http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
상사 모델과 전산 수치 해석을 이용한 diffuser/nozzle pump의 정상 상태에 대한 연구
박성훈(Sung Hoon Park),고상근(Kauh S. Ken) 대한기계학회 2007 대한기계학회 춘추학술대회 Vol.2007 No.5
Recently, as the semiconductor production technology develops, there has been growing interest in the cooling system using micro fluid pump. Among the various types of micro fluid pump, the valve-less diffuser/nozzle has been extensively studied in recent years. However, the flat-walled diffuser/nozzle flow has not been clearly looked into due to its non-linear characteristics. In this paper, the flow characteristics of the flat-walled diffuser/nozzle have been analyzed using similitude model and simulations. Similitude models are designed so that the flow pattern is same as that of 1/10 scale flow by using high viscous fluid as working fluid. The results are compared to the simulations. It is shown that the flow characteristics of 2D simulation are different from 3D simulations at high Re region, and the measured pump efficiency is highly dependent on the pressure difference as well as the channel geometry. From these results, the desirable conditions for the efficient pump is discussed.
박성훈(Sung Hoon Park),고상근(Kauh. S. Ken) 대한기계학회 2007 대한기계학회 춘추학술대회 Vol.2007 No.10
Recently, as the semiconductor production technology develops, there has been growing interest in the cooling system using micro fluid pump. Among the various types of micro fluid pump, the valve-less diffuser/nozzle has been extensively studied in recent years. However, the flat-walled diffuser/nozzle flow has not been clearly looked into due to its non-linear characteristics. In this paper, the flow characteristics of the flat-walled diffuser/nozzle have been analyzed in the various channel geometries and pressure boundary conditions at the laminar flow region. From these results, the geometries and boundary conditions for the efficient pump operations are investigated, and modified variables are adjusted as the parameters of the pump efficiency. The experiments are conducted based on the similitude method, and the results are compared to the simulations. It shows that the desirable condition does exist for the efficient diffuser/nozzle pump operation.
A study of direct moxibustion using mathematical methods.
Liu, Miao,Kauh, Sang Ken,Lim, Sabina Gordon and Breach Science Publishers 2012 Computer methods in biomechanics and biomedical en Vol.15 No.4
<P>Direct moxibustion is an important and widely used treatment method in traditional medical science. The use of a mathematical method to analyse direct moxibustion treatment is necessary and helpful in exploring the new direct moxibustion instruments and their standardisation. Thus, this paper aims to use a mathematical method to study direct moxibustion in skin to demonstrate a direct relationship between direct moxibustion and skin stimuli. In this paper, the transient thermal response of skin layers is analysed to study direct moxibustion using the data got from standardised method to measure the temperature of a burning moxa cone. Numerical simulations based on an appropriate finite element model are developed to predict the heat transfer, thermal damage and thermal stress distribution of barley moxa cones and jujube moxa cones in the skin tissue. The results are verified by the ancient literatures of traditional Chinese medicine and clinical application, and showed that mathematical method can be a good interface between moxa cone and skin tissue providing the numerical value basis for moxibustion.</P>
A Bluetooth Scatternet Reformation Algorithm
Lee Han-Wook,Kauh Sang-Ken The Korea Institute of Information and Commucation 2006 Journal of communications and networks Vol.8 No.1
Bluetooth is reputed as a wireless networking technology supplying ad-hoc networks between digital devices. In particular, Bluetooth scatternet is an essential part of dynamic ad-hoc networks. Yet, there have not been sufficient researches performed on scatternet environment. This paper proposes a scatternet reformation algorithm for ad-hoc networks for instances where some nodes enter or leave the scatternet. The proposed algorithm is a general algorithm that can be applied to many types of Bluetooth scatternet regardless of the topology. The proposed algorithm is made for two reformation cases, i.e., nodes leaving and nodes entering. For the reformation when nodes leave a scatternet, the recovery node vector (RNV) algorithm is proposed. It has short reformation setup delay because the process involves a single page process (not including inquiry process). For the reformation when nodes enter a scatternet, the entry node algorithm is proposed. This is a simple and easily implementable algorithm. In this paper, real hardware experiments are carried out to evaluate the algorithm's performance where the reformation setup delay, the reformation setup probability and the data transfer rate are measured. The proposed algorithm has shown improvement in the reformation setup delay and probability.
구남희,고상근,하경표,Ku, Nam-Hee,Kauh, Sang-Ken,Ha, Kyoung-Pyo 대한기계학회 2003 大韓機械學會論文集B Vol.27 No.9
Pressure coefficient in a rotating discharge hole was measured to gain insight into the influence of rotation on the discharge characteristics of rotating discharge holes. Pressures inside the hole were measured by a telemetry system that had been developed by the authors. The telemetry system is characterized by the diversity of applicable sensor type. In the present study, the telemetry system was modified to measure static pressure using piezoresistive pressure sensors. The pressure sensor is affected by centrifugal force and change of orientation relative to the gravity. The orientation of sensor installation for minimum rotating effect and zero gravity effect was found out from the test. Pressure coefficients in a rotating discharge hole were measured in longitudinal direction as well as circumferential direction at various rotating speeds and three different pressure ratios. From the results, the behaviors of pressure coefficient that cannot be observed by a non-rotating setup were presented. It was also shown that the discharge characteristics of rotating discharge hole is much more influenced by the Rotation number irrespective of pressure ratio.
High-speed Three-dimensional Surface Profile Measurement with the HiLo Optical Imaging Technique
Kang, Sewon,Ryu, Inkeon,Kim, Daekeun,Kauh, Sang Ken Optical Society of Korea 2018 Current Optics and Photonics Vol.2 No.6
Various techniques to measure the three-dimensional (3D) surface profile of a 3D micro- or nanostructure have been proposed. However, it is difficult to apply such techniques directly to industrial uses because most of them are relatively slow, unreliable, and expensive. The HiLo optical imaging technique, which was recently introduced in the field of fluorescence imaging, is a promising wide-field imaging technique capable of high-speed imaging with a simple optical configuration. It has not been used in measuring a 3D surface profile although confocal microscopy originally developed for fluorescence imaging has been adapted to the field of 3D optical measurement for a long time. In this paper, to the best of our knowledge, the HiLo optical imaging technique for measuring a 3D surface profile is proposed for the first time. Its optical configuration and algorithm for a precisely detecting surface position are designed, optimized, and implemented. Optical performance for several 3D microscale structures is evaluated, and it is confirmed that the capability of measuring a 3D surface profile with HiLo optical imaging technique is comparable to that with confocal microscopy.
길이 대 직경 비와 입구 모서리 반경에 따른 회전 오리피스의 송출 특성
하경표,강세원,고상근,Ha, Kyoung-Pyo,Kang, Se-Won,Kauh, Sang-Ken 대한기계학회 2000 大韓機械學會論文集B Vol.24 No.7
The effect of rotation on the discharge coefficient of orifices with various length-to-diameter ratios and two different inlet corner radii was studied. Length-to-diameter ratios of the orifices range from 0.2 to 10, while the inlet shapes are square edged, or round edges of radius-to-diameter ratio of 0.5. From the experiment, we found that rotational discharge coefficient and Rotation number, when based on ideal exit velocity of the orifice considering momentum transfer from the rotor, describe the effect of rotation very well. In this study, the discharge coefficients of rotating orifices are shown to behave similar to those of the well-known non-rotating orifices. For both rotating and non-rotating orifices, the discharge coefficients increase with the length-to-diameter ratio until a maximum is reached. The flow reattachments in the relatively short orifices are responsible for the increase. The coefficient then decreases with the length-to-diameter ratio due to the friction loss along the orifice bore. The length-to-diameter ratio that yields maximum discharge coefficient, however, increases with the Rotation number because the increased flow-approaching angle requires larger length-to-diameter ratio for complete reattachment. The length-to-diameter ratio for complete reattachment is shorter for round edged orifices than that of square edged orifices by about a unit length-to-diameter ratio.