형을 맞추었을 때 FMS의 효율에 미치는 효과를 시뮬레이션을 통하여 연구한 결과이다. CNC공작기계의 가공량의 균형을 맞추는 방안은 본래계획 되어 있는 공작기계 이외의 공작기계로 가공시킴으로서 한 공작기계의 가공량을 성능이 다소 떨어지는 대체 공작기계에 맡김으로서 성취할 수 있다. 본 연구에서는 FMS의 전산 제어체계를 이용하여 운영할 수 있는 방안을 창안하여 기본적인 운영방법과 비교함으로서 가공량의 균형을 맞춘 분배가 미치는 영향을 검토하였다. 시뮬레이션 연구결과 공작기계들간의 가공량의 균형을 맞춤으로서 종래의 운영방법과 비교했을 때, 총가공시간(Cycle Time)이 현저하게 줄었을 뿐 아니라 고가인 공작기계의 사용시간(Machine Utilization)을 증가시킬 수 있다는 것이 밝혀졌다.
임문혁,신현명 啓明大學校 産業技術硏究所 1997 産業技術硏究所 論文報告集 Vol.19 No.2
Stress of a caliper brake predesigned by a domestic company are analyzed by ABAQUS utilizing the finite element method. The analysis was perfomed in two parts-first the cylinder block and then the carrier block. The value of the von Mises equivalent stress at some portions of the break turned up to over the yield stress of cast iron. The critical area of the originally designed model was examined. It was found that the von Mises values stress values at the critical weak point of carrier block decreased considerably after it was redesigned.
신현명,임문혁 啓明大學校 産業技術硏究所 1997 産業技術硏究所 論文報告集 Vol.20 No.-
It is crucial for the safety of the passengers to design the brakes of the vehicle appropriately. One must accurately estimate the temperature increase of the brake during the braking operation and provide sufficient cooling or heat loss to maintain the stress below the allowable limit of the braking system. In this study three models were used to obtain the temperature distribution during the braking process of an actual part was investigated and compared. A two-dimensional axi-symmetric model was sufficient for obtaining the temperature distribution; however, it was found to be unsatisfactory for analyzing the stresses. In the case of the tree-dimensional portion of the model the temperature distribution turned out to be similar to the actual temperature measurement. However, under repeated braking conditions the maximum equivalent stress turned out to be greater that the yield stress; thus, the current design requires research.