이중 기공구조를 갖는 다공질체의 제조

윤중열,김해두,박천홍,Yun, Jung-Yeul,Kim, Hai-Doo,Park, Chun-Hong 한국세라믹학회 2002 한국세라믹학회지 Vol.39 No.10

표면층과 내부간의 기공구조가 다른 다공질체를 제조하기 위해 입자크기가 다른 두 종류의 분체를 이용하여 다공질 성형체를 제조하였다. 두 층간의 소결 수축율을 동일하게 제어하기 위해 성형밀도 변화에 따른 소결밀도 변화를 예측할 수 있는 Ford's equation을 도입하여 소결 수축율을 동일한 조건을 구하였다. 제조된 다공질체는 미세구조와 통기도를 조사함으로서 기공의 이중 구조화 여부를 평가하였다. SEM 관찰결과 기공크기가 다른 두 층으로 구성되어 있는 것을 확인하였다. 각 층의 통기도는 출발 입자크기와 기공율이 클수록 증가하였으며, 이중 기공구조를 갖는 시편의 통기도는 기공크기가 작은 층의 특성에 의존하였다. In order to fabricate double-layered porous materials powders of different particle sizes were pressed stepwise. Ford's equation which predicts the fired density with the change in pressed density was employed in order to adjust the difference in sintering shrinkage of the green body with double-layered porous structure. Double-layered porous materials were characterized by investigating microstructures and permeability. SEM micrographs showed the distinct difference in pore sizes of double-layered porous material. Permeability of single-layered porous material increased by increasing the starting particle sizes and porosity as well. Permeability of the double-layered porous material depends largely on the layer of small pore diameter.

보론과 카본 조제를 사용한 AlN-SiC-TiB₂계의 고온가압 및 Spark Plasma Sintering

이세훈,김해두,Lee, Sea-Hoon,Kim, Hai-Doo 한국세라믹학회 2009 한국세라믹학회지 Vol.46 No.5

Effects of boron and carbon on the densification and thermal decomposition of an AlN-SiC-$TiB_2$ system were investigated. $SiO_2$ was mostly removed by the addition of carbon, while $Al_2O_3$ formed $Al_4O_4C$ and promoted the densification of the systems above $1850^{\circ}C$. Rather porous specimens were obtained without the additives after hot pressing at $2100^{\circ}C$, while densification was mostly completed at $2000^{\circ}C$ by using the additives. The sintering temperature decreased further to $1950^{\circ}C$ by applying spark plasma sintering. The additives promoted the shrinkage of AlN by forming a liquid phase which was originated from the carbo- and boro-thermal reduction of $Al_2O_3$ and AlN.

연소합성법에 의한 발열성 다공질 MoSi₂계 재료의 제조

송인혁,윤중열,김해두,Song, In-Hyuck,Yun, Jung-Yeul,Kim, Hai-Doo 한국세라믹학회 2004 한국세라믹학회지 Vol.41 No.1

본 연구에서는 SHS 공정에 의하여 기공의 크기를 조절함으로서 전기저항 발열 특성을 가지는 다공성 $MoSi_2$를 제조하는 공정에 관하여 연구하였다. 결함이 억제된 다공질 재료를 제조하기 위하여 Si 함량 변화 및 예열 공정을 실시하였으며, 성형체 제조에 사용되는 Mo 분말의 크기 변화에 따른 가공 형성 거동에 대하여 연구하였다. 실험 결과 합성된 $MoSi_2$ 입자의 크기는 Mo 입자의 크기와는 관계없이 연소 합성시 발열되는 발열양에 의해 좌우되었으며, 기공의 크기는 Mo 입자의 크기에 따라 결정되었다. 또한 가공 경사 $MoSi_2$ 다공질 재료를 만들기 위하여 150-300${\mu}m$ Mo 분말과 4-5${\mu}m$ Mo 분말을 단계별로 5층으로 혼합하여 합성한 결과 거시적으로 순차적인 기공 크기 분포를 나타내었으며, 이를 통하여 포집 효율등이 우수한 다공성 발열체 재료의 제조가 가능하였다. In this study, SHS process has been employed to fabricate porous $MoSi_2$ material with electric-resistive heating capability through the control of pore size. The preform for SHS reaction was consisted of molybdenum powder with different sizes and silicon powder with different contained quantity. The size of the $MoSi_2$ particles thus formed was determined by the generated heat of combustion, not by the size of molybdenum powder. However, the pore size of $MoSi_2$ composite was proportional to the particle size of molybdenum powder. that is the coarser the molybdenum powder used, the larget the formed pore size. Based on these results, the porous $MoSi_2$ composite could be fabricated with a desired pore size. By orienting the porous molybdenum disilicide-based material in the form of pore size gradient, porous materials used for filters with improved dirt-holding capacity can be manufactured.

Si 결합 다공성 탄화규소의 미세구조 및 통기도 특성 -카본 함량 변화 중심

송인혁,박미정,김해두,김영욱,배지수,Song, In-Hyuck,Park, Mi-Jung,Kim, Hai-Doo,Kim, Young-Wook,Bae, Ji-Soo 한국세라믹학회 2010 한국세라믹학회지 Vol.47 No.6

The achievement of high gas permeability is a key factor in the development of porous SiC ceramics for applications of hot gas filter, vacuum chuck, and air spindle. However, few reports on the gas permeability of porous SiC ceramics can be found in the literature. In this paper, porous SiC ceramics were fabricated at temperatures ranging from $1600^{\circ}C$ to $1800^{\circ}C$ using the mixing powders of SiC, silicon, carbon and boron as starting materials. In some samples, expanded hollow microspheres as a pore former were used to make a cellular pore structure. It was possible to produce Si bonded SiC ceramics with porosities ranging from 42% to 55%. The maximum bending strength was 58MPa for the carbon content of 0.2 wt% and sintering temperature of $1700^{\circ}C$. The increase of air permeability was accelerated by addition of hollow microsphere as a pore former.

반도체 폐 Si 슬러지를 이용한 질화규소세라믹의 제조

이병택,유정호,김해두,Lee, Byong-Taek,Yoo, Jung-Ho,Kim, Hai-Doo 한국재료학회 1999 한국재료학회지 Vol.9 No.12

반도체 폐 Si슬러지를 이용하여 질화반응 및 post-sintering을 통해 제조된 질화규소세라믹의 미세조직 및 기계적 특성을 광학현미경, SEM 및 XRD를 이용하여 연구하였다. 상당량의 $SiO_2$ 비정질상을 포함하는 폐 Si분말에서 많은 microcracks이 관찰되었다. 폐 슬러지를 사용한 Si 성형체의 질화율은 상용되고 있는 Si분말을 이용한 성형체의 값에 비해 낮은 값을 보였다. 그러나 질화온도가 증가함에 따라 질화율은 증가하였으며 1470$^{\circ}C$에서 질화율은 98%를 보였다. 반응소결체내에 존재하는 $Si_3N_4$의 결정은 ${\alpha}$와 ${\beta}$상으로 혼재되어 있으며 상당량의 산질화규소상이 검출되었다. 1950$^{\circ}C$에서 후처리된 시료의 최대파괴인성 및 파괴강도 값은 각각 5.6 $^MPa{\cdot}m^{1/2}$과 497 MPa로 H. C. Starck사의 Si을 이용한 것에 비해 낮은 값을 보였으며 이는 산질화규소 형성에 기인한 것으로 사료된다. The microstructures and mechanical properties of $Si_3N_4$ ceramics produced by nitridation and post-sintering using semiconductor-waste-Si sludge were investigated. Lots of microcracks were observed in the waste-Si powders which contained some amounts of amorphous $SiO_2$. The nitridation rate of waste-Si compacts showed lower value than that of commercial Si powder compacts. The nitridation rate was increased with increasing nitridation temperature and then the percent of nitridation at 1470$^{\circ}C$ showed 98%. The phases of $Si_3N_4$ in the reaction-bonded bodies were mixed with ${\alpha}$ and ${\beta}$-type, and small amounts of $Si_2N_2O$ phase while those after post-sintering were ${\beta}$-$Si_3N_4$ and ${\alpha}$-Sialon. The sample post-sintered at 1950$^{\circ}C$ showed the fracture toughness of 5.6 $^MPa{\cdot}m^{1/2}$ and the fracture strength of 497 MPa which were lower than those of sintered body using commercial Si powder possibly due to the formation of ${\alpha}$-Sialon phase.

중공형 미세구를 이용한 마이크로셀룰라 지르코니아의 가공 특성 고찰

이은정,송인혁,김해두,김영욱,배지수,Lee, Eun-Jung,Song, In-Hyuek,Kim, Hai-Doo,Kim, Young-Wook,Bae, Ji-Soo 한국세라믹학회 2009 한국세라믹학회지 Vol.46 No.1

In this study, a novel-processing route for producing microcellular zirconia ceramics has been developed. The proposed strategy for making the microcellular zirconia ceramics involves hollow microsphere as a pore former which has extremely low density of $0.025\;g/cm^3$. Effects of hollow microsphere content and sintering temperature on microstructure, porosity, pore distribution, and compressive strength were investigated in the processing of microcellular zirconia ceramics. By controlling the content of hollow microsphere, it was possible to make the porous zirconia ceramics with porosities ranging from 45% to 75%. Typical compressive strength value of microcellular zirconia ceramics with ${\sim}65%$ porosity was over 50 MPa. By adjusting the mixing ratio of large and small zirconia powders, it was possible to control the pore structure from close to open pores.

탄소열환원 공정을 사용한 다공질 탄화규소 세라믹스의 저온 제조공정

엄정혜,장두희,김영욱,송인혁,김해두,Eom, Jung-Hye,Jang, Doo-Hee,Kim, Young-Wook,Song, In-Hyuck,Kim, Hai-Doo 한국세라믹학회 2006 한국세라믹학회지 Vol.43 No.9

A low temperature processing route for fabricating porous SiC ceramics by carbothermal reduction has been demonstrated. Effects of expandable microsphere content, sintering temperature, filler content, and carbon source on microstructure, porosity, compressive strength, cell size, and cell density were investigated in the processing of porous silicon carbide ceramics using expandable microspheres as a pore former. A higher microsphere content led to a higher porosity and a higher cell density. A higher sintering temperature resulted in a decreased porosity because of an enhanced densification. The addition of inert filler increased the porosity, but decreased the cell density. The compressive strength of the porous ceramics decreased with increasing the porosity. Typical compressive strength of porous SiC ceramics with ${\sim}70%$ porosity was ${\sim}13 MPa$.

일정 질소압에서 제조된 반응결합 질화규소에 관한 연구

최명제,노태욱,박찬,박동수,김해두,Choi, Myoung-Je,Roh, Tae-Wook,Park, Chan,Park, Dong-Soo,Kim, Hai-Doo 한국세라믹학회 2000 한국세라믹학회지 Vol.37 No.5

In this investigation, we fabricated RBSN (Reaction Bonded Silicon Nitride) using the static nitriding system which could be advantageous for commercialization. Firstly, Si compacts of different sizes were made, and then nitridation rates were investigated as a function of added static gas pressure. The reaction schedule was obtained by pre-experiments. In case of small samples, the variation of ${\alpha}$, ${\beta}$ phases between the inside and the outside region of the specimens was examined after the samples were nitrided under 1 bar and 1.5 bar reaction pressure. On the other hand, large samples of Si compact with the size of 36 mm for diameter and 23 mm for thickness were nitrided for 26 hours of the total nitridation time, which showed a complete and homogeneous nitriding reaction from the outside to the inside of the samples, although the time was considerably shorter than that needed for convertional nitridation. Nitridation rates obtained at the early stage of reaction were proportional to the reaction gas pressures. The sequences of the nitridation reaction with the thickness were as follows 1) the outside, 2) the inside and 3) the intermediate area of the specimen. These results wer eobtained from the coloration of cross sectioned specimens that had various nitridation rates. Total nitriding reaction kinetics was controlled by chemical reaction, not by diffusion of the nitrogen gas.

기공형성제 크기와 함량이 다공질 지르코니아 세라믹스의 가공율과 강도에 미치는 영향

채수호,김영욱,송인혁,김해두,배지수,Chae, Su-Ho,Kim, Young-Wook,Song, In-Hyuek,Kim, Hai-Doo,Bae, Ji-Soo 한국세라믹학회 2009 한국세라믹학회지 Vol.46 No.1

Using zirconia and poly (methyl methacrylate-coethylene glycol dimethacrylate) (PMMA) microbeads, macroporous zirconia ceramics were fabricated by a simple pressing method. Effects of template size and content on microstructure, porosity, and flexural and compressive strengths were investigated in the processing of the macroporous zirconia ceramics. Three different sizes of microbeads (8, 20, and $50{\mu}m$) were used as a template for fabricating the macroporous ceramics. The porosity increased with increasing the template size at the same template content. The flexural and compressive strengths were primarily influenced by the porosity rather than the template size. However, the strengths increased with decreasing the template size at the same porosity. By controlling the template size and content, it was possible to produce macroporous zirconia ceramics with porosities ranging from 58% to 75%. Typical flexural and compressive strength values at 60% porosity were ${\sim}30\;MPa$ and ${\sim}75\;MPa$, respectively.

Frit 함량이 다공질 Frit-Bonded 알루미나 세라믹스의 미세조직과 꺾임강도에 미치는 영향

임광영,김영욱,송인혁,김해두,배지수,Lim, Kwang-Young,Kim, Young-Wook,Song, In-Hyuck,Kim, Hai-Doo,Bae, Ji-Soo 한국세라믹학회 2010 한국세라믹학회지 Vol.47 No.6

Porous frit-bonded alumina ceramics were fabricated using alumina and frit as raw materials. The effects of frit content and sintering temperature on microstructure, porosity, and flexural strength were investigated at low temperature of $750{\sim}850^{\circ}C$. Increased addition of frit content or higher sintering temperature resulted in improved flexural strength of porous frit-bonded alumina ceramics. It was possible to produce frit-bonded alumina ceramics with porosities ranging from 35% to 40%. A maximum strength of 52MPa was obtained at a porosity of ~38% when 90 wt% alumina and 10 wt% frit powders were used.