http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
정의준(Chung Wui Jun),오상한(Oh Sang han) 대한기계학회 2008 대한기계학회 춘추학술대회 Vol.2008 No.5
The program using C/C?? which could calculate 3-D velocities from datas of the flowfield obtained by a slant hot-wire which has been developed. The characteristic of the exit flowfield of a circular nozzle with a curved surface was investigated. From the result, the inward-flow was verified at adjacent layers near the boundary of the exit flowfield of a circular nozzle in l d and outward-flow were sensed gradually from down flow of 1-d. Similarity of the nondimensional velocity profile properlly could be obtained except near 1-d and the virtual origion reasonablly could be obtained.
조인준 ( In Jun Cho ),오상한 ( Sang Han Oh ),이상욱 ( Sang Wook Lee ),손창호 ( Chang Ho Son ),정의준 ( Wui Jun Chung ) 한국물환경학회 2011 한국물환경학회지 Vol.27 No.2
In results of accomplishing fundamental study to improve the flocculant-mixing of the Flash-Mixer in Onsan Water-Treatment Plant at the small cost, We obtained 8.9% of mixing-efficiency from the field data and 3.2% of the characteristic flow-ratio as the available maximum volume-ratio in this Water-Treatment Plant. The optimum elements with the deflector diameter of 400 mm and deflector angle of 145° at the flow ratio of 3.2% could be obtained from the expanded study on the ground of the fundamental study. Finally, the efficiency could be improved about 510% from 8.9% to 45.4% and the average turbidity could be improved about 14%.
정의준 울산대학교 1998 공학연구논문집 Vol.29 No.1
축규압축기 회전익의 후방유동장을 45? 단일경사열선을 이용하여 측정하였고 특히 회전익 후방유동중 허브부근의 후류특성을 절현비에 따라 제시하였다. 유종장은 회전익으로부터 회전에너지를 받기 때문에 회전익이 회전하는 방향으로 회전하며 스팬(span)의 중간위치에서 후류의 중심들은 이현방향과 거의 일치한다. 또한 허브부근에서 후류의 중심들은 절현비가 큰 경우 회전하는 방향으로 편향되어 나타나고 있으나 잘현비가 작은류의 중심들은 절현비가 작은 경우에는 회전익의 회전방향과 반대방향으로 편향되어 나타나는데 이는 후류의 경계와 결합된와류 때문인 것으로 보여진다. 이러한 사실은 절현비가 큰 경우 말발굽와류, 코너와규 그리고 후류가 뚜렷이 구별되어 나타나고 있으나 절현비가 작은 경우 이러한 와류들과 후류는 서로 결합되어 새로운 와류를 형성하는 것으로부터 알 수 있다. 이러한 효과는 스팬의 ?? 이 상에서 사라진다. Measurement was made of the flow behind the rotor of a compressor by using a 45-degree-slanted hot wire. The characteristics of the wakd near the hub flow behind the rotor are investigated by the change of the pitch-chord ratio. The flow field rotors in rotational direction bacause of the field accepting the energy from a roter. The trace fo the wake center in the mid-span region almost lies on an extended line in the chord-wise direction, irrespective of pitch-chord rations. In the hub region, the wake center is shifted toward the rotational direction in the case of large pitch-chord ratio but it is shifted toward the anti-rotational firection in the case of small one because of the vortex mising with the boundaries of the wake. Also Near the hub region the house shoe vortex, the corner vortex and the wake appear clearly in the large pitch-chord ratio, but in the small pitch chord ratio these vortices and the wake are combined and form a new vortex. This effect disappers in the upper region from the ??.
평판의 Perforation에ㅐ 의한 유동저항 및 전열특성
정의준 울산대학교 1985 연구논문집 Vol.16 No.1
구멍이 있는 평판 전열면에 구멍의 크기 및 배열 방식이 마찰손실의 증가에 대하여 전열특성의 증가에 미치는 상대적 영향을 실험적으로 규명하였다. 실험결과는 구멍의 크기가 적고, 구멍간의 간격을 감소 시켰을 때 열전달 성능은 압력손실의 증가에 비하여 크게 향상되었다. The experimental study is carried out to investigate the relative increase of heat transfer performance in contrast to friction loss along the perforation diameter of plates or their arrangements. The Data of results indicate that when perforation diameter is small and its pitch is short the perforation of plates increase heat transfer performance without a large friction loss penalty.
정의준,김무현,김수태 울산대학교 1992 공학연구논문집 Vol.23 No.2
퍼스널 컴퓨터 및 스텝핑 모터를 사용한 자동계측장치를 개발하였고 이러한 자동계측장치를 이용하여 단일경사열선으로 유동장의 3차원 속도성분을 측정하였다. 검정실험을 통해 얻어진 검정실험식의 사용범위를 알아보기 위해 검정실험식의 사용범위를 알아보기 위해 검정실험식으로부터 구한 속도, 스윌각 및 피치각들을 실제 측정값들과 비교 검토하였다. The 3-D velocity components were measured by single slanted hot wire. An automatic measuring system which was controlled by means of a personal computer and stepping motors was developed. Absolute velocity, swirl angle and pitch angle are calculated from the outputs of hot wire anemometer using the calibration equations. The difference between the measured and calculated values was investigated.
정의준 울산대학교 1999 공학연구논문집 Vol.30 No.1
단일경사열선의 검정곡선들에 따르는 정확성을 파악하개 위해 수정된 Okiish 방법을 이용한 검정식의 검정곡선과 Inoue 방법의 검정식을 이용한 검정곡선이 이 검정곡선들을 얻는데 사용한 실험 데이터들과 비교되였다. 그 결과 단일경사열선의 물리적 특성에 좀 더 근접된 모델을 사용한 수정 Okiish 방법의 검정곡선이 Inoue 방법의 검정곡선 보다 오차가 적다는 것이 판명되었다. The accuracy of the calibration curve for the slanted hot wire is defined by the difference between the data making the calibration curve and the curve itself. And the error about the accuracy from the result of the difference is obtained. In comparision the accuracies of the calibration curves modified Okiish method is better than Inoue method from the results of the differences. This may be due to the fact that the model of modified Okiish method may reflect well the closer physical characteristics about the calibration curves for the slanted hot wire than that of Inoue method.