http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
A complementary analysis of the porous structure of biochars obtained from biomass
Kwiatkowski Mirosław,Kalderis Dimitrios 한국탄소학회 2020 Carbon Letters Vol.30 No.3
This paper presents the results of the analysis of the porous structure of biochars produced from biomass, namely eucalyptus, wood chips, pruning waste and rice husk. The structural analysis was carried out using the BET, the t-plot, the NLDFT and the LBET methods, which yielded not only complementary information on the adsorptive properties of obtained biochars from these materials, but also information on the usefulness of the structural analysis methods in question for the research into an effect of the technology of carbonaceous adsorbent preparation.
Tomasz Kwiatkowski,Michal Jedrzejczyk,Afaque Shams Korean Nuclear Society 2024 Nuclear Engineering and Technology Vol.56 No.4
The reactor cavity cooling system (RCCS) is a passive reactor safety system commonly present in the designs of High-Temperature Gas-cooled Reactors (HTGR) that removes heat from the reactor pressure vessel by means of natural convection and radiation. It is one of the factors responsible for ensuring that the reactor does not melt down under any plausible accident scenario. For the simulation of accident scenarios, which are transient phenomena unfolding over a span of up to several days, intermediate fidelity methods and system codes must be employed to limit the models' execution time. These models can quantify radiation heat transfer well, but heat transfer caused by natural convection must be quantified with the use of correlations for the heat transfer coefficient. It is difficult to obtain reliable correlations for HTGR RCCS heat transfer coefficients experimentally due to such a system's size. They could, however, be obtained from high-fidelity steady-state simulations of RCCSs. The Rayleigh number in RCCSs is too high for using a Direct Numerical Simulation (DNS) technique; thus, a Reynolds-Averaged Navier-Stokes (RANS) approach must be employed. There are many RANS models, each performing best under different geometry and fluid flow conditions. To find the most suitable one for simulating an RCCS, the RANS models need to be validated. This work benchmarks various RANS models against three experiments performed on the HTTR RCCS Mockup by the Japanese Atomic Energy Agency (JAEA) in 1993. This facility is a 1/6 scale model of a vessel cooling system (VCS) for the High Temperature Engineering Test Reactor (HTTR), which is operated by JAEA. Multiple RANS models were evaluated on a simplified 2d-axisymmetric geometry. They were found to reproduce the experimental temperature profiles with errors of up to 22% for the lowest temperature benchmark and 15% for the higher temperature benchmarks. The results highlight that the pragmatic turbulence models need to be validated for high Rayleigh natural convection-driven flows and improved accordingly, more publicly available experimental data of RCCS resembling experiments is needed and indicate that a 2d-axisymmetric geometry approximation is likely insufficient to capture all the relevant phenomena in RCCS simulations.
Han, Jeongho,da Silva, Alisson Kwiatkowski,Ponge, Dirk,Raabe, Dierk,Lee, Sang-Min,Lee, Young-Kook,Lee, Sang-In,Hwang, Byoungchul Elsevier 2017 Acta materialia Vol.122 No.-
<P><B>Abstract</B></P> <P>The effects of prior austenite (γ) grain boundaries and microstructural morphology on the impact toughness of an annealed Fe-7Mn-0.1C-0.5Si medium Mn steel were investigated for two different microstructure states, namely, hot-rolled and annealed (HRA) specimens and cold-rolled and annealed (CRA) specimens. Both types of specimens had a dual-phase microstructure consisting of retained austenite (γ<SUB>R</SUB>) and ferrite (α) after intercritical annealing at 640 °C for 30 min. The phase fractions and the chemical composition of γ<SUB>R</SUB> were almost identical in both types of specimens. However, their microstructural morphology was different. The HRA specimens had lath-shaped morphology and the CRA specimens had globular-shaped morphology. We find that both types of specimens showed transition in fracture mode from ductile and partly quasi-cleavage fracture to intergranular fracture with decreasing impact test temperature from room temperature to −196 °C. The HRA specimen had higher ductile to brittle transition temperature and lower low-temperature impact toughness compared to the CRA specimen. This was due to intergranular cracking in the HRA specimens along prior γ grain boundaries decorated by C, Mn and P. In the CRA specimen intergranular cracking occurred along the boundaries of the very fine α and α′ martensite grains. The results reveal that cold working prior to intercritical annealing promotes the elimination of the solute-decorated boundaries of coarse prior γ grains through the recrystallization of αʹ martensite prior to reverse transformation, hence improving the low-temperature impact toughness of medium Mn steel.</P> <P><B>Graphical abstract</B></P> <P>[DISPLAY OMISSION]</P>
Kang, Hyunook,Bang, Injin,Jin, Kyeong Sik,Lee, Boyun,Lee, Junho,Shao, Xiangqiang,Heier, Jonathon A.,Kwiatkowski, Adam V.,Nelson, W. James,Hardin, Jeff,Weis, William I.,Choi, Hee-Jung American Society for Biochemistry and Molecular Bi 2017 The Journal of biological chemistry Vol.292 No.17
<P>Intercellular epithelial junctions formed by classical cadherins, beta-catenin, and the actin-binding protein alpha-catenin link the actin cytoskeletons of adjacent cells into a structural continuum. These assemblies transmit forces through the tissue and respond to intracellular and extracellular signals. However, the mechanisms of junctional assembly and regulation are poorly understood. Studies of cadherin-catenin assembly in a number of metazoans have revealed both similarities and unexpected differences in the biochemical properties of the cadherin center dot catenin complex that likely reflect the developmental and environmental requirements of different tissues and organisms. Here, we report the structural and biochemical characterization of HMP-1, the Caenorhabditis elegans alpha-catenin homolog, and compare it with mammalian alpha-catenin. HMP-1 shares overall similarity in structure and actin-binding properties, but displayed differences in conformational flexibility and allosteric regulation from mammalian alpha-catenin. HMP-1 bound filamentous actin with an affinity in the single micromolar range, even when complexed with the beta-catenin homolog HMP-2 or when present in a complex of HMP-2 and the cadherin homolog HMR-1, indicating that HMP-1 binding to F-actin is not allosterically regulated by the HMP-2.HMR-1 complex. The middle (i.e. M) domain of HMP-1 appeared to be less conformationally flexible than mammalian alpha-catenin, which may underlie the dampened effect of HMP-2 binding on HMP-1 actin-binding activity compared with that of the mammalian homolog. In conclusion, our data indicate that HMP-1 constitutively binds beta-catenin and F-actin, and although the overall structure and function of HMP-1 and related alpha-catenins are similar, the vertebrate proteins appear to be under more complex conformational regulation.</P>