http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
태양전지용 CdS 박막의 제조 조건에 따른 전기적 광학적 특성에 관한 연구
이재형,Lee, Jae-Hyeong 한국전기전자재료학회 2008 전기전자재료학회논문지 Vol.21 No.7
Cadmium sulphide (CdS) thin film, which is used as a window layer of heterojunction solar cell, on the glass substrate was deposited by vacuum evaporation. Effects of deposition conditions such as the source and substrate temperature on electrical and optical properties of CdS films was investigated. As the source temperature was increased, the deposition rate of CdS films was increased. In addition, the optical transmittance and the electrical resistivity of CdS films were decreased as the source temperature was increased. This results were attributed to the increase of excess Cd amount in the film. The crystal structure of CdS films exhibited the hexagonal phase with preferential orientation of the (002) plane. As the substrate temperature was increased, the crystal structure of CdS films was improved and the resistivity of the films was increased due to the decrease of excess Cd in film.
태양전지 응용을 위한 고품위 및 저가격 ZnO 박막 제조에 관한 연구
이재형,Lee, Jae-Hyeong 한국정보통신학회 2010 한국정보통신학회논문지 Vol.14 No.1
본 연구에서는 타겟 제작에 드는 비용을 줄이고, 타겟 이용의 효율성을 높이기 위해 기존의 소결된 세라믹 타겟 대신 분말 타겟으로 사용하여 알루미늄 도핑된 산화아연(Aluminum doped zinc oxde; AZO)박막을 마그네트론 스퍼터법에 의해 제조하고, 스퍼터 압력에 따른 박막 물성을 조사하였다. 유리 기판에 증착된 AZO 박막은 타깃 종류 및 스퍼터 압력에 관계없이 기판에 수직한 c-축 방향으로 우선 성장방위를 갖는 hexagonal 구조로 성장되었다. 스퍼터 압력이 증가함에 따라 이 면 방향으로의 결정성장이 촉진되었다. AZO 박막의 전기적, 광학적 특성은 스퍼터 압력 증가에 따라 향상되었으며, 15 mTorr에서 $6.5{\times}10^{-1}\;{\Omega}-cm$의 최소의 비저항 값을 나타내었다. Aluminum doped zinc oxide (AZO) films have been prepared on Coming 7059 glass substrates by r.f. magnetron sputtering method. A powder target instead of a conventional sintered ceramic target was used in order to improve the utilization efficiency of the target and reduce the cost of the film deposition process. The influence of sputter pressure on the structural, electrical, and optical properties of AZO films were studied. The AZO films had hexagonal wurtzite structure with a preferred c-axis orientation, regardless of sputter pressure and target types. The crystallinity and degree of orientation was increased by increasing the sputter pressure. For higher sputtering pressures, a reduction of the resistivity was observed due to a increase on the mobility and the carrier concentration. The lowest resistivity of $6.5{\times}10^{-3}\;{\Omega}-cm$ and the average transmittance of 80% can be obtained for films deposited at 15 mTorr.
태양전지용 CdS 박막의 구조적 및 광학적 특성에 미치는 반응용액의 pH 영향
이재형,Lee, Jae-Hyeong 한국전기전자재료학회 2011 전기전자재료학회논문지 Vol.24 No.8
In this paper, CdS thin films, which were widely used window layer of the CdTe and the Cu(In,Ga)$Se_2$ thin film solar cell, were grown by chemical bath deposition, and effects of pH of reaction solution on the structural and optical properties were investigated. For pH<10.5, as the pH of reaction solution was higher, the deposition rate of CdS films was increased by improving ion-by-ion reaction in the substrate surface and the crystallinity of the films was improved. However, when the pH was higher than 10.5, the deposition rate was decreased because of smaller $Cd^{2+}$ ion concentration in the reaction solution. Also, the crystallinity of the films were deteriorated. The CdS films deposited at lower pH showed poor optical transmittance due to adsorbed colloidal particles, while the transmittance was improved for higher pH.
분말 타겟을 이용하여 증착된 ITO 박막의 열처리 특성
이재형,Lee Jae-Hyeong 한국전기전자재료학회 2006 전기전자재료학회논문지 Vol.19 No.2
Indium tin oxide (ITO) films have been prepared by DC magnetron sputtering. In order to improve the utilization efficiency of the target and reduce the cost of the film deposition processes, the powder target was used instead of the conventional ceramic target. As-deposited films were annealed at temperatures between $200^{\circ}C$ and $500^{\circ}C$ for 30 min in air. Also, the film was annealed in various atmospheres such as air, $O_2,\;H_2,\;N_2$, and vacuum at $400^{\circ}C$C for 30 min. Effects of the heat treatment conditions on structural, electrical, and optical properties of ITO films were investigated. The annealing temperature of $400^{\circ}C$ and atmospheres of $H_2$ and $N_2$ seem to be the most suitable conditions for post processing.
태양전지용 CdS 박막의 구조적, 광학적 물성에 미치는 스퍼터 전력 효과
이재형,임동건,양계준,Lee, Jae-Hyeong,Lim, Dong-Gun,Yang, Kea-Joon 한국전기전자재료학회 2006 전기전자재료학회논문지 Vol.19 No.4
CdS films have been prepared on polycarbonate, polyethylene terephthalate, and Coming 7059 substrates by r.f magnetron sputtering technique at room temperature. A comparison of the properties of the films deposited on polymer and glass substrates was performed. In addition, the influence of the sputter power on the structural and optical properties of these films was evaluated. The XRD measurements revealed that CdS films were polycrystalline and retained the mixed structure of hexagonal wurtzite and cubic phase, regardless of substrate types. As the sputter power was increased from 75 to 150 Watt, the structure of CdS films was converted from the mixed of hexagonal and cubic phase to hexagonal phase. The morphology of CdS films is found to be continuous and dense. Also, the grain of CdS films is larger with increasing the sputter power. The average transmittance exceeded 80 % in the visible spectrum for all films and decreases slightly with the sputter power.