http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
SCM415강의 열처리 변형제어를 위한 냉각 매질의 특성
안민주(Min-ju Ahn),류성기(Sung-ki Lyu) 한국기계가공학회 2010 한국기계가공학회지 Vol.9 No.6
This study deals with the characteristic of refrigerant for heat-treatment deformation control of SCM415 steel. The control of heat-treatment deformation must need the progress of production parts for an industry machine. Most of the deformation is occurred on unequal cooling. The unequal cooling is occurred by a property of quenching refrigeration. When a heated metal is deposited in the refrigeration, the cooling speed is so slow in early period of cooling because of occurring a steam-curtain. After more cooling, the steam-curtain is destroyed. In this progress, the cooling speed is very fast. The object of this study is to control the deformation of heat-treatment for the part of the industry machine by improving the conditions of quenching. The cooling curves and cooling rates of water, oil and polymer solution are obtained and illustrated. From the characteristics of the quenching refrigerant, the effects of heat-treatments on the thermal deformation and fatigue strength are also investigated.
안민주(Min-Ju Ahn),안인효(In-Hyo Ahn),류성기(Sung-Ki Lyu) 한국기계가공학회 2011 한국기계가공학회지 Vol.10 No.1
The main objective of this paper is obtaining the optimal carburizing hours which impacts geometric tolerances, OPD(Over Pin Diameter), runout, hardness and fatigure strength of SCM415 spur gear. In order to observe the deformation of the gear, the circularity, squareness, OPD(Over Pin Diameter) and runout were measured at 3hour, 4hour and 5hour respectively. As the result, the 3hour situation is the best, which very similar with the 4hour one. Afterwards, with the purpose of getting the result of gear hardness, the surface hardness, maximum hardness and interior hardness were measured. The result is 5h situation is the best, and it's similar with 4hour one. At last, the fatigue tests have been done which receive the result that the 4h situation showed 9~12% fatigue strength improvement compared with the 3h and 5h ones. To sum up the results, the 4hour situation shows the best performance in accuracy, hardness and fatigue strength.
선형적 요소 예측을 통한 비선형 시스템 동적 특성 연구
안민주(Min-ju Ahn),류성기(Sung-ki Lyu),윤종윤(Jong-yun Yoon),장기(Zhang-Qi),안인효(In-hyo Ahn) 한국기계가공학회 2010 한국기계가공학회지 Vol.9 No.2
The characteristics of the torsional systems are generally examined with the nonlinearities such as the several staged clutch damper springs, gear backlashes and drag torques. Generally speaking, the system's characteristics can be found out by the eigensolutions which can show the system natural frequencies and the mode shapes. However, these factors can not give the complete solutions to avoid the noise and vibration problems related to the nonlinear effects. Therefore, several assumptions should be made for solving the real physical system problems under the linear analysis which can reflect the nonlinear effects in the torsional system. This means that the several modified linear factors such as the modified clutch damper spring constants can be used to examine and avoid the natural frequency zones related to the noise and vibration problems. Under the linear analysis with the assumed and modified values, the system can be investigated with the more reliable ways for the realistic phenomena.
안민주(Min-Ju Ahn),안인효(In-Hyo Ahn),장기(Qi Zhang),류성기(Sung-Ki Lyu) 한국기계가공학회 2011 한국기계가공학회지 Vol.10 No.2
This paper studied the carburizing of chromium molybdenum steel which the heat treatment effect of gear geometric tolerance, OPD, Runout, the surface hardness, the maximum hardness, the core hardness and the bending fatigue strength were investigated. Firstly, the deformation is observed, and the results of circularity, squareness, OPD and Runout of SCM822, SCM425, and SCM415 are obtained in order. Secondly, in order to investigate the gear hardness, the surface hardness, the maximum hardness and the core hardness of SCM822, SCM425, and SCM415 are obtained; and the surface hardness of SCM822 is about 10% higher than SCM415’s, and about 3% higher than SCM425’s. Thirdly, the fatigue strength of SCM822 is about 10% higher than SCM415’s, and about 7% higher than SCM425’s in the fatigue test results. At last, for the purpose of the minimum deformation of heat treatment, and also the improvement of fatigue strength, the best gear material is SCM822 in this test.
상악 구치부의 발치와 동시에 시행하는 상악동저 증강술을 이용한 임프란트 증례
김민규,진민주,안은주,Kim, Min-Kue,Jin, Min-Ju,Ahn, Eun-Joo 대한치주과학회 2007 Journal of Periodontal & Implant Science Vol.37 No.3
Rapid crestal bone resorption following maxillary tooth loss is further accentuated in the posterior regions because of pneumatization and enlargement of the maxillary sinuses. A treatment rationale that allows preservation and augmentation of vertical available bone at the time of posterior maxil-lary tooth extraction may offer numerous therapeutic benefits which are more short courses of ther-apy and no needs of additional surgical augmentation. The present study comprised 3 patients who had 4 posterior maxillary teeth with no evident bone between the tooth apex and sinus floor, as estimated through preoperative radiographic analysis. Sinus floor augmentation at the time of tooth extraction was chosen for the ltreatment of these patients. After the tooth was carefully extracted, the empty alveolus was thoroughly debrided and a trephine approach was performed. Particulated autogenous bone was gently pushed beyond the empty alveolus to elevate the sinus membrane using an osteotome. The distance between bone crest and si-nus floor was radiographically estimated 4 months after the first procedure. Another procedure was then carried out to place the implants of 11 mm length without another augmentation procedure. All implant were clinically stable, with no sign of infection. The presented surgical procedure performed at the time of extraction of posterior maxillary teeth in close proximity to the sinus floor allowed placement of implants of proper length.
안인효(In-Hyo An),안민주(Min-Ju Ahn),허철수(Zhezhu Xu),류성기(Sung-Ki Lyu) 한국기계가공학회 2011 한국기계가공학회지 Vol.10 No.3
This study deals with the effect of the honing in SCM420H planetary gears. The hardness, tooth profile, lead and roughness of the gear surface can be improved by honing. Therein, the honing techniques are welcomed especially as one of the physical surface improvement methods. As a result, gear honing reduces vibration and noise, and will increase the life of gear. And gear honing also changes the surface of gear tooth in a short time and price, so it is a very important method in manufacturing industry. But nowadays, it is hard to find the detail information of gear honing. The test gear is a planetary gear which is used in the automotive industry. It is manufactured by the hobbing, shaving, carburizing and honing. This study investigates the effect of honing in surface shape of SCM420H planetary gears, including fatigue strength test and characteristics of honing of SCM420H planetary gears.
류성기 ( Sung Ki Lyu ),안민주 ( Min Ju Ahn ),안인효 ( In Hyo Ahn ) 한국안전학회(구 한국산업안전학회) 2011 한국안전학회지 Vol.26 No.1
This study deals with the effect of the shot peening in SCM420H planetary gears. The hardness and roughness of the gear surface can be improved by shot blast and shot peening. there in, the shot peening techniques are welcomed especially as one of the physical surface improvement methods. The two treatments are used widely, because of the qualitative analysis of shot blast and shot peening has become possible and the surface treatment can be done with little costs compared with other surface improvement methods. Therefore, this study investigates the effects of shot blast and shot peening in surface shape. The fatigue strength test at a constant stress amplitude is performed by using an electrohydraulic serve-controlled pulsating tester. And fatigue test also explained characteristics of shot blast and shot peening of planetary gears.