http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
김현구(Kim, Hyun-Goo),김효태(Kim, Hyo-Tae) 한국신재생에너지학회 2006 한국신재생에너지학회 학술대회논문집 Vol.2006 No.11
This paper introduces a radio-wave interference assessment of wind turbines that were planned to be installed at Homi-Cape in Pohang region where wind resource has been evaluated worthwhile developing a wind farm. In that area, AM radio station with two antennas and a harbor radar facility are located so that radio-wave coupling is inevitable if the wind farm is designed without considering radio-wave environmental impact. A low-frequency analysis using MoM (Method of Moment) is used to examine interference effect caused by wind turbines and an optimal layout minimizes coupling effect is presented.
CaZr(BO<sub>3</sub>)<sub>2</sub> 세라믹스의 마이크로웨이브 유전특성
남명화,김효태,김종희,남산,Nam, Myung-Hwa,Kim, Hyo-Tae,Kim, Jong-Hee,Nahm, Sahn 한국세라믹학회 2007 한국세라믹학회지 Vol.44 No.5
The microstructure and microwave dielectric properties of dolomite type borates, $CaZr(BO_3)_2$ ceramics prepared by conventional mixed oxide method were explored. The sintering temperature of $CaZr(BO_3)_2$ ceramics could be reduced from $1150^{\circ}C\;to\;925^{\circ}C$ with little amount of sintering additives. Microwave dielectric properties of 3 wt% $Bi_2O_3-CuO$ added $CaZr(BO_3)_2$ ceramics sintered at $925^{\circ}C$ were $K{\approx}10.4,\;Q{\times}f{\approx}80,000GHz\;and\;TCF{\approx}+2ppm/^{\circ}C$. Thus obtained LTCC tape was co-fired with Ag paste for compatibility test and revealed no sign of Ag reaction with the ceramics. Therefore, $CaZr(BO_3)_2$ ceramics is considered as a possible candidate material for low temperature co-fired multilayer devices.
BaSn(BO<sub>3</sub>)<sub>2</sub>세라믹스의 저온소결 및 유전특성
남명화,김효태,황준철,남중희,여동훈,김종희,남산,Nam, Myung-Hwa,Kim, Hyo-Tae,Hwang, June-Cheol,Nam, Joong-Hee,Yeo, Dong-Hoon,Kim, Jong-Hee,Nahm, Sahn 한국세라믹학회 2006 한국세라믹학회지 Vol.43 No.2
Dolomite type $BaSn(BO_3)_2$ ceramics with rhombohedral crystal structure has been synthesized via solid state reaction route. Dielectric properties were measured for the samples sintered at $1050\~1200^{\circ}C$ for 2 h in air. Dielectric constant, loss tangent, and temperature coefficient were increased with sintering temperature due to the evolution of $BaSnO_3$, secondary, phase. Optimum dielectric properties were obtained at the $BaSn(BO_3)_2$ ceramics sintered at $1100^{\circ}C.\;CuO/Bi_2O_3$ was added to $BaSn(BO_3)_2$ ceramics to lower the sintering temperature for LTCC application, then Co and Fe-based coloring agents were added for colorizing the LTCC tape. Typical dielectric properties of $BaSn(BO_3)_2$ ceramics with $5 wt\%\;CuO/Bi_2O_3\;and\;3wt\%$ Co-coloring agent that sintered at $900^{\circ}C$ were $\varepsilon_r=9.89,\;tan{\delta}=0.92\times10^{-3},\;and\;TCC=112ppm/^{\circ}C$. Thus obtained LTCC tape was co-fired with Ag paste for compatibility test and revealed no sign of Ag reaction with the ceramics.
이영규,김효태,남중희,김종희,백운규,Lee, Young-Gyu,Kim, Hyo-Tae,Nam, Joong-Hee,Kim, Jong-hee,Paik, Ungyu 한국세라믹학회 2006 한국세라믹학회지 Vol.43 No.1
The microwave dielectric properties and low temperature sintering of $Ca[Ti_{1-x}(Ni_{1/3}Nb_{2/3})_x]O_3$ system were investigated at the sintering temperature $1,200\~1,350^{\circ}C$. The density and quality factors $(Q{\times}f)$ increased while dielectric constants slightly decreased with the decrease of Ti. The dielectric constant, quality factor, and temperature coefficient of resonance frequency $(\tau_f)$ were 64, 17,000 GHz, and $-9.1\;ppm/^{\circ}C$ respectively, when $CaTi_{1/2}(Ni_{1/3}Nb_{2/3})_{1/2}O_3$ ceramics were sintered at $1,300^{\circ}C$ for 4 h. $2Li_2O-B_2O_3$ was added to $CaTi_{1/2}(Ni_{1/3}Nb_{2/3})_{1/2}O_3$ to decrease the sintering temperature for LTCC application. The microwave dielectric properties of the samples sintered at $925^{\circ}C$ for 2 h with the addition of $6\;wt\%\;2Li_2O-B_2O_3$ were $\varepsilon_r=48.7,\;Q{\times}f=8,460\;GHz$, and $\tau_f=+5.6ppm/^{\circ}C$. Compatibility test of the composition with silver electrode shows no reaction with silver electrode, implying the feasibility as a high-K LTCC material.
세라믹-금속 기반 LED 어레이 패키지의 저온동시소성시 휨발생 억제 연구
허유진,김효태,Heo, Yu Jin,Kim, Hyo Tae 한국마이크로전자및패키징학회 2016 마이크로전자 및 패키징학회지 Vol.23 No.4
고출력 LED 조명용 패키지를 제조함에 있어서 발열은 LED의 광출력과 수명에 매우 중요한 영향을 주는 인자로 알려져 있다. 본 연구에서는 가로등용 고출력 LED 패키지를 개발함에 있어서 효과적인 방열을 하기 위하여 방열효과가 상대적으로 우수한 구조인 chip-on-a-heat sink 구조를 가지는 세라믹-메탈 기반의 패키지를 제조하였다. 열확산 기능을 하는 heat sink 기판소재는 알루미늄 합금을, LED 어레이 회로를 형성하는 절연막으로는 저온동시소성용 glass-ceramics을 사용하였다. 특히 열처리 시 가장 이슈가 되는 세라믹-금속 하이브리드 패키지 기판의 휨을 억제하기 위한 수단으로서, glass-ceramic 절연막을 부분 코팅함으로써 휨현상을 용이하게 줄일 수 있게 되었다. 또한, LED 패키지의 방열특성의 향상 즉 열저항도 기존의 MCPCB 패키지나 전면 코팅형 절연막 패키지에 비해 훨씬 낮아지는 효과를 얻었을 뿐 아니라, 세라믹 코팅소재의 절감효과도 볼 수 있게 되었다. Ceramic-metal based high power LED array package was developed via thick film LTCC technology using a glass-ceramic insulation layer and a silver conductor patterns directly printed on the aluminum heat sink substrate. The thermal resistance measurement using thermal transient tester revealed that ceramic-metal base LED package exhibited a superior heat dissipation property to compare with the previously known packaging method such as FR-4 based MCPCB. A prototype LED package sub-module with 50 watts power rating was fabricated using a ceramic-metal base chip-on-a board technology with minimized camber deformation during heat treatment by using partially covered glass-ceramic insulation layer design onto the aluminum heat spread substrate. This modified circuit design resulted in a camber-free packaging substrate and an enhanced heat transfer property compared with conventional MCPCB package. In addition, the partially covered design provided a material cost reduction compared with the fully covered one.