http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
- 中文 을 입력하시려면 zhongwen을 입력하시고 space를누르시면됩니다.
- 北京 을 입력하시려면 beijing을 입력하시고 space를 누르시면 됩니다.
RISS 인기검색어
- 검색키워드
- 저자 : 안삼근 (검색결과 3 건)
- 무료
- 기관 내 무료
- 유료
-
안삼근,강형철,안상열,이균필,변희섭 경상대학교 농업생명과학연구원 2002 농업생명과학연구 Vol.36 No.4
본 연구는 집성 염색 무니목 개발을 위하여 사용 가능한 수종과 3종류의 염료를 사용하여 염색시간, 염색온도, 함수율 및 Flitch 제작에 대하여 연구한 결과는 다음과 같다. 실험에 사용한 4수종 중에서 선삭성이 불량한 은수원 사시나무를 제외한 3수종인 소나무와 이태리 포플러, 마티카가 사용 가능한 수종으로 밝혀졌다. Stain은 번지거나 얼룩이 지는 현상, Dylon은 침투 불균일로 부적당하였으나 Fine은 염색상태가 양호하였다. 염색시간은 5시간 이상 되어야 염색정도가 양호하였고, 염색온도는 90℃에서 가장 적당하였으며 생재와 기건재 및 포수재에 대한 영향은 큰 차이가 없었다. Flitch제작에 적당한 함수율은 9%이었다. This study was carried out to develop laminated dyeing wood, for which usable three sixties of trees and 3 kinds of dye stuffs were used to investigate dyeing time, dyeing temperature, moisture content and manufacture of flitch, the results were as follows: Out of four species of trees used in the experiment, it was found that three species, Pinus densiflora, Populus euramercana and Dyrea costulata were usable excluding Populus tomentiglandulosa whose cutting ability was bad. As to influence according to the kind of dye stuff, the Stain of low price could be used as a coloring agent but it was not proper as a dyeing agent due to spreading or staining phenomenon. As Dylon which was generally used to dye textile penetrated them uneven, dyeing only their surface, it was also found improper to be used. On the other hand, the dyed condition was good with Fine. The dyed condition was good when dyeing time was more than 5 hours and it was the most adequate when the temperature was at 90℃. There was no significant difference between their influence on green, dried and saturated wood.-In the manufacture of Flitch, the most appropriate moisture content was 9%.
-
-
김종만,변희섭,안삼근 한국목재공학회 1999 목재공학 Vol.27 No.1
This paper describes the relationship between the bending strength properties of sloped finger jointed woods and the acoustic emissions (AEs) generated during the test. Pinus densiflora pieces were cut in sloped-finger types and glued with four kinds of adhesives (polyvinyl acetate, polyvinyl-acryl, oilic urethane and resorcinol-phenol resin). The results were as follows: The lower the bending strength(load) was, the earlier the generation time of AE event count got and the higher the increasing rate of AE event count became in the sloped finger jointed specimens bonded with polyvinyl acetate and oilic urethane resin adhesives. Therefore, the slope from load-AE cumulative event count curve was very steep. The AE event count for resorcinol-phenol resin adhesive obtained even from low load level was abundant. The AE event count continuously increased as load increased and the event count was much more than one in the other conditions. The slope from load-AE cumulative event count curve was very gentle compared with other conditions. The patterns of AE event count and count were very similar. The relationship between the MOR and the AE parameter from load and AE cumulative event count in the early stage of the sloped finger jointed specimens bonded with polyvinyl acetate, oilic urethane and resorcinol-phenol resin adhesives was much greater than that between the MOE and the MOR. Therefore, the AE signals obtained during bending test are useful for estimating the strength of sloped finger jointed specimens.
RISS
코리아스칼라연관 검색어 추천
이 검색어로 많이 본 자료
활용도 높은 자료
