http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
박제진,이상하,박광원,하태준,Park, Je-Jin,Lee, Sang-Ha,Park, Kwang-Won,Ha, Tae-Jun 한국도로학회 2008 한국도로학회논문집 Vol.10 No.2
차량의 주행속도는 설계일관성을 평가하는 주요한 척도로 활용되며 그 중 곡선반경은 여러 연구에서 공통적으로 제시한 주된 요인으로 나타났다. 이에 본 연구에서는 복합선형에서 설계속도별 적정 평면곡선반경 범위기준을 정립하고 운전자의 인지 행태를 나타낼 수 있는 인지반경을 정립하여 입체선형에서 적합한 평면곡선반경을 제시하고자 한다. 첫째, 본 연구에서는 저속차량의 방해요소를 최소화하기 위하여 입체선형을 고려한 도로의 임의지점에서 횡방향 미끄럼 마찰계수와 주행방향 미끄럼 마찰계수를 동시에 고려하여 설계속도와 종단경사별 평면곡선반경을 제시하였다. 둘째, 본 연구에서는 곡선부 인지반경을 통하여 평면 곡선부와 편평한 종단경사가 조합된 경우, 평면 곡선부와 종단곡선부가 조합된 경우를 비교한 후, 곡선부 인지반경을 산정하여 설계속도별 적정 평면곡선반경과 인지반경 비율을 제시하였다. Achieving consistent geometric design is an important goal in highway design to ensure obtaining safe, economical and smooth traffic operation. Most evaluation of consistency is based on 'speed change' in speed profile. According to literature, the speed depends on geometric elements, speed on tangent section prior to a curve, and background around roads. Especially, the radius is the most main element mentioned in various literature. Therefore, this paper shows two ways of calculating horizontal radius on real road, that is, three-dimensional road. First of all, the radius of horizontal curve is calculated based on physical method. The calculated radius contains not only superelevation but also longitudinal grade while the current minimum radius is calculated by considering superelevation and side friction according to the point-mass equation. Secondly, the problem of composed curves with distorted appearance by overlaying sag or crest vertical alignment has been known. To quantify the extent of distortion effects, the method of calculation of real seen so called 'Perspective Radius' is developed. The paper presents the perspective radius and recommended perspective radius.
횡방향 가속도 모영을 이용한 곡선부 도로의 변이구간 평가에 관한 연구
박제진,김용길,고영선,하태준,Park, Je-Jin,Kim, Yong-Gil,Ko, Yeong-Sun,Ha, Tae-Jun 한국도로학회 2008 한국도로학회논문집 Vol.10 No.2
현행의 도로설계기준에서는 특정 설계속도에 따라 최소기준을 정하여 이를 토대로 설계된 도로가 해당 기준을 만족하면 주행상 안전성을 확보하는 것으로 간주하고, 이에 따라 도로설계 및 교통운영을 시행하고 있다. 그러나 실제 도로를 주행하는 차량의 속도를 조사해보면, 다수의 차량이 설계자의 의도와 다른 속도로 주행하는 것을 볼 수 있고, 이는 도로 이용자의 안전성 문제와 직결된다고 할 수 있다. 특히, 직선부에서 곡선부, 혹은 곡선부에서 직선부로 주행하는 곡선부 변이구간은 이러한 속도의 변동이 가장 심한 구간 중의 하나로 이에 대한 주행 안전성 검토가 절실하다. 따라서 본 연구에서는 첫째, 곡선부 도로 변이구간에서의 주행속도와 주행반경을 고려한 지점별 횡방향 가속도와 횡방향 가속도 변화율을 산정하고, 둘째, 이를 고려한 곡선부 도로 변이구간의 설계안전성을 평가하여 편경사, 곡선반경 등의 선형 설계요소를 검토하였다. 검토결과 현재 고려되어지고 있는 구심가속도는 실제 운전자가 부담해야 하는 구심가속도에 훨씬 못 미치고 있는 실정이며, 설계속도에 따라 구심가속도가 $25.56{\sim}77.78%$ 증가되어 주행안정성에 문제가 발생함을 확인할 수 있었다. 본 연구는 직선-단곡선으로 이어지는 곡선부 변이구간을 대상으로 하였다. According to the present highway design criteria, there are minimum standards which re ade from special design speeds. If some highways are satisfied the standards, it regards he highway as safety. In reality, however, most drivers drive a car at different speed compared with design speed. It is very dangerous for drivers especially at transition sections between curve and horizontal curve sections. Hence, this study calculated the rate of changing and horizontal acceleration at each section. Moreover, this study evaluated thesafety of design at curve transition sections and then calculated lateral acceleration and curve radii. This study found the minimum standards which are using as basic safety standards are not appropriate for measuring driver's safety.
박제진(Park, Je-Jin),김용석,하태준(Ha, Tae-Jun),이정환(Lee, Jeong-Hwan),박태훈(Park, Tae-Hun) 대한교통학회 2005 대한교통학회 학술대회지 Vol.49 No.-
시거는 안전한 도로의 설계와 운영을 위하여 필수적으로 고려하여야 할 설계기준의 하나이다. 시거의 종류에는 크게 정지시거, 앞지르기 시거, 판단시거, 교차로시거 등이 있다. 특히 정지시거는 운전자가 진행방향의 전방에 있는 장애물 또는 위험요소를 인지하고 제동을 걸어 정지할 수 있는 길이를 말하는데, 도로선형에 의해 운전자의 시야에 방해가 되지 않도록 도로 전구간에 걸쳐 정지시거가 확보되도록 설계하는 것은 매우 중요하며, 도로의 선형을 결정지우는 데 중요한 기준이 된다.