태양전지용CuInSe₂와 CuGaSe₂ 흡수층의 전자구조해석을 위한 표면 청정기술 개발

김경환,최형욱,공석현,Kim, Kyung-Hwan,Choi, Hyung-Wook,Kong, Sok-Hyun 한국전기전자재료학회 2005 전기전자재료학회논문지 Vol.18 No.2

Two kinds of physical treatments were examined for the analysis both of intrinsic surface and interior nature of CuInS $e_2$[CIS] and CuGaS $e_2$[CGS] films grown in separated systems. For the first method, a selenium protection layer which was immediately deposited after the growth of the CIS was investigated. The Se cap layer protects CISe surface from oxidation and contamination during the transport under ambient atmosphere. The Se cap was removed by thermal annealing at temperature above 15$0^{\circ}C$. After the decapping treatment at 2$25^{\circ}C$ for 60 min, ultraviolet photoemission and inverse photoemission measurements of the CIS film showed that its valence band maximum(VBM) and conduction band minimum (CBM) are located at 0.58 eV below and 0.52 eV above the Fermi level $E_{F}$, respectively. For the second treatment, an Ar ion beam etching was exploited. The etching with ion kinetic energy $E_{k}$ above 500 eV resulted in broadening of photoemission spectra of core signals and occasional development of metallic feature around $E_{F}$. These degradations were successfully suppressed by decreasing $E_{k}$ below 400 eV. CGS films etched with the beam of $E_{k}$ = 400 eV showed a band gap of 1.7 eV where $E_{F}$ was almost centered.st centered.

산화물기반 박막트랜지스터 전극용 ITO박막의 제작시 투입 산소 분압 의존성

김경환,Kim, Kyung Hwan 한국반도체디스플레이기술학회 2021 반도체디스플레이기술학회지 Vol.20 No.2

In this study, we investigated the oxygen partial pressure effect of ITO films for electrodes of oxide-based Thin-Film Transistor (TFT). Firstly, we deposited single ITO films on the glass substrate at room temperature. ITO films were prepared at the various partial pressures of oxygen gas 0-7.4% (O₂/(Ar+O₂)). As increasing oxygen on the process of film deposition, electrical properties were improved and optical transmittance increased in the visible light range (300-800 nm). For the electrode of TFT, we fabricated a TFT device (W/L=1000/200 ㎛) with ITO films as the source and drain electrode on the silicon wafer. Except for the TFT device combined with ITO film prepared at the oxygen partial pressure ratio of 7.4%, We confirmed that TFT devices with ITO films via FTS system operated as a driving device at threshold voltage (V_th) of 4V.

MEMS에 의한 On-chip 고종횡비 Air Core Solenoid 인덕터의 제작

김경환,Kim, Kyung-Hwan 한국전기전자재료학회 2006 전기전자재료학회논문지 Vol.19 No.8

We present high aspect ratio air-core solenoid inductors with $100{\mu}m\;and\;200{\mu}m$ tall via structures on Pyrex wafer. The effect of various parameters such as different number of turns, via heights, pitch distance between turns on inductor's radio frequency (RF) characteristics have been studied. The highest Q factor we obtained from various solenoid inductors is 72.8 at 9.7 GHz, which was produced by a 3-turn inductor.

CPM Bar Chart 기법을 활용한 일정계획

김경환,김수유,김재준,Kim Kyung-Hwan,Kim Soo-Yoo,Kim Jae-Jun 한국건설관리학회 2004 건설관리 : 한국건설관리학회 학회지 Vol.5 No.5

본 연구에서는 바차트(bar chart) 기법과 CPM 기법의 장점을 결합한 CPM bar chart(CBC) 기법을 제시한다. CBC는 기존의 fenced bar chart(FBC)의 장점을 유지하면서 단점을 보완한 것으로, 작업 관계를 나타내는 fence에 방향성을 부여함으로써, 기존 FBC에서 상당한 혼란을 유발하는 fence의 분리과정 없이 작업들의 관계를 표현할 수 있다. 또한, fence의 분리를 파악하기 위해 더미작업(dummy activity)을 확인하는 과정이 생략되어 보다 손쉽게 작성할 수 있는 장점도 있다. 바차트의 간결성을 유지하면서 CPM의 네트워크 논리 표현이 가능해짐에 따라, CBC는 다양한 프로젝트 참여자들 간의 원활한 의사소통에 기여하리라 예상된다. 또한, resource constrained scheduling, resource leveling, 작업 분리가 고려된 일정 조정, 공기 지연 분석 등의 CPM 기법에 기초한 다양한 일정 계획 및 관리에도 적용이 용이하여, 실무뿐만이 아니라 공정관리 교육과정에서도 활용성이 높으리라 기대된다. This paper proposes the CPM bar chart (CBC), a hybrid of the bar chart and the critical pad method (CPM). The CBC overcomes shortages of the fenced bar chart, while still keeping advantages. The fence with direction is applied instead of the broken fence, which triggers considerable problems to identify and apply in the fenced bar chart. In addition, the notorious task to find dummy activities is no longer required. Upon the benefits of simplicity in the bar chart and logical work sequence in the CPM network. the CBC provides a relatively easy way to create and understand a schedule, thus improving communication quality between project participants. With the advantages, the CBC can also be effectively applied to various scheduling techniques such as resource constrained scheduling, resource leveling, scheduling with activity split, delay impact analysis, etc.

슬관절 각도에 따른 교각운동이 하지근 활성도에 미치는 영향

김경환,기경일,윤혜진,Kim, Kyung-hwan,Ki, Kyong-il,Youn, Hye-jin 대한고유수용성신경근촉진법학회 2011 PNF and Movement Vol.9 No.1

Purpose : The purpose of this study was to assess the effects of the lower extremity muscle activity on bridging exercise according to the knee joint angle. Methods : Twenty-five healthy adults volunteered to participate in this study. Subjects were required to complete following four bridging exercises; knee joint flexion $120^{\circ}$, $90^{\circ}$, $60^{\circ}$, $45^{\circ}$. Surface electromyography from selected lower extremity muscles was normalized to maximum voluntary isometric contraction. Muscle activity was measured by QEMG-4 system (LXM 3204, Laxtha Korea). A repeated measures of one-way ANOVA was used to determine the influence of bridging exercise on muscle activity for each muscle and descriptive statistics was used to determine muscle ratio. Results : The biceps femoris of all bridging exercises showed significantly(p<.05). The vastus medialis and lateralis of all bridging exercises showed significant excepted $120^{\circ}$(p<.05). The rectus femoris of all bridging exercises showed no significant. Median of vastus medialis/rectus femoris ratio of $120^{\circ}$ was 2.03, $90^{\circ}$ was 2.16, $60^{\circ}$ was 2.67, $45^{\circ}$ was 4.10. Median of vastus lateralis/rectus femoris ratio of $120^{\circ}$ was 1.70, $90^{\circ}$ was 1.70, $60^{\circ}$ was 2.08, $45^{\circ}$ was 2.58. Median of vastus medialis/vastus lateralis ratio of $120^{\circ}$ was 1.26, $90^{\circ}$ was 1.50, $60^{\circ}$ was 1.52, $45^{\circ}$ was 1.47. Conclusion : Angular motion decreasing with knee joint flexion made increase biceps femoris and vastus medialis activation. This result will be use knee joint stabilizing exercises during bridging or unstable surface training and biceps femoris strength training.

개선된 자원 평준화 기법을 활용한 적정 공기산정 방안

김경환,윤영상,김재준,Kim Kyung-Hwan,Yoon Yung-Sang,Kim Jae-Jun 한국건설관리학회 2004 건설관리 : 한국건설관리학회 학회지 Vol.5 No.5

건설프로젝트는 일정한 기간 동안 주어진 목표를 수행하기 위한 작업들의 모임이라 정의할 수 있으며, 이를 위해서는 필요한 자원의 효율적 계획 및 관리가 필요하고, 이때 자원배당 및 자원평준화 기법이 활용된다. 하지만 자원제약이 있는 자원배당과 공기 제한이 있는 자원평준화 방법은 하나의 프로젝트에 개별적으로 적용되고 있어 전체 프로젝트의 공기와 효율적 자원이용 측면에서 적정화하기는 어렵다. 따라서 본 연구는 자원 평준화 방법의 Minimum Moment Algorithm 개념을 확대$\cdot$적용하여 적정 자원이용 및 공사기간을 산출하고자 한다. 이때 자원 활용의 상태를 나타내는 5가지 지표가 사용되며, 이들간의 중요도를 파악하기 위해 공정전문가를 대상으로 설문조사를 실시하였다. 마지막으로 가상 프로젝트의 적용을 통해 본 모형의 적용 가능성을 검증하고자 하였다. Since a construction project is a series of works that utilizes resources to accomplish the project goal for a given time period, efficient resource management is a prerequisite for the success of the project. Two major areas of resource management are resource constrained scheduling focusing on the limited resource availability and resource leveling focusing on smoothing resource usage pattern on the fixed project completion time. It is not available, however, to apply both techniques to a project at the same time. This paper proposes a model to enhance the minimum moment algorithm of resource leveling, aiming to find an efficient usage of resources and an appropriate project completion time. A survey was performed to evaluate the major five factors in the model. A case study demonstrates the value of the proposed resource leveling technique.

수직자기기록용 박막의 제작

김경환,김명호,손인환,김재환 ( Kyung Hwan Kim,Myung Ho Kim,In Hwan Son,Jae Hwan Kim ) 한국전기전자재료학회 1997 한국전기전자재료학회 추계학술대회논문집 Vol.1997 No.1

안드로이드 플랫폼 상에서 동기화가 고려된 통합 커서의 설계 및 구현

김경환,하주호,원종필,이의성,김주민,손진호,Kim, Kyung-Hwan,Ha, Jo-Ho,Won, Jong-Pil,Lee, Uee-Song,Kim, Joo-Min,Son, Jin-Ho 대한임베디드공학회 2011 대한임베디드공학회논문지 Vol.6 No.3

Android platform provides a content provider and a cursor mechanism to access the internal SQLite engine. Content providers not only store and retrieve data but also make it accessible to applications. Applications can only share data through content provider, since there's no common storage area that Android packages can access. Cursor is an interface that provides random read-write access to the result set returned by a database query. However, this cursor possesses two major limitations. First, a cursor does not support a join clause among cursors, since the cursor can only access a single table in the content provider. Second, the cursor is not capable of creating user-customized field in the predefined content providers. In this paper, we propose the unified cursor architecture that merges several cursors into a single virtual cursor. Cursor translation look-aside buffer (TLB), column windowing mechanism and virtual data management are the three major techniques we have adopted to implement our structure. And we also propose a delayed synchronization method between an application and a proposed unified cursor. An application can create a user-customized field and sort multiple tables using a unified cursor on Android platform.

고양지역 두 병원에서의 약물 중독 양상

김경환,박준석,신동운,노준영,김혜진,구홍두,조진경,김아진,Kim Kyung-Hwan,Park Jun-Soek,Shin Dong-Wun,Rho Jun-Young,Kim Hey-Jin,Gu Hong-Du,Cho Jin-Kyung,Kim Ah-Jin 대한임상독성학회 2006 대한임상독성학회지 Vol.4 No.1

Purpose: In the year of 2005, it enforced the basic study for establishing program of Poison Control Center by National Institute of Toxicologic Research. The object of our survey is to analyze the characteristics of intoxication from the City of Goyang by same protocol. Methods: We retrospectively reviewed the data of medical records of the intoxication patient in the two hospitals of the Goyang from 2004 June 1st to 2005 May 31th. The investigation protocol applied the TESS report form which was used from the Basic study for establishing program of Poison Control Center. Results: The intoxication patients were total 269 persons, the patients of A hospital were 184 persons, B hospital were 185 persons. The most common intoxication materials were medicines, in afterwords it was an agricultural chemical. The most common place of intoxication was the home. The intentional suicidal attempts in the reason of intoxication were 51.2%. The rate of the patients who discharges from the emergency department was 50.4% and death rate was 4.3%. Conclusion: We concluded that the continuous and systemic report and analysis should be accomplished from the Goyang area.

알루미늄 엣칭부산물을 첨가한 CPE 고무재료의 난연성 및 내열성 연구

김경환,이창섭,Kim, Kyung Hwan,Lee, Chang Seop 대한화학회 2001 대한화학회지 Vol.45 No.4

자동차 Oil cooler용 호스를 구성하는 클로로폴리에틸렌(CPE) 고무재료의 내열 및 난연성을 향상시키기 위하여 수산화알루미늄을 내열 및 난연제로 제조한 배합고무의 가황틀성, 물리적 성질, 내열성, 난연성을 조사하였으며, 실험결과로부터 고무와 난연제의 최적배합조건을 도출하였다. 고무시편을 제조하는데 사용된 고무재료는 화학적 내식성과 내한성이 우수하면서도 가격이 저렴한 클로로폴리에틸렌 고무를 사용하였으며, 내열 및 난연제로서는 알루미늄 표면 처리과정에서 발생되는 에칭부산물을 분쇄와 정제를 거쳐 가공한 수산화알루미늄을 사용하였고, 분말은 XRD(X-ray diffraction), PSA(Particle Size Analysis), SEM(Scanning Electron Microscopy) 및 ICP-AES(Inductively Coupled Plasma-Atomic Emission Spectroscopy)로 입자의 상, 크기, 분포, 형태 및 성분을 분석한 후 CPE 고무재료와 0∼80 phr범위에서 훈련하였다. CPE배합 고무의 경도, 인장강도, 신장율, 인장응력 및 열적특성을 분석한 결과, 고무재료규격을 초과하지 않는 범위 내에서 최대의 내열 및 난연효과를 주는 수산화알루미늄의 첨가량은 40 phr로 나타났으며, 이 배합비에서 클로로폴리에틸렌의 난연성은 3배 향상되었다. Aluminum Hydroxide was employed as a thermal retardent and flame retardent for Chloropolyethylene (CPE) rubbery materials which is the construction material of automotive oil cooler hose. and then cure characteristics, physical properties, thermal resistance and flame retardation of compounded rubber were investigated, and optimum mixing conditions of rubber and flame retarding agent were deduced from the experimental results. CPE rubber material which has excellent properties of chemical corrosion resistance and cold resistance and inexpensive in price was used to prepare rubber specimen. The by-product of ething, produced from the process of surface treatment of aluminum was processed to aluminum hydroxide via crushing and purification, which is characterized by XRD, PSA, SEM and ICP-AES techniques in terms of phase, size, distribution, morphology and components of particles and then mixed to CPE rubber materials in the range of 0~80 phr. Hardness, tensile strength, elongation and thermal properties of compounded rubber specimens were tested. The optimum mixing ratio of rubber to additives to give maximum effect on thermal resistance and flame retardation, within the range of tolerable specification for rubber materials, was determined to be 40 phr. The flame retardation of CPE rubber materials was found to be increased by 5 times at this mixing ratio.