http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
윤희철(Hee Chul Youn),우창기(Chang Ki Woo),황재곤(Jai Kon Hwang) 대한기계학회 2015 大韓機械學會論文集A Vol.39 No.7
저압터빈 최종단 블레이드는 발전설비의 대용량화에 따라 대형화 되고 있으며, 터빈을 구성하는 모든 블레이드 중 상대적으로 그 크기가 가장 크다. 그 결과 블레이드는 매우 높은 원심력과 낮은 고유 진동수 특성을 가지며 그에 따른 각종 손상이 발생하게 된다. 최근 국내에서 가동연수 증가와 잦은 기동정지에 따른 저압터빈 최종단 블레이드의 손상이 자주 보고되고 있어, 본 연구에서는 유한요소법을 이용하여 원심력에 의한 응력해석, 응력경화효과에 따른 고유진동수 해석 및 조화응답해석을 수행 하였다. 그 결과 예측된 블레이드의 에어포일 선단부 최대 피로응력의 위치와 실제 균열의 발생위치가 일치함으로써 피로손상에 의한 결과임을 확인하였고, 노치에 의한 등가피로한도가 노치피로한도에 접근하였다. The sizes of the final blades of a low-pressure (LP) steam turbine have been getting larger for the development of high-capacity power plants. They are also larger than the other blades in the same system. As a result, fatigue damage is caused by a large centrifugal force and a low natural frequency of the blade. Recently, many failure cases have been reported due to repeated turbine startups and their prolonged use. In this study, the causes and mechanism of failure of a LP turbine blade were analyzed by using a finite element method to calculate the centrifugal force, the natural frequency of a stress-stiffening effect, and the harmonic response. It was observed that the expected fatigue damage position matched the real crack position at the airfoil’s leading edge, and an equivalence fatigue limit approached a notch fatigue limit.
주파수 응답해석을 통한 제작공차를 가지는 저압터빈 케이싱의 고진동 원인 규명
윤희철(Hee-Chul Youn),우창기(Chang-Ki Woo),황재곤(Jai-Kon Hwang) 한국생산제조학회 2015 한국생산제조학회지 Vol.24 No.4
High vibration of a low pressure (LP) turbine casing caused safety problems and life at the facility it was housed in. The main focus of this study was the cause of the high vibration in a low pressure turbine casing with manufacturing defects by frequency response analysis, compared with the results of experiments. Therefore, excited accelerations were obtained from the LP casing fundamental, and frequency responses were analyzed. The measurement and the modal analysis showed that the natural frequency of the LP turbine casing was 61.26 Hz and the excited frequency of the turbine rotor was 60.25 Hz. The manufacturing defect caused a decrease in the casing natural frequency and resulted in the high vibration of the casing because it moved close to the resonant frequency.
균열을 내재한 저압터빈 최종단 블레이드의 진동 특성 및 파괴 임계균열길이 해석
윤희철(Hee-Chul Youn),우창기(Chang-Ki Woo),이장규(Zhang-Kyu Rhee) 한국생산제조학회 2016 한국생산제조학회지 Vol.25 No.5
The sizes of last stage blades (LSB) in a low-pressure steam turbine have been getting larger for the development of high-capacity power plants. They are also larger than other blades in the same system. As a result, crack propagation in an LSB is caused by the large centrifugal force, low natural frequency, and repeated turbine startups. In this study, the critical crack length for a fracture and vibration characteristics, in accordance with crack propagation, were analyzed using a finite element method to calculate the stress intensity factor (SIF) and the natural frequency that was affected by the stress-stiffening effect. It was calculated that the frequency of the third and fifth modes passed the excited harmonic resonance (5X and 10X) and the observed calculated critical crack length matched that of the real fractured surface.
100 MW급 가스터빈 1단 블레이드의 피로파괴 발생 원인
윤희철(Hee-Chul Youn),우창기(Chang-Ki Woo) 한국생산제조학회 2015 한국생산제조학회지 Vol.24 No.6
Many failures have been reported in gas turbine facilities owing to repeated startups and prolonged use of the turbines. In this study, the causes and mechanism of fatigue failure in the first blade of a gas turbine were analyzed using a finite element method to calculate the centrifugal force, bending force, and a modal analysis based on the stress-stiffening effect and harmonic response under the operating conditions. The results show that, fatigue damage was caused by the resonance conditions encountered, in which the first natural frequency declined along with an increase in the metal temperature of the blade. The position of the expected fatigue damage was shown to match the actual position of the cracking at the root area of the blade, which was on the concave side. In addition, the quivalence fatigue stress was observed to approach the fatigue limit.