http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
히트싱크를 결합한 보상실을 갖는 평판형 양방향 루프히트파이프(FBELHP)의 운전특성 연구
김태희(Tae Hee Kim),마성필(Sung Pil Ma),정욱철(Wukchul Joung),이진호(Jinho Lee) 대한기계학회 2011 대한기계학회 춘추학술대회 Vol.2011 No.10
Loop heat pipe (LHP) is a two-phase heat transfer device of which working fluid circulating naturally along the loop with excellent heat transport capability. To start up this device, saturation pressure difference is required that occurs by generation of saturation temperature difference between evaporator and compensation chamber. With low heat load, saturation temperature difference is not enough to generate working fluid circulation, thus the LHP is not working properly. In this paper, heat sink is attached at the compensation chamber to reduce its temperature, thus increasing the saturation temperature difference at low heat load. Experimental results show the effect of compensation chamber cooling on LHP operation characteristics.
단일 평판형 증발면을 가지는 루프 히트 파이프의 운전특성
박광민(Kwang Min Park),마성필(Sung Pil Ma),이진호(Jinho Lee) 대한기계학회 2010 대한기계학회 춘추학술대회 Vol.2010 No.11
본 연구에서는 단일 평판형 증발면을 가지는 루프 히트 파이프의 운전특성에 대하여 실험적으로 조사하였다. 이를 위해 평판형 증발면을 가지는 루프 히트 파이프를 직접 제작하였다. 운전특성을 알아보기 위해 열 유입량 범위는 30W에서부터 70W 까지 10W 씩 변화시켰다. 30W에서는 작동유체가 순환하지만 정상상태의 물리적 현상에 도달하지 못하였으며, 40W~70W 까진 정상상태구간을 확인할 수 있었다. 열 유입량이 증가함에 따라 stage1, stage2 구간의 시간이 단축되는 것을 알 수 있었으며 열 유입량이 증가할 수록 열저항이 감소하는 것을 관찰할 수 있었다. This study deals with the operating characteristics of a loop heat pipe with single flat evaporator for heat load from 30W to 70W. The size of evaporator was 56.4×66.4×10㎜(W×H×D), double-pipe type condenser adopted was 1/4inch×600m(D×L). For heat load of 30W, though the system started with working fluid circulation, it did not reach at steady-state. For heat load from 40W to 70W, steady-state operation was obtained. Time period of stage 1, stage 2 and thermal resistance were reduced with increasing heat loads. For heat load exceeding 70W, the experiment was stopped due to pressure limit.
평판형 증발면을 가지는 루프 히트 파이프의 열 유입량에 따른 초기구동 특성
박광민(Kwang Min Park),마성필(Sung Pil Ma),이진호(Jinho Lee) 대한기계학회 2010 대한기계학회 춘추학술대회 Vol.2010 No.5
본 연구에서는 평판형 증발면을 가지는 루프 히트 파이프의 열 유입량에 따른 초기 작동특성에 대하여 연구하였다. 이를 위해 평판형 증발면을 가지는 루프 히트 파이프를 직접 제작하였으며 증발기 크기는 56.4×66.4×10㎜(W×L×H), 2 중관 구조의 응축기 외경 및 길이는 1/4inch×600m(D×L)이다. 초기 열 유입량은 작동유체가 순환하기 시작하는 30W에서부터 70W까지 변화시켰다. 초기 30W에서는 작동 유체가 순환하지만 정상적인 순환이 이루어지지 않았으며, 40W~60W까진 열 유입량이 증가함에 따라 정상적인 작동유체 순환시간이 짧아지는 것을 알 수 있었다. 70W 입력 시 허용 압력한계를 벗어나서 실험을 중단하였다. This study deals with the start-up characteristics of a loop heat pipe with flat evaporator for varying heat load from 30W to 70W. The size of evaporator was 56.4×66.4×10㎜(W×H×D), double-pipe type condense was 1/4inch×600m(D×L). For 30W heat load, the system started with working fluid circulated, but it was not normal circulation. For heat load from 40W to 60W, the start-up was normal and the start-up process time was reduced with increasing heat loads. For 70W heat load, the experiment was stopped due to pressure limits.