http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
나만균,심영록,정철기,이경진,김승평,정성태,Na, Man-Gyun,Sim, Young-Rok,Jung, Chul-Kee,Lee, Goung-Jin,Kim, Soong-Pyung,Chung, Sung-Tai 대한방사선방어학회 2000 방사선방어학회지 Vol.25 No.2
현재 영광원전에서 정상운전중 기체 방사성물질의 대기확산 평가를 위해 XOQ_DW 코드가 이용되고 있다. 이 코드는 기본적으로 XOQDOQ 코드에 근거하여 개발되었으며, 정상운전 및 사고시 피폭평가를 수행하기 위하여, 사고시 대기확산을 평가하는 방법이 첨가되어야 한다. 사고시 대기확산을 평가하기 위해서 USNRC Reg. Guide 1.145에 기초하여 개발된 PAVAN 코드에 근거하여 가상 사고시 대기확산 코드인 XOQAR 코드가 개발되었다. 이 코드는 XOQ_DW 코드와의 인터페이스를 통하여 XOQ_DW 코드의 입력인 지형 모델 그리고 XOQ_DW 코드의 출력인 연평균 대기확산인자가 본 코드의 입력으로 이용되었다. 본 코드를 이용하여 제한구역경계와 저인구지대 경계에서 대기확산인자 값이 바다방향을 제외한 최대값은 각각 $1.33{\times}10^{-4}$와 $7.66{\times}10^{-6}$ sec/$m^3$이었다. 본 코드의 개발을 통하여 영광원전에서 정상운전 및 사고시 대기확산을 평가할 수 있는 코드 시스템을 갖추게 되었다. 또한 개발된 코드는 산악이 많은 우리나라 다른 발전소에 적용하기 위해 산악지형 입력변경을 통하여 적절히 사용될 수 있을 것이다. XOQ_DW code is currently used to assess the atmospheric dispersion fur the routine releases of radioactive gaseous effluents at Yonggwang nuclear power plants. This code was developed based on XOQDOQ code and an additional code is required to assess the atmospheric dispersion for potential accidental releases. In order to assess the atmospheric dispersion fer the accidental releases, XOQAR code has been developed by using PAVAN code that is based on Reg. Guide 1.145. The terrain data of XOQ_DW code inputs and the relative concentrations (X/Q) of XOQ_DW code outputs are used as the inputs of the XOQAR code through the interface with XOQ_DW code. By using this code, the maximum values of X/Q at exclusion area and low population zone boundaries except for sea areas were assessed as $1.33{\times}10^{-4}$ and $7.66{\times}10^{-6}$ sec/$m^3$, respectively. Through the development of this code, a rode system is prepared for assessing the atmospheric dispersion for the accidental releases as well as the routine releases. This developed code ran be used for other domestic nuclear power plants by modifying the terrain input data.
A Fault Diagnosis and Control Integrated System for an SP-100 Space Reactor
나만균(Man Gyun Na),양헌영(Heon Young Yang),임동혁(Dong Hyuk Lim),이윤준(Yoon Joon Lee) 대한전기학회 2007 대한전기학회 학술대회 논문집 Vol.2007 No.10
In this paper, a fault diagnosis and control integrated system (FDCIS) was developed to control the thermoelectric (TE) power in the SP-100 space reactor. The objectives of the proposed model predictive control were to minimize both the difference between the predicted TE power and the desired power, and the variation of control drum angle that adjusts the control reactivity. Also, the objectives were subject to maximum and minimum control drum angle and maximum drum angle variation speed. A genetic algorithm was used to optimize the model predictive controller. The model predictive controller was integrated with a fault detection and diagnostics algorithm so that the controller can work properly even under input and output measurement faults. With the presence of faults, the control law was reconfigured using online estimates of the measurements. Simulation results of the proposed controller showed that the TE generator power level controlled by the proposed controller could track the target power level effectively even under measurement faults, satisfying all control constraints.
장호섭(Ho-Seob Chang),나만균(Man-Gyun Na),김경석(Koung-Suk Kim) 한국비파괴검사학회 2014 한국비파괴검사학회지 Vol.34 No.1
용접 잔류응력은 용접공정에서 발생하는 하는데, 용접 구조물의 결함 유발 및 파괴의 주요 원인이 된다. 본 논문에서는 전자 처리 레이저 스페클 간섭법을 이용하여 원전 배관의 용접부 잔류응력을 측정하였다. 인장시험기를 이용하여 용접된 배관에 압축 하중을 가하였으며, 면내 변형 측정 간섭계를 이용하여 용접부와 모재부의 변형을 측정하였고, 제안된 수식에 의하여 탄성계수를 측정하였다. 용접 배관에 가해지는 하중에 따라 변형이 일정하게 증가하며, 용접 배관의 모재부와 용접부에 발생한 변형을 비교하였을 때, 모재부의 변형이 더 크게 나타남을 확인할 수 있었다. 용접 배관 모재부의 탄성계수는 202.46 GPa, 용접부의 탄성계수는 212.14 GPa, 잔류응력은 6.29 MPa로 측정되었다. Residual stresses that occur during the welding process, are the main cause of failure and defects in welded structures. This paper, presents the use of an electronic processing laser speckle interferometer to measure the residual stress of a welded pipe for a nuclear power plant. A tensile testing machine was used to evaluate a welded pipe that failed in compression. The inform plane deformation and modulus of elasticity of the base metal and welds were measured using an interferometer. Varying the load on the welded pipe had a larger effect on the deformation of the base metal the other properties of the base metal and welds. The elastic moduli of the base metal and weld of the welded pipe were 202.46 and 212.14 GPa, respectively, the residual stress was measured to be 6.29 MPa.