http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
매스콘크리트의 수화열 저감을 위한 단열온도상승시험 및 모의시험체의 온도특성
연규원,김종 대한건축학회지회연합회 2012 대한건축학회연합논문집 Vol.14 No.2
본 연구에서는 건축물 매트기초 매스콘크리트의 수화열 저감 및 경제성 성취에 활용될 수 있도록 배합종류 변화에 따른 단열온도상승특성과 모의부재 실험을 통하여 적용가능성에 대하여 검토하고자 하였다. 실험 결과에 따르면 먼저, 단열온도상승 특성으로 배합 종류에 따라 단열온도상승식을 근사식 을 검토하여 결정계수(R2) 0.994이상이 되는 식을 얻을 수 있었으며, 각 배합에 따라 최고 온도상승량과 수화반응에 의한 발열시점을 보다 정확히 확인 할 수 있었다. 모의부재의 수화열 온도이력 특성으로 모의부재 C의 경우 모의부재 A와 비교 하여, 최고온도는 약 7.5℃ 저감 시켰다. 또한 상부콘크리트가 먼저 수화발열함으로서 표면부의 인장응력에 대한 온도균열을 제어 할 수 있는 것으로 나타났다. 압축강도 특성으로 배합종류별 표준양생공시체의 경우 플라이애시를 치환한 S-F30, R-F30콘크리트는 치환하지 않은 S-P, E-P콘크리트 보다 압축강도가 약 5~10MPa정도 재령 28에서 저하된 것으로 나타났으나, 코어압축강도의 경우에서는 플라이애시 치환사용에 따른 차이가 없는 것으로 분석되었다.
플라이애시 치환율 변화에 따른 매스콘크리트의 간이단열온도상승 특성과 타설 시간차를 고려한 수화열 해석
연규원,박찬수 대한건축학회지회연합회 2013 대한건축학회연합논문집 Vol.15 No.3
본 연구는 플라이애시 치환율을 변화에 따른 매스콘크리트의 간이단열온도상승 특성과 타설시간차를 고려하여 수화열을 해석하고, 상하부 콘크리트간의 배합을 조정하여 온도균열지수 및 균열발생확률을 비교 검토하였는데 그 결과를 요약하면 다음과 같다. 간이단열온도상승 특성으로 FA 치환율별 단열온도상승식 은 콘크리트의 초기 휴지기를 고려함에 따라 결정계수 R2=0.99이상의 양호한 값으로 나타났으며, 본 실험결과로 인해 수화발열상승량과 발열시점을 보다 정확히 확인 할 수 있었고, Plain과 FA 40% 치환콘크리트간에는 약 13.2℃의 수화발열량차가 발생함을 확인할 수 있었다. 수화열 해석 특성은 응결시간 및 발열량차를 조절하기 위해 상하부 콘크리트의 배합을 변화시켜 모두 12건으로 해석하였으며, 그 중 수화발열량 조정방법에 해당되는 D, E, H, I 및 L모델의 경우 중심부 최고 온도는 42.69~46.65℃이고, 온도균열지수는 0.76~0.96의 결과로 나타났으며, 균열발생확률 또한 15~44%의 양호한 결과로 확인되어, 매스콘크리트의 내·외부 구속에 의한 균열 및 타설초기에 발생하는 온도까지도 제어가 가능한 것으로 확인, 검토되었다.
황산철을 이용한 컬러 모르타르의 공학적 특성에 관한 기초적 연구
연규원,박찬수 대한건축학회지회연합회 2009 대한건축학회연합논문집 Vol.11 No.2
The study tested overall engineering properties of the mortar mixed with iron sulfate, which can replace the expensive pigment and represents colors as well. In the experiment with mortar not hardened, in cases of mixture proportion such as 1:1 or 1:3, the flow test data and air content decreased as iron sulfate increased. However, unit volume weight increased. Setting time is delayed as more iron sulfate is added. The compressive strength of the hardened mortar in 1:1 and 1:3 mixture proportion has improved with 9% or less of iron sulfate and decreased with 12% or more. As for drying shrinkage properties compared with plain and irrespective of mixture proportion, it has decreased with 6% or less of iron sulfate adding and increased with excess of 6%. Meanwhile, in regard to chromaticity, a*b* has increased as iron sulfate being added more and the case of mixture proportion of 1:1 has shown higher a*b* than that of 1:3. The value of a*b* in the mixture proportion of 1:1 was higher outdoors than indoors in the initial ageing period. At the later ageing days, a*b* of indoors remained unchanged but that of outdoors went down sharply to the level of indoors at 28 ageing days. a*b* of the mixture proportion of 1:3 showed no difference between indoors and outdoors at the initial ageing period and thereafter, a*b* of indoors remained stable while a*b* of outdoors went down and even became less than that of indoors at 28 ageing days.
철근콘크리트부재에서 비탄성동작에 따른 횡방향보강근의 구속지수에 대한 연구
박찬수,연규원 충북대학교 건설기술연구소 1998 建設技術論文集 Vol.17 No.2
The reinforced concrete members with lateral reinforcement have more ductile capacity at ultimate condition. The rectangular beams with various volumetric ratio of confined concrete to lateral reinforcement are tested and analyzed in inelastic range. Tests are conducted on 15 rectangular section(150㎜ × 150㎜), far load-deflection relationship, and compared with analytical results The conclusions are summarized as follows. 1. The ductility factor is expressed with ductility energy ratio which is moment-curvature area ratio. 2. The ductility energy ratio of test results are very agreed with analytical values. 3. The confined concrete volumetric ratio of lateral reinforcement is proved the major factor of the ductility energy ratio.