http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
InSAR 고도계의 높이 및 각도 추정에 대한 모의실험
백인찬(Inchan Paek),이상일(Sangil Lee),전주환(Joohwan Chun),이혁중(Hyukjung Lee),장종훈(Jong Hun Jang) 한국전자파학회 2014 한국전자파학회논문지 Vol.25 No.8
본 논문에선 Interferometric Synthetic Aperture Radar(InSAR) 고도계의 측정값인 거리와 도래각(Angle of Arrival: AOA)을 실제 수치 표고 자료(Degital Elevation Model: DEM)상에서 모의실험하여 얻었다. 이 때 거리 측정값을 얻기 위해서 필요한 원시 데이터 및 압축 데이터의 결과도 나타냈다. 도래각은 안테나 간의 위상 차이로부터 Deterministic Maximum Likelihood Estimator(DMLE)를 사용하여 구했다. 거리 빈(range bin)의 크기와 펄스 반복 주기(PRI: Pulse Repetition Interval)가 실제 수치 표고 자료의 셀 크기에 비해 작기 때문에 모의실험에 적합하지 않다. 따라서 본 논문에서는 선형 보간법을 이용하여 해상도가 높은 수치 표고 자료를 생성하여 모의실험하였다. 서론 부분에서 InSAR 고도계를 소개하였고, 고도와 각도를 구하는 방법에 대해서 설명하였으며, 모의실험 부분에서 위에 소개된 방법의 성능을 보였다. We present a simulation study of an algorithm for the range and angle of arrival(AOA) estimation with an interferometric synthetic aperture radar(InSAR) altimeter using a real digital elevation model(DEM). We also illustrate a step-by-step procedure of generating raw InSAR data, as well as their range and azimuth compressed data, which is to be used for the subsequent altitude and angle estimation. The AOA is estimated using a deterministic maximum likelihood estimator(DMLE) applied to the first arrived point for each pulse in the compressed data obtained with three antennas. The range bin size and the pulse repetition interval(PRI) are much smaller than the cell size of the DEM used in this study. To make the DEM compatible to the radar parameters, we first generate a higher resolution DEM by linearly interpolating the given DEM. After a brief description of the principle of the InSAR altimeter, the algorithms for altitude and angle estimation are presented, and their performance is assessed through simulation.
백인찬(Inchan Paek),이상일(Sangil Lee),유경주(Kyungju Yoo),장종훈(Jong Hun Jang) 한국전자파학회 2015 한국전자파학회논문지 Vol.26 No.1
본 논문에서는 지형기반항법 시스템에 적용을 위해 레이더 고도계로부터 최근점의 경사거리 고도와 비행횡축방향 각도를 측정할 수 있는 구조의 간섭계 레이더 고도계 성능을 사전 검증하기 위해 MATLAB을 사용하여 컴퓨터 GUI 기반의 시뮬레이터를 구현하였다. 서론 부분에서 지형기반항법과 간섭계 레이더 고도계에 대하여 간략하게 소개를 하였고, 단원 II에서는 수치지형자료(Digital Elevation Map: DEM)에서 반사 신호를 모델링하기 위한 기본단위 격자를 나누고, 각각의 격자마다 레이더 반사 단면적(Radar Cross Section: RCS)을 계산하여 빔폭 내의 반사 신호에 대한 신호대 잡음비(Signal-Noise Ratio: SNR)를 계산하는 과정을 설명하였다. 또한, 단원 III과 IV에서는 간섭계 레이더 고도계 신호처리 과정과 시뮬레이터의 구조를 설명하였다. We present an implementation result of a computer GUI-based simulator using MATLAB to verify the performance of interferometric radar altimeter(IRA) which is possible to measure the slant range altitude and the cross-track angle to the nearest point for terrain aided navigation(TAN). After a brief description of the principle of TAN and IRA, we present that the grids are divided for the modeling of the reflected signal in digital elevation map(DEM) and so the radar cross section(RCS) of each grid is calculated and the signal-noise ratio(SNR) of the reflected signal in the radar beam width. And the signal processing procedures of the IRA and the structure of the IRA simulator are shown.
임펄스 초광대역 레이다를 이용한 점표적의 ISAR 기하 보정 방법
유지웅(Jiwoong Yu),니키틴 콘스탄틴(Konstantin Nikitin),백인찬(Inchan Paek),장종훈(Jong Hun Jang),가민호(Min-Ho Ka) 한국전자파학회 2015 한국전자파학회논문지 Vol.26 No.4
본 논문은 임펄스 초광대역 레이다를 이용한 ISAR 영상의 기하보정 방법에 대해 서술하였다. 임펄스 초광대역 레이다는 시간영역에서 신호처리를 하므로 다중 경로, 간섭 문제 등이 일어나지 않는 장점이 있다. 안테나와 대상체 사이의 송수신 신호를 평면파라고 가정하면, ISAR 기하 모델에서 회전축의 중심을 점표적을 이용하여 계산한다. 수신 데이터에서 합성을 수행하기 전, 점표적은 최대 점의 위치를 최소 자승법으로 근사하여 회전축의 중심을 알아낼 수 있다. 이 방법은 대조비가 더 뛰어난 영상을 얻을 수 있었고, 엔트로피도 가장 큰 값을 가질 수 있었다. 이러한 방법은 장비를 최초 작동하거나 주기적으로 사용되어서 회전축의 중심을 보상하여 영상 합성을 할 것이다. 의료나 보안 감시와 같은 고정된 기하를 가지는 영상화 장비에서 유용하게 사용될 것이다. In this paper, a method of ISAR geometric calibration is represented by using impulse-radio UWB radar. The ir-UWB is good for using a signal processing in time domain, so, it does not occur a multi-path or coupling problem. If a signal that between antennas and target is assumed a plane wave, a center of rotation in ISAR geometry model can be estimated by using point target. Before image is reconstructed with sinogram, the center of rotation can be calculated by using least square fitting. This method can be obtained a more contrast image, and a maximum value of entropy of image. The method, that estimates a center of rotation in received data, will be used a initial setup of instruments or a periodic compensation to reconstruct image. It would be useful in medical, security and surveillance imaging equipments that have a fixed geometry.
백인찬,이건상,김민수,권영헌 漢陽大學校 自然科學硏究所 1997 自然科學論文集 Vol.16 No.-
지속적으로 발성한 우리말 모음 / 이 / 에 대해 화자의 특징을 나타내는 벡터 양자화 코드북을 만들고 이를 이용하여 화자인식 실험을 실행하였다. 먼저 각각의 피치주기를 구하여, 분석 프레임의 길이를 피치주기의 정수배로 변화시켜 실험하였다. 이때 피치주기와, 코드북의 대표벡터 개수의 변화에 따른 인식결과를 비교하였다. 인식실험에 사용한 특징벡터로는 10차의 선형예측계수를 이용하였다. A speaker identification scheme using the speaker-based VQ codebook of a sustained vowel is proposed and tested. First of all, the pitch period of each speech is obtained, and the frame length with a number times of the pitch period is used. The experimental results by variation of the VQ-level of codebook and the pitch period are studied. The 10-dimension LPC vector is used as a feature vector.