안정피로성장 중인 표면균열 형상변화의 해석

주석재,Chu, Seok-Jae 대한기계학회 1996 大韓機械學會論文集A Vol.20 No.9

The multi-point procedure is developed to predict the shape change of a semi-elliptical surface crack during stable fatigue crack growth. 3-D stress intensity factors along a crack front are calculated using the simplified 3-D J-intergral. Crack growth rate coefficient in the Paris law is assumed to be constant along the crack growth. Crack growth rate is set to be the distance between the two parallel tangent lines on the two semi-elliptic crack fronts before and after crack growth.

원격 CO₂ 레이저 용접이음에 대한 피로시험과 해석

주석재,조군,Chu, Seok-Jae,Zhao, Jun 대한기계학회 2012 大韓機械學會論文集A Vol.36 No.10

A remote $CO_2$ laser system can rapidly change both the distance and the direction of the laser beam by moving a lens and rotating mirrors. It is then easy to weld complex patterns of weld lines. A conventional spot weld joint specimen and a remote $CO_2$ laser weld joint specimen with complex weld line patterns were prepared and tested both statically and dynamically. The relationships between the fatigue strength, i. e. the maximum cyclic force, and the fatigue life were obtained. The fatigue strength of the tested welded joints at two million cycles was found to be approximately 10% of the static strength. Furthermore, it was observed that the fatigue fracture mode changed with the level of the applied cyclic force. The fatigue crack origins were confirmed as the highest stress points found in the structural analysis. The maximum cyclic stress for different weld patterns converges as the fatigue life approaches two million cycles. 원격 $CO_2$ 레이저는 렌즈와 거울을 사용하여 신속하게 레이저 빔을 편향시키므로 복잡한 패턴을 그리기 쉽다. 기존 점용접 시편과 원격 $CO_2$ 레이저 여러 가지 용접선 패턴 시편을 준비하여 정적인장시험과 동적피로시험을 수행하였다. 피로수명(피로파단까지 하중반복횟수)에 대한 피로강도(최대피로하중) 데이터를 얻었다. 수명 이백만 회일 때 피로강도는 대체로 정적 인장강도의 10%이었다. 그리고, 피로하중 수준에 따라 피로파괴형태가 달라지는 것을 발견하였다. 구조해석 결과 응력이 높은 부위와 피로균열 발생부위가 일치하는 것으로 확인되었다. 수명 이백만 회일 때 모든 용접선 패턴에 대하여 최대응력이 서로 비슷하여지는 것을 확인하였다.

오스템퍼 연성주철을 적용한 너클

주석재(Seok Jae Chu),김강민(Gang Min Kim),이진훈(Jin Hun Lee) 한국자동차공학회 2008 한국자동차공학회 지부 학술대회 논문집 Vol.2008 No.11

The austempering heat treatment of the ductile iron increases the strength considerably while the elongation is not decreased. The application of the austempered ductile iron to the knuckle is examined in this paper. The austempering condition is modified several times until the required material properties are obtained. The fatigue properties are obtained both from the strain controlled fatigue tests and the stress controlled fatigue tests. The fatigue strength varies according to the austempering conditions. The fatigue analysis of the knuckle is carried out and compared to the fatigue test results.

점용접점을 통하여 전달되는 힘과 모멘트를 이용한 점용접 시편의 피로수명 예측

주석재(Seok-Jae Chu),최병길(Byung-Gil Choi),주영우(Young-Woo Chu),고재경(Je-Kyung Ko),이영우(Young-Woo Lee) 한국자동차공학회 1999 한국자동차공학회 학술강연 논문집 Vol.1999 No.5B

원격 CO₂ 레이저 용접이음에 대한 피로시험과 해석

주석재(Seok Jae Chu),조군(Jun Zhao) 대한기계학회 2012 大韓機械學會論文集A Vol.36 No.10

원격 CO₂ 레이저는 렌즈와 거울을 사용하여 신속하게 레이저 빔을 편향시키므로 복잡한 패턴을 그리기 쉽다. 기존 점용접 시편과 원격 CO₂ 레이저 여러 가지 용접선 패턴 시편을 준비하여 정적인장시험과 동적피로시험을 수행하였다. 피로수명(피로파단까지 하중반복횟수)에 대한 피로강도(최대피로하중) 데이터를 얻었다. 수명 이백만 회일 때 피로강도는 대체로 정적 인장강도의 10%이었다. 그리고, 피로하중 수준에 따라 피로파괴형태가 달라지는 것을 발견하였다. 구조해석 결과 응력이 높은 부위와 피로균열 발생부위가 일치하는 것으로 확인되었다. 수명 이백만 회일 때 모든 용접선 패턴에 대하여 최대응력이 서로 비슷하여지는 것을 확인하였다. A remote CO₂ laser system can rapidly change both the distance and the direction of the laser beam by moving a lens and rotating mirrors. It is then easy to weld complex patterns of weld lines. A conventional spot weld joint specimen and a remote CO₂ laser weld joint specimen with complex weld line patterns were prepared and tested both statically and dynamically. The relationships between the fatigue strength, i. e. the maximum cyclic force, and the fatigue life were obtained. The fatigue strength of the tested welded joints at two million cycles was found to be approximately 10% of the static strength. Furthermore, it was observed that the fatigue fracture mode changed with the level of the applied cyclic force. The fatigue crack origins were confirmed as the highest stress points found in the structural analysis. The maximum cyclic stress for different weld patterns converges as the fatigue life approaches two million cycles.

파괴인성시험의 유한요소 시뮬레이션

주석재(Seok Jae Chu),류총호(Conghao Liu) 대한기계학회 2013 大韓機械學會論文集A Vol.37 No.4

인장시험을 유한요소 시뮬레이션하여 등가응력-등가소성변형률 곡선, 임계 등가응력과 임계 등가소성변형률을 결정하였다. 그리고, 이 곡선을 입력하여 파괴시험을 유한요소 시뮬레이션하여 평면변형률 파괴인성치를 결정하여 보려고 하였다. 균열선단절점에서 등가소성변형률이 임계 등가소성변형률에 도달할 때 균열개구변위를 임계 균열개구변위로 취하여 균열성장조건으로 사용되었다. 임계 등가소성변형률이나 단면감소율과 파괴시험 임계 균열개구변위와 관련성을 찾아보고, 임계 등가응력과 임계 등가소성변형률을 동시에 적용하여 파괴시험 파괴인성치와의 관련성도 찾아보았다. Finite element simulations of tensile tests were performed to determine the equivalent stress ? equivalent plastic strain curves, critical equivalent stresses, and critical equivalent plastic strains. Then, the curves were used as inputs to finite element simulations of fracture toughness tests to determine the plane strain fracture toughness. The critical COD was taken as the COD when the equivalent plastic strain at the crack tip reached a critical value, and it was used as a crack growth criterion. The relationship between the critical COD and the critical equivalent plastic strain or the reduction of area was found. The relationship between the plane strain fracture toughness and the product of the critical equivalent stress and the critical equivalent plastic strain was also found.

알루미늄 압출판재의 프레스성형 중 파열조건에 대한 조사

주석재(Seok Jae Chu),박창구(Chang Gu Park),조은화(Eun Hwa Cho) 대한기계학회 2014 大韓機械學會論文集A Vol.38 No.3

선루프 트랙은 알루미늄을 압출하고 프레스성형하여 생산한다. 프레스성형 중 날카롭게 굽혀진 좌면의 가장자리를 따라 균열이 발생하였다. 좌면의 가장자리를 절단하여 펀치와 다이 모서리의 최종위치를 측정하고 균열발생과의 관계를 조사하였다. 그리고, 이 최종위치까지 굽힘을 유한요소 시뮬레이션하여 임계변형률을 구하였다. 한편, 소재의 방향, 경도, 굽힘 가장자리 길이, 굽힘반경의 여러 가지 다른 조합에 대하여 3점굽힘시험을 수행하였다. 그리고, 3점굽힘시험에 대한 유한요소 시뮬레이션을 수행하여 임계변형률을 구하여 비교하였다. Sunroof tracks are manufactured by press-forming extruded aluminum sheets. During press forming, cracking occurs along the sharply bent edge. The final positions of the punch and die were measured on the section, and their relation to cracking was investigated. Finite element simulation of bending to the final position was done to find the critical strains. Three-point bending tests with different material orientations, hardnesses, bending edge lengths, and bending radii were carried out in the laboratory, and finite element simulation of the three-point bending tests was performed to find the critical strains.

피로균열성장의 유한요소 시뮬레이션

주석재(Seok Jae Chu),유총호(Conghao Liu) 대한기계학회 2012 大韓機械學會論文集A Vol.36 No.7

피로균열성장을 유한요소 시뮬레이션하였다. 인장시험으로 얻는 기계적 성질만을 사용하여 피로균열성장거동을 예측하려고 하였다. 유한요소해석 결과 균열선단 부근 절점의 변위의 변화를 살펴 임계균열개구변위를 결정하였다. 균열선단 절점을 분리하여 균열성장을 시뮬레이션하였다. Paris 법칙의 지수를 결정하여 이미 발표된 값과 비교하였다. 균열닫힘을 고려한 유효 응력확대계수에 관하여 그렸을때 더 일관성이 있는 결과를 얻었다. The finite element simulations of fatigue crack growth are carried out. Using only the mechanical properties usually obtained from the tensile test as input data, we attempted to predict the fatigue crack growth behavior. The critical crack opening displacement is determined by monitoring the change in displacements at the node close to the crack tip. Crack growth is simulated by debonding the crack tip node. The exponent in the Paris law was determined and compared to the published exponent. Plotting with respect to the effective stress intensity factor range yielded more consistent results.

X 리프트 스핀들의 파괴해석

주석재(Seok Jae Chu) 대한기계학회 2008 大韓機械學會論文集A Vol.32 No.1

One of the two spindles in the X-lift fractured suddenly during normal operation. The fracture occurred at the notch where the bending moment might be the maximum. Macrofractographic features associated with rotating-bending fatigue are evident on the fracture surface. The 3-D finite element analysis of the X-lift reveals that the spindle rotated under bending. The measured surface strain of the spindle varies cyclically as the spindle rotates. It supports that the spindle rotated under bending. The X-lift is not perfectly symmetrical with respect to both the horizontal and the vertical plane. The slightly unsymmetrical deformation can cause the bending of the spindle.

배기계 용접이음의 고온피로강도

주석재(Seok Jae Chu),이한용(Han Yong Lee),남궁규완(Nam Koong Kyu Wan) 대한기계학회 2008 大韓機械學會論文集A Vol.32 No.11

The exhaust systems are usually subjected to vibration or shock at high temperatures. The high temperature fatigue tests of the exhaust systems are rarely performed in domestic industries due to limited number of test facility and high test costs. In this paper, the high temperature fatigue test of some part of the exhaust system, not the whole system, is carried out. The resonator located at the central range is heated in the cylindrical electric furnace and the alternating load is applied on the end of the pipe welded to the resonator. The high temperature fatigue strength of the welded joint is obtained. The location of the fatigue crack is different to that in room temperature.