http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
자동차용 강판의 MAG 용접시 최적용접조건 선정에 관한 연구
방한서,방희선,주성민,노찬승,성보람,석한길,Bang, Han-Sur,Bang, Hee-Seon,Joo, Sung-Min,Ro, Chan-Seung,Sung, Bo-Ram,Suk, Han-Gil 대한용접접합학회 2009 대한용접·접합학회지 Vol.27 No.3
The optimization of the welding parameters was studied to maximize the weldability and minimize the amount of spatter in the MAG welding of automotive steel sheets under different shielding gas composition ratio. JS-EFSC, JS-SPHC steel plates and Ar mixture gases were used as a substrate and shielding gas for welding respectively. The five welding parameters were selected through preliminary experiments and their effects on the weldability were analyzed. Experiments were performed using the Taguchi experimental method. As results, appropriate range for welding could be achieved. Amount of spatter in 80%Ar+20%$CO_2$ shielding gas was 20% of that of $CO_2$welding. Therefore, in terms of high productivity and welding cost, Ar mixture gas(80%Ar+20%$CO_2$) was recommended as a shielding gas for application of MAG process, indicating the low spatter and good weld quality.
T-joint 용접부의 형상에 따른 역학적 메카니즘에 관한 연구
방한서,김종명 대한용접접합학회 1999 대한용접·접합학회지 Vol.17 No.6
The use of thick plate in increasing in recent years due to the rapid expansion of chemical plants, nuclear plants, ships and other industrial plants. Welding is the most popular joining techniques employed in manufacturing industrial machineries and structures. Normally, Groove shapes are prepared according to appropriate rules and regulations such as KS, JIS, AWS, LR, DNV and etc. for various thicknesses of plate. However those groove angles tend to be too large. As a result of large groove angle, residual stress, deformation of material and strength reduction is obtained. Therefore, the reliability and safety of structures and machinery tend to be decreasing. Therefore, in this paper, theoretical as well as experimental study are carried out to find optimum groove shapes for T-welded joint of mild steel. The test specimen are made in same condition with simulation model. Welding residual stresses measurement by sectional cutting method. ⅰ) The mechanical difference for change the thickness of plate and groove angle are not appeared. ⅱ) In a mechanical point of view minimum preparation angle(40°) is more suitable than maximum groove angle(60℃). ⅲ) The measurement value and distribution of welding residual stresses are not effected largely by groove angle. It is mechanical restraint that mainly affect welding residual stresses distribution. In mechanical point of view minimum groove angle is more suitable than maximum groove angle. Therefore, it is appropriate to minimize the size of groove shape in strength and safety.
방한서,강성원 대한용접접합학회 1997 대한용접·접합학회지 Vol.15 No.4
Welding is one of the most important and popular joining techniques employed in structures. In spite of, weld designs depend on the rules and regulations. Moreover, the study to optimize a shape of welding joint not may be sufficient and systematic on the theoretical and experimental sides. Therefore, in this study, a computer program based on thermal elasto plastic theory is developed for optimizing(minimizing) shape of weld joints. By the results, study is made on the characteristics of the distributions of welding residual stresses and plastic strains, and their production mechanisms. Also, Various kinds of tests are carried out to find out mechanical characteristics due to shape of weld joints. As a result of this optimization(minimization) of weld joints, the productivity and the reliability will be improved.
후판 용접부의 역학적 특성 -유한요소법에 의한 3차원 열탄소성 해석-
방한서 대한용접접합학회 1992 대한용접·접합학회지 Vol.10 No.4
In order to clarify the mechanical behavior of welding crack and to evaluate the mechanical characteristics of welded parts in thick plate, it is very important to accurately predict the welding deformation and residual stress including transient state before welding. In this paper, the theory of a three-dimensional elasto-plastic problem for the analysis of mechanical phenomenon of welding joint on the plate is developed into an efficient and accurate method based on the finite element method, and then several examples are considered by using the proposed model. The results of numerical analyses are discussed in the viewpoint of the mechanical characteristics of the distribution of three-dimensional welding residual stresses, plastic strains and their production mechanism on the thick plate.
방한서,방희선 대한용접접합학회 2001 대한용접·접합학회지 Vol.19 No.5
In order to classify the mechanical phenomena of thermal elasto-plastic behavior on the multi-spot welded joints, this study has tried to carry out three-dimensional thermal elasto-plastic analysis on them. However, because the shape of multi-spot welded joints is not taxi-symmetric, unlike the cafe of single-spot welded joint, the solution domain for simulation should be three dimension. Therefore, in this paper, firstly, the three-dimensional thermal elasto-plastic program is developed by an iso-parametric finite element method. Secondly, from the results analyzed by developed program, this has clarified mechanical characteristics and their production mechanism on single and multi-spot waled joints. Moreover, it has been intended to make clear effects of pitch length on welding residual stresses, plastic strain of multi-spot welded joints.
방한서,윤병현,김성주,임채환 대한용접접합학회 2003 대한용접·접합학회지 Vol.21 No.3
This paper describes the heat distribution characteristics of ASTM A131DH36 high tensile steel for ship structures in 5㎾ $CO_2$ laser welding. In general, high energy of laser beam concentrates on the small area of the weldment instantaneously; therefore, this heat transfer mechanism induces the rapid changes of temperature and mechanical characteristics in laser welds this mechanism. So temperature distribution analysis is important to understand mechanical characteristics of laser welds. Authors have conducted finite element simulation to analyze the heat distribution characteristics in laser welds. The result of simulation has been verified by comparing with the metallurgical experiment result. From the result of this study, we can accurately predict the heat distribution characteristics in laser welds by using numerical simulation.
조선용 후판 AH32 강에 대한 SAW 및 Hybrid(CO<sub>2</sub> Laser+MIG) 맞대기 용접부의 열 및 역학적 특성 비교
방한서,오종인,방희선,노찬승,이윤기,봉현수,이정수,Bang, Han-Sur,Oh, Chong-In,Bang, Hee-Seon,Ro, Chan-Seung,Lee, Yoon-Ki,Bong, Hyun-Soo,Lee, Jeong-Soo 대한용접접합학회 2008 대한용접·접합학회지 Vol.26 No.5
In this paper concentrate on the comparison of the thermal and mechanical characteristics in Butt joint of ship structure AH32 steel by using hybrid welding and conventional SAW. For this purpose, fundamental welding phenomena of hybrid process using $CO_2$ Laser and MIG is investigated by the experiments and characteristics of thermal and welding residual stress distribution of welded joint in SAW and hybrid welding are understood from the result of FE numerical simulation and experimental values. From the result of this study, it is understood that Laser-MIG hybrid welding have high potential, make substantial saving of time and manufacturing cost and may proves its self robust in the butt joining of thick AH32 steel ship structural plate in the near future.
溶接이음부 形狀變化에 따른 後熱處理時의 力學的 特性에 關한 硏究
방한서,강성원,김기성,김종명,노찬승 대한용접접합학회 1997 대한용접·접합학회지 Vol.15 No.2
In order to define the effects on shapes of welding joint, during Post Welding Heat Treatment (PWHT), we have carried out numerical analysis on the several test pieces by using computer program which was based on thermal-elasto-plastic-creep theories for the study. And then, welding residual stresses after PWHT were measured same test-pieces to compare with the results of numerical analysis. The main results obtained from this study is as follows: 1) The distribution modes of welding residual stresses are same on the all test pieces after and during PWHT by the both sides (measurement and numerical analysis). 2) The mechanical difference for change the thickness of plate and bevel angle are not appeared. 3) In a mechanical point of view (like material quality test, welding deformation etc.), manimum bevel angle (40$^{\circ}$.) is more suitable than maximum bevel angle (70$^{\circ}$).
厚板熔接部의 應力除去 熱處理時의 力學的 擧動에 關한 硏究
방한서 대한용접접합학회 1993 대한용접·접합학회지 Vol.11 No.4
Recently, several high-tensile steels(e.g. 80kg and above, $2^{1/4}Cr$-1Mo)having good quality to high temperature and pressure-resistance are widely used to construct petroleum-plant and pressure vessel of heat or nuclear-power plant. However, in the steels, reheating crack at grain boundaries of the heat affected zone(HAZ) occures during post welding heat treatment(PWHT)to remove welding residual stress. In order to study theoretically the characteristics of reheating crack created by PWHT, the computer program of three-dimensional thermal-elasto-plasto-creep analysis based on finite element method are developed, and then the mechanical behavior(history of creep strain accumulation and stress relaxation, etc)of welded join in thick plate during PWTH is clarified by the numerical results.