http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
이근식,김정희 淑明女子大學校 1988 論文集 Vol.28 No.-
The ion of Mg^(2+), Ca^(2+), Cd^(2+) was doped to silver chloride. The sensitivity of doped membrane electrodes were compared to pure silver chloride. The Physical properties of doped membranes were excellent to use for detection of halogen ions. The membrane electrodes showed nernstian slope of 57mV to Cl^- ion in the 1.0×10^(-1) M to 1.0×10^4M and in the Potentiometric precipitation titration curves found that it was better than to pure silver chloride electrode.
상부 암모니아 사이클을 도입한 드라이아이스 제조 사이클의 해석
이근식 울산대학교 1999 공학연구논문집 Vol.30 No.2
대기 중의 이산화탄소를 감소시키는 방법 중의 하나로 암모니아 냉동사이클을 상부 사이클로 하는 드라이아이스 제조 사이클을 고안하여 해석하였다. 상.하부 각 사이클은 2단 압축을 하며 플래쉬 드럼에서 중간냉각함으로써 압축 각 단에 유입되는 질량유량이 달라 진다. 압축 각 단의 압축동력, 질량유량, 출구온도를 이산화탄소의 응축압력에 따라 구하였다. 본 연구에서는 이산화탄소와 암모니아 사이클의 중간압력들을 계산하기 위하여 종래의 이산화탄소의 응축압력(26 bar)를 사용하였다. 그 결과, 종래의 이산화탄소의 응축압력(26bar)은 최소압축동력과 최적의 이산화탄소의 응축압력의 관점에서 충분히 타당한 압력임을 입증하였다. 본 사이클은 수냉식 응축기를 가진 3단 압축 이산화탄소 제조 사이클의 응축압력(63bar)보다 휠씬 낮은 응축압력(19-26bar)으로 작동되며, 상업적인 드라이아이스 제조 시스템 (260kW/(ton/hr) of dry ice)보다 휠씬 낮은 압축동력이 소요되는 장점이 있다. A dry ice cycle with topping ammonia cascade refrigeration was devised and analyzed as a mean of mitigating the CO₂ concentration in the air. The trends of compression power, mass flow rate, and exit temperature of each compressor were investigated as a function of CO₂ condensing pressure. In this cycle,, the conventional design pressure (26 bar)of CO₂condenser was used to calculate the intermediate pressures of both CO₂-cycle and ammonia-cycle. Results show that the conventional design pressure of CO₂ condenser has an enough validity in point of both minimum compression power and optimum CO₂condensing pressure. The present cascade cycle has advantages in much lower CO₂condensing pressure (19-26bar) than that (63bar)of 3-stage compression system using CO₂as both working fluid and refrigerant and much lower compression power (206-208 kW) in comparison with that (260 kW/(tom/hr) of dry ice) of typical commercial dry ice production system.
가스터빈 블레이드 2차원 막냉각 특성에 대한 수치적 연구
손창호,노석만,이근식 울산대학교 2000 공학연구논문집 Vol.31 No.1
고성능 개스터어빈 엔진의 냉각에 널리 채용되고 있는 막냉각 성능에 대한 체계적인 규명을 위하여 분사비, 분사각도, 하류형상의 변화에 따른 연구를 수행하였다. 정렬 격자를 이용하였으며, 분사비는 0.25-5.0, 분사각는 15˚-60˚(15˚씩 증가)에 대해 유동과 열전달 특성을 FLUENT를 이용하여 해석하였다. 물성치를 일정하게 가정한 경우와 온도의 함수로 가정한 경우를 비교하였다. 결과에 의하면, 분사각에 따라 냉각효율(벽면온도 900 K 까지의 도달거리)을 최대로 하는 분사비가 존재하였다. 하류형상을 5d(d는 슬롯 크기)만큼 상승 또는 하강 시키면 냉각효율이 떨어짐이 관측되었다. 일정물성치로 가정한 경우가 온도의 함수로 가정한 것에 비해 냉각성능이 과대평가됨을 알 수 있었다. A numerical study has been performed for the 2-dimensional film cooling employed in the cooling of hot components such as gas trubines. The flow and heat transfer characteristics are numerically simulated using FLUNT software. Blowing ratios vary from 0.25 to 5.0 and coolant injection angles vary from 15˚ to 60˚in 15˚increment. The result shows that, for all cases, there exists a blowing ratio which maximizes film cooling effect (measured by the distance from the slot exit to the downstream wall location at which temperatre increases to 900 K) for a given injection angle. It is also observed that the film cooling effectiveness decreases when downstream wall is sunk or lifted. The simulation has been performed using both constant properties and temperature dependent variable properties. It is found that the case with constant properties overestimates the film cooling effect considerably.
수산화마구네슘 製造에 關한 硏究 : 수산화마구네슘의 沈降容積에 關하여
李根植 淑明女子大學校 1966 論文集 Vol.6 No.-
Magnesium hydroxide obtained from sea water by means of adding sodium hydroxide as precipitator, is in a collidal state and therefore, it is difficult to obtain precipitate within a short time. In order to observe the changes in the volume of magnesium hydroxide precipitate in mother liquor at room temperature, a series of experiments have been conducted on the effects with relation to the concentration of precipitator, the speed and time of agitation, speed of addition of precipitator, the shapes of reaction vessels, inter-relationship between length of time of precipitation and volume of precipitate, etc.