http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
Reducing technology of fuel-NOx generation using fuel-rich/-lean catalytic combustion
S.K. Kang(강성규),S.J. Lee(이승재),I.S. Ryu(유인수),H.D. Shin(신현동),H.S. Han(한헌식) 한국연소학회 2006 KOSCOSYMPOSIUM논문집 Vol.- No.-
A two-step fuel-rich/fuel-lean catalytic combustion seems to be one of the most effective methods to control simultaneously the NO generation and the hydrocarbon (HC) conversion from fuel-bound nitrogen. By controlling equivalent air ratio for maintaining fuel-rich and fuel-lean condition over each catalytic layer, space velocity, inlet temperature, and catalyst component, the HCand ammonia conversion efficiency higher than 95% could be achieved, with ammonia conversion to NO remaining below 5%. The experimental results wouldbe applied to the combustion of land fill gas and to gasified refuse-derived fuels as a method of minimizing NO generation.
Pt, Pd와 Ph가 담지된 촉매상에서 암모니아와 수소/일산화탄소의 단계별 촉매연소에 관한 연구
황주연(J. Y. Hwang),유인수(I.S. Ryu),이규철(K. C. Lee),이승재(S.J. Lee),노동순(D. S. Noh),이관석(K. S. Rhee),강성규(S.K. Kang) 한국연소학회 2006 KOSCOSYMPOSIUM논문집 Vol.- No.-
본 연구는 Fuel-Nox 제어를 위한 암모니아 중 질소성분의 전환반응에 대한 실험 결과이다. 특히 열분해가스 촉매연소에서 NOx 생성을 줄이기 위한 제어 조건을 제시하였으며, Fuel-NOx 반응 메카니즘 연구의 기초자료를 제시하였다. This study investigated on the conversion of nitrogen component in ammonia gas to control fuel-NOx. Control conditions were found to suppress the production of NOx in the catalytic combustion of the gasified fuels. Also, the results would provide the basis of the theoretical study on fuel-NOx generation mechanism.
강성규(S.K. Kang),이승재(S.J. Lee),유인수(I.S. Ryu),이규철(K. C. Lee) 한국연소학회 2007 한국연소학회지 Vol.12 No.4
Utilization of sewage sludge for industrial fuel should be considered in appropriate calory with low emission of environmental pollutants and the amount of sewage sludge for continuously long-time operation. For the low grade fuel(<4,000kcal/㎏), one of proper processes is that coal and oil are added into sewage sludge to remove impurities and increase calory(>7,000kcal/㎏) and the amount of fuel having sewage sludge. Recently, 2-step agglomeration has been attempted by secondarily agglomerate sewage sludge onto the primary nuclei formed by agglomeration of coal and oil. Furthermore, sawdust and waste oil can substitute about 1/3 each for coal and mineral oil consumed in this process, which will lead to securing alternative energy resources from environmental pollutants as well as cost reduction.
김용우(Y.W. Kim),이재근(J.G. Lee),유인수(I.S. Ryu),이승재(S.J. Lee),문승현(S.H. Moon) 한국열환경공학회 2010 한국열환경공학회 학술대회지 Vol.2010 No.춘계
수분의 함량이 높은 저등급 석탄을 유중건조법으로 건조하였고, 건조해서 나온 석탄으로 성형을 하였다. 이때 성형된 펠렛의 파쇄강도를 증가시키기 위한 최적의 조건을 선정하기 위해 실험을 수행하였는데, 실험은 건조조건과 관련된 변수로 비닐함량과 등유증발 온도를 변화 시켰고, 성형 조건과 관련된 변수로는 성형 압력, 성형시간, 성형온도, 성형후 냉각시간에 변화를 주어 수행하였다. 비닐함량이 0.2wt%에서 0.5wt%로 증가함에 따라 성형 펠렛의 파쇄강도가 증가하였으며 0.5wt%에서 0.8wt% 증가에는 큰 변화가 없었다. 등유증발온도는 110℃에서 130℃로 증가함에 따라 성형 펠렛의 파쇄강도가 미세하지만 증가하였으며 150℃에서 증발시킬 경우 오히려 강도가 감소하였다. 성형압력은 80kgf/cm2에서 100 kgf/cm2증가시킴에 따라 성형 펠렛의 파쇄강도가 증가하였으며, 120kgf/cm2까지 증가 하였을 경우 강도가 다시 감소하였다. 성형시간 또한 20sec에서 40sec로 증가 하였을 경우 성형 펠렛의 파쇄강도는 증가하였으며, 60sec로 더 증가 하였을 경우에는 강도가 감소하였다. 따라서 성형시 필요한 등유증발온도나 압력, 시간을 무조건 증가시킨다고 성형 펠렛의 파쇄강도가 강해지는 것은 아닌 것으로 판단된다. 또한, 성형온도가 증가할수록 성형 펠렛의 파쇄강도가 증가하였으며, 성형후 냉각시간을 10min 단위로 증가 시켰을 때 20min까지는 성형 펠렛의 파쇄강도가 증가하였으나 20min 이후부터는 냉각을 해도 파쇄강도에는 큰 변화가 없었다.
폐목재 소각로발생 NOx 저감용 SCR 촉매의 피독 및 재생 연구
이재근(J.G. Lee),김용우(Y.W. Kim),유인수(I.S. Ryu),이승재(S.J. Lee),문승현(S.H. Moon) 한국열환경공학회 2010 한국열환경공학회 학술대회지 Vol.2010 No.춘계
폐목재 소각로에서 발생하는 NOx를 저감하기 위하여 사용되는 SCR 촉매의 피독과 재생에 대하여 조사하였다. TiO2, WO3, V2O5으로 구성된 Honeycomb SCR 촉매는 주로 배가스의 탄소 성분에 의하여 비활성화되는 것으로 나타났다. 이와 같이 비활성화된 SCR 촉매는 공기 중에서 400℃ 이상으로 가열하여 촉매에 존재하는 탄소성분을 연소시킴으로써, 촉매가 원래의 활성 상태로 재생되는 것을 확인하였다