http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
봉상접지극과 Mesh접지극의 매설깊이 변화에 따른 위험전압 분석에 관한 연구
심용식(Yong-Sik Shim),최홍규(Hong-Kyoo Choi) 한국조명·전기설비학회 2011 조명·전기설비학회논문지 Vol.25 No.4
Grounding electrodes with higher burial depths are evaluated to have better performance, due to the domestic practice that puts the grounding resistance as the standard of performance evaluation, while grounding resistance decreases as the burial depth increases. However, The dangerous voltage is necessary for the analysis. Because the performance evaluation of grounding electrodes should include not only grounding resistance but also the dangerous voltage(mesh voltage and step voltage). So in this paper, The dangerous voltages of mesh grounding and rod grounding were analyzed for using computer simulation and miniature grounding model.
메쉬접지극의 내부도체 배치에 따른 개선된 메쉬접지극 모델
심용식(Yong-Sik Shim),최홍규(Hong-Kyoo Choi),김태훈(Tae-Hoon Kim),송영주(Young-Joo Song) 한국조명·전기설비학회 2010 조명·전기설비학회논문지 Vol.24 No.6
국내?외 메쉬접지극은 격자형태의 등간격 접지Grid로 설계하고 있다. 격자형 접지Grid의 경우 구석의 접촉전압이 중심 부분에 비해 높아지는 문제점이 있다. 이러한 문제점을 극복하기 위해 사선형태의 접지 Grid를 사용하면 메쉬전압이 발생하는 구석부분의 면적이 감소함으로써 메쉬전압이 감소한다. 따라서 본 논문에서는 기존의 격자형태의 접지Grid의 형태와 다르게 사선형태의 접지Grid를 제안하며, 격자형태의 접지Grid와 사선형태의 접지Grid로 설계된 메쉬접지극에 동일한 접지설계제원을 적용하고 메쉬전압, GPR, 접지저항, 접지도체의 총길이를 비교 검토하여 사선형태 접지Grid의 우수성을 검증하였다. Mesh grounding electrodes in Korea and abroad are designed as lattice-shaped equidistance grounding grids. In case of a lattice-shaped grounding Grid, however, there is a problem of higher touch voltage at the corner of the grid relative to the center. To overcome this problem, we used oblique-shaped equidistance grounding grid to reduce the area of the corner where mesh voltage occurs. As a result the mesh voltage was reduced. Therefore, this paper suggests the use of oblique-shaped grounding grid instead of the existing lattice-shaped ones. It applied the same grounding design dimensions for both lattice-shaped and oblique-shaped grounding grids, compared and analyzed mesh voltage, GPR, ground resistance, total length of grounding conductor, verified that oblique-shaped grounding grid is superior to the lattice-shaped.
손석금(Seok-Geum Son),김재철(Jae-Chul Kim) 한국조명·전기설비학회 2011 조명·전기설비학회논문지 Vol.25 No.11
In Korea, characterized in most cases by limited area or high earth resistivity, it is likely to design narrow distances between grounding conductors, with a view to keeping ground resistance and touch voltage below the safety margin values. A new grounding method is suggested, making use of double meshes, to lower touch voltage in a confined area, since it is difficult to lay the plugs under the ground with narrow gaps between them on a limited site. For the presentation of a new model, the suggested grounding system has been analyzed and studied in ground resistance, touch voltage and step voltage, using IEEE Std. 80 calculations and computer simulations.
제한된 부지 다층 대지구조에서 위험전압을 고려한 접지설계
손석금(Seok-Geum Son) 대한전기학회 2013 전기학회논문지 P Vol.62 No.3
In Korea, where most of the sites are narrow in space and their earth resistivity is relatively high, the spaces between grounding conductors are likely to be designed narrow in order to lower ground resistance and dangerous voltage below to the permitted safety values. In addition, ground nets are in the shape of square or rectangle depending on the location and size of the facilities and ground contact area, and inner conductors are laid out in grids like the pattern of nets. Nevertheless, with the existing designs, the marginal voltage for safety gets higher as the area is extended further outside, in comparison with that of inner mesh grounding, thus causing much difficulty maintaining them equipotential, and there exist limits in the burial, grounding grid design considering the dangerous voltage of muti-layered model in the constrained sites, was studied.
손석금(Seok-Geum Son),김재철(Jae-Chul Kim) 대한전기학회 2011 전기학회논문지 P Vol.60 No.3
When we design the grounding grid, dangerous voltage ANSI/IEEE Std. 80 method has been commonly used in the domestic area. However, the suitability of the ground rules for the design environment available. However, the suitability of the ground rules for the design environment available. In this paper, sticks according to the electrode conductor in combination with the mesh in order to design the ground by the IEEE Std.80 was designed. So in this paper, we examined of IEEE Std. 80 touch voltage method marginal utility and we induced for those problems by comparison between IEEE Std. 80 touch voltage value and simulation experimentation value. Furthermore, this paper presents a new design grounding system method that complements the IEEE Std. 80 method.