http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
배지열(Ji-Yeul Bae),박슬기(Sulki Park),김태환(Taehwan Kim),송지운(Jiwoon Song),함희철(Heecheol Ham),배주찬(Ju Chan Bae),조형희(Hyung Hee Cho) 한국추진공학회 2012 한국추진공학회 학술대회논문집 Vol.2012 No.11
로켓 설계에서 내열 설계는 공력 설계와 더불어 매우 중요하다. 내열 설계에 있어 노즐 표면에 임무 시간동안 노즐형상을 유지할 수 있는 내열재를 추가하게 되는데 이때 내열재의 추가는 시스템 중량을 상승시켜 성능 하락을 유발할 수 있다. 따라서 내열재를 적절하게 설계해 노즐에 적용하는 것이 중요한데 이를 위해서 내열재의 정확한 물성을 아는 것이 매우 중요하다. 이때 가장 중요한 물성이 열분해율을 결정하는 열반응상수와 활성화에너지이다. 따라서 본 연구에서는 탄소/페놀릭 내열재의 열반응상수를 측정하는 실험을 진행하였다. 아음속에서 소형 모터를 이용해 실험한 온도 분포로 열반응상수를 역으로 도출하였고 이는 선행 문헌의 결과와 유사하였다. In rocket design process, thermal design is one of the most important aspect. In order to protect nozzle, adequate amount of heat protection material is added to nozzle for required mission time. However adding heat protection material increase the system weight and reduce overall performance. Therefore optimization of heat protection material is important and it requires accurate properties of heat protection material. Among the properties of materials, kinetic constant and activation energy that govern decomposition process are the most important. Thus kinetic constant measurement is done with small test motor experiment in subsonic region.
이차분사노즐 작동 조건 변화에 따른 SITVC 성능해석
배지열(Ji-Yeul Bae),송지운(Jiwoon Song),김태환(Taehwan Kim),조형희(Hyung Hee Cho),배주찬(Ju Chan Bae) 한국추진공학회 2011 한국추진공학회 학술대회논문집 Vol.2011 No.11
SITVC 시스템의 이차분사 노즐 분사 조건 변화에 따른 시스템 성능 변화를 수치적으로 연구하였다. 해석에 사용된 형상은 3차원 종형 수축-팽창 노즐이고 측면에 8개의 이차분사 노즐을 가진다. 노즐 내부 유동은 전압이 70bar이며 300K의 cold flow로 가정하였다. 이차 유동의 유량 변화와 노즐 작동 조건 변화를 고려하였다. 상용코드인 Ansys Fluent v.13을 통해 해석하였고, 난류모델은 Spalart-Allmaras model(1- equation)를 사용하였다. 충격파의 수치적 진동을 막고 충격파의 불연속성을 잘 해석하기 위해 AUSM+ scheme을 사용하였다. Axial thrust, side force, system specific impulse ratio 와 같은 성능 변수를 사용해 시스템 성능을 평가하였다. Performance of Secondary Injection Thrust Vector Control system is investigated under various secondary injection operating conditions. 3-dimensional converging-diverging nozzle having 8 secondary injection nozzles is used in this numerical study. Total pressure of flow inside the nozzle is about 70bars, and total temperature set to 300K for cold flow simulation. Effect of secondary injection flow rate and injection nozzle configuration is considered in this research. Simulation is conducted with commercial CFD code Ansys Fluent v13. Spalart-Allmaras(1-equation)model is used for turbulence modeling with AUSM+ scheme. Various performance factors as Axial thrust, side force, system specific impulse ratio are considered and explained for system performance evaluation.
유한요소해석을 통한 쿼츠/페놀릭 5매 주자직 재료의 비등방 열전도도 평가
배형모(Hyung Mo Bae),배지열(Ji-Yeul Bae),배주찬(Ju Chan Bae),조형희(Hyung Hee Cho) 한국추진공학회 2016 한국추진공학회 학술대회논문집 Vol.2016 No.5
섬유 복합재는 열전도도가 서로 다른 섬유와 충전제로 구성되어 있고, 이에 의해 비등방 열전도도를 지닌다. 비등방 열전도도는 소재의 설계에 있어 중요한 물리적인 특성으로, 수치해석을 통한 비등방 열전도도의 예측이 필요하다. 본 연구는 비등방 열전도도를 예측하는 해석기법을 확립하고, 기존에 공개되어있지 않은 쿼츠/페놀릭 5매 주자직의 열전도도를 도출하였다. 해석기법을 확립하기 위해 공개되어 있는 탄소/에폭시 평직 복합재의 열전도도의 실험값과 유한요소해석 결과와의 비교 검증을 수행하였고 유한요소해석 결과는 실험결과가 잘 일치함을 확인하였다. 검증된 유한요소해석 기법을 이용하여 실제 레이돔 제작에 사용되는 쿼츠/페놀릭 5매 주자직의 비등방 열전도도를 예측하였고, 섬유체적비가 복합재의 면외 방향 열전도도에 미치는 영향을 평가하였다. Fiber composites are composed of fiber and matrix, and it causes orthogonal thermal conductivity of materials. Evaluation of orthogonal thermal conductivity is important research with respect to thermal design of materials. The purpose of this study is to establish finite element method to expect orthogonal conductivity of fiber composite and to evaluate orthogonal conductivity of quartz/phenolic 5 harness satin. Validation between results of this study and results of precedent experiment is carried out, and the results have good agreement. Orthogonal conductivity of quartz/phenolic 5 harness satin is obtained and the effect of volume fraction of fiber is studied.
초음속 유동장내 2차분사 분사각도 변화에 따른 열전달 특성 변화
송지운(Jiwoon Song),이종주(Jong Ju Yi),조형희(Hyung Hee Cho),배주찬(Ju Chan Bae) 한국추진공학회 2008 한국추진공학회 학술대회논문집 Vol.2008 No.11
초음속 유동장내에 분사된 2차제트 주변에서의 열전달 현상을 고찰 하였다. 초음속 유동장내에 분사되는 2차유동의 Jet to freestream momentum ratio(운동량비)의 변화와, 2차유동 분사각도에 따른 2차 분사홀 주변의 열전달 특성을 파악하기 위하여 홀 주변의 표면온도 변화를 고속 적외선 카메라를 통하여 측정하였으며, 이를 이용하여 비정상 열유속 기법을 바탕으로 열유속을 계산하였다. 운동량비가 증가할 수록 열전달 현상이 강화 되었으며, 15˚ 기울어진 분사보다는 수직 분사의 경우에 더 강한 열전달 현상이 발생되었다. 이를 통해 분사비와 분사 각도가 표면 열전달 분포에 중요한 요인으로 작용함을 확인할 수 있었다. In this paper, heat transfer changes due to the shock/boundary layer interaction were investigated on surfaces where secondary jet are injected. With an infra-red thermography, surface temperature was measured and the measured data was used to obtain the convective heat transfer. Heat transfer is enhanced with increment of momentum ratio. And normal injection case has a higher heat transfer value than that of 15 degrees inclined injection case. Secondary injection momentum ratio and injection angle affect the surface heat transfer distribution.
운동량비와 냉각조건에 따른 이차분사 홀 주변의 열응력 해석
이남규(Namkyu Lee),송지운(Jiwoon Song),이종주(Jong Ju Lee),배지열(Ji-Yeol Bae),강윤구(Yoon Goo Kang),배주찬(Ju Chan Bae),조형희(Hyung Hee Cho) 한국추진공학회 2012 한국추진공학회 학술대회논문집 Vol.2012 No.11
본 연구는 평판의 이차 분사 체계에서 초음속 유동장의 상호 작용에 의해 발생하는 열응력을 수치적으로 연구했다. 해석은 상용코드인 ANSYS v.14를 이용하였다. 열경계조건으로는 선행 연구에서 운동량 비가 1.0, 1.5일 때 비정상 열유속 기법을 이용해 열전달 계수를 도출한 자료를 사용하였다. 평판의 재질은 초합금의 한 종류인 Inconel 718을 사용하였다. 실험 변수는 배면의 냉각조건으로써, 첫 번째는 냉매의 온도를 고정하고 열전달 계수를 200 ~ 500 W/m2·K 까지 변화시키고, 두 번째는 열전달 계수를 고정하고 냉매의 온도를 100 K~ 400 K 까지 변화시켰다. 결과는 열전달 계수가 300 W/m2·K 이상 증가하게 되면 평판의 상하면의 온도차이는 증가하지만 스트레스 변화의 폭이 줄어든다는 사실을 확인 할 수 있었다. This numerical study investigates thermal stress caused by supersonic flowfield interaction with secondary injection. The numerical investigation is conducted by ANSYS v.14. Heat transfer coefficient for this study uses past experimental data about momentum ratio 1.0 and 1.5. The flat plate is composed of Inconel 718 which is one of superalloy. Cooling condition is given by changing heat transfer coefficient or temperature of coolant.. Heat transfer coefficient is altered from 200 to 500W/m2·K in fixing condition of coolant, and temperature of coolant is varied from 100 to 400 K in fixing condition of heat transfer coefficient. The result is that thermal stress is steady above heat transfer coefficient around 300 W/m2 ·K though difference of temperature between upper and downward plate becomes larger.
수직 축대칭 과소팽창 충돌 제트의 표면 열전달 특성 연구
유만선(Man-Sun Yu),김병기(Byung-Gi Kim),조형희(Hyung-Hee Cho),황기영(Ki-Young Hwang),배주찬(Ju-Chan Bae) 한국항공우주학회 2005 韓國航空宇宙學會誌 Vol.33 No.8
축대칭 과소팽창 수직 충돌제트에 의한 표면 열전달 특성에 대하여 실험적 연구가 진행되었다. 초음속 유동장 내부의 충격파 구조 가시화와 함께 표면에서의 압력분포 및 열전달 계수가 측정되어졌다. 표면 열전달 계수는 노즐-충돌면간 거리와 과소 팽창비에 따라서 그 경향에 차이를 보였다. 이러한 현상은 벽압력 및 충격파 가시화에 대한 결과로부터 설명할 수 있었다. An experimental investigation has been carried out to examine heat-transfer characteristics of an axisymmetric, under-expanded, sonic jet impinging on a flat plate and the local measurement of surface pressures and heat transfer coefficients on a plate have been achieved together with a visualization test of shock structure in a jet. Heat transfer coefficients on a plate have been found to be changed significantly depending on the under-expansion ratio as much as the nozzle-to-plate distance. These phenomena could be explained by the wall pressure measurement and the shock visualization.