http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
하기만(K.M Ha),김윤식(Y.S Kim),이성근(S.G Lee),오진석(J.S Oh),이홍찬(H.C Lee),김창국(C.K Kim) 한국마린엔지니어링학회 2007 한국마린엔지니어링학회 학술대회 논문집 Vol.2007 No.-
Versa Module Eurocard bus (VME) system은 고도의 안정성과 신뢰성을 요구하는 제어분야에 널리 사용되고 있다. 포항가속기연구소에는 다양한 전원장치의 실시간 제어와 신호처리를 위해 VME system을 사용한다. 주프로세서는 모토롤라의 74xx 시리즈의 power pc를 사용하고 있으며 데이터버스는 최대 64-비트를 지원한다. 제어를 위해서는 IP모듈을 사용하였고 PS는 fiber 미디어를 통해 5 Mbps로 고속통신이 이루어진다. 본 논문에서는 포항가속기연구소의 다중전원장치용 고속제어시스템의 하드웨어의 구조와 제어소프트웨어에 대하여 기술한다.
하기만(K.M Ha),김윤식(Y.S Kim),이성근(S.G Lee),오진석(J.S Oh),이홍찬(H.C Lee) 한국마린엔지니어링학회 2006 한국마린엔지니어링학회 학술대회 논문집 Vol.2006 No.-
The 108 multiplexed Beam Position Monitor (BPM) electronic modules and 2 digital BPM modules are installed to diagnose the beam position around Pohang Light Source (PLS) storage ring. To provide high quality beam to beam users, the stable orbit is maintained through the orbit feedback controlled correction Power Supply (PS) and steering PS after precise readout of the beam position. The multiplexed BPM analog output signal is scaled about the order of Volt/mm. To maintain the sub-micron orbit, a few hundred measurements should be done through analog and digital filter. In this paper, PLS Control/Measurement system are introduced for beam operation to measure sub-micron beam position and the new beam position monitoring hardware with the high resolution (>18-bit) is presented by using of analog/digital filter. Also the measurement data of the advanced Digital BPM is presented.
김윤식(Y.S Kim),하기만(K.M Ha),이성근(S.G Lee),오진석(J.S Oh),이홍찬(H.C Lee) 한국마린엔지니어링학회 2006 한국마린엔지니어링학회 학술대회 논문집 Vol.2006 No.-
Digital power supply controller using the Digital Signal Processor (DSP) and Field Programmable Gate Array (FPGA) has been developed over the years. Recently, full digital power supply controller has been studied and tested. A new digital controller is designed under 3U euro-standard size and provides quiet better overall performance characteristics than the standards of ± 5 ppm short-term stability (< 1 min) and ± 25 ppm long-term stability (< 12 hours). The digital controller adopted digital PID current control algorithm with single pole digital filter and feed-forward voltage ripple compensation loop. By implementation of the digital controller, it has the ability of high step resolution (150 ps) Digital Pulse Width Modulation (DPWM) for FET or IGBT switch drivers and high resolution (18-bit, 400 kSPS/2 MSPS) analogue to digital conversion for current and voltage signal measurement. In this paper, the hardware and software structures of the developed digital controller and experimental results of digital power supply are described.
Conceptual Design of PLS-II Control System for PLS
J.C. Yoon(윤종철),J.W. Lee(이진원),E.H. Lee(이은희),H.G Ha(하기만),J.M. Kim(김재명),S.J. Park(박성주),K.R. Kim(김경렬) 대한전기학회 2009 대한전기학회 학술대회 논문집 Vol.2009 No.7
PLS(Pohang Light Source) will begin the PLS-Ⅱ project that has been funded by the KOREA Government in order to further upgrade the PLS which has operated since 1992. The control system of the PLS-II has distributed control architecture, with two layers of hierarchy; operator interface computer (OIC) layer and machine interface computer (MIC) layer. The OIC layer is based on SUN workstation with UNIX. A number of PC-based consoles allow to remotely operating the machine from the control room. PC-based consoles use the Linux or Windows operation system. Similar consoles in the experimental hall are used to control experiments. The MIC layer is directly interfaced to individual machine devices for low-level data acquisition and control. MIC layer is based on VMEbus standard with vxWorks real-time operating system. Executable application software modules are downloaded from host computers at the system start-up time. The MIC's and host computers are linked through Ethernet network. It should enable the use of hardware and software already developed for specific light source requirements. The core of the EPICS (Experimental Physics and Industrial Control System)[1] has been chosen as the basis for the control system software.
ISO 9712에 따른 비파괴검사 기술자 자격인정 및 인증제도 수립을 위한 조사연구(Ⅰ)
이종포,박은수,한치현,하기수,장영권 한국비파괴검사학회 2003 학술대회 논문집 Vol.- No.1
비파괴검사 기술자에 대한 자격인정 및 인증에 관한 국제 표준인 ISO 9712가 1991년 제정되고 이후 개정판이 계속 이어지고 있다. 세계 각국은 자국의 비파괴검사 기술자 자격인정 및 인증제도를 국제 기준인 ISO 9712에 부합되게 고치거나 아직 자국에 그런 규정이나 제도가 없었던 나라들에서는 국제 기준에 맞는 제도를 수립해가고 있다. 우리나라는 국제 기준이 제정되기 이전에 국가기술자격법에 의한 비파괴검사 자격제도를 수립하였고 이후 국제 환경의 변화와 국제기준의 제정에 따라 자격기본법을 추가로 제정하여 시행하고 있으나 ISO 9712와는 거리가 멀어 비파괴검사 기술자 자격은 국가간에 상호 인정이 어렵도록 되어 있다. 한국 비파괴검사학회 표준화 위원회에서는 이와 같은 현실을 감안하여 ISO 9712에 따른 자격인정 및 인증 제도 수립을 위하여 ISO 9712와 관련된 국제 기준과 각국의 기준을 조사 분석하고, 국내의 관련 규정과 비교 검토함으로써, 국내에 새로운 자격제도 수립이나 자격제도 변경의 타당성을 조사 분석하였다. 본 원고에서는 1차년도의 조사 분석 연구결과를 여기에 요약 제시한다.