동일한 시료에 대한 국내 기관간의 STR 분석결과 비교 : STR 유전자좌 분석법의 표준화 설정을 위하여

박종태,신경진,양윤석,우광만,이숭덕,이승환,이정빈,정연보,조승희,한길로,한면수,홍승범 大韓法醫學會 2001 대한법의학회지 Vol.25 No.1

This paper described a collaborative exercise intended to see what kinds of short tandem repeat (STR) loci are used in different DNA typing laboratories in Korea and to compare their results for the demonstration whether uniformity of DNA profiling results from different laboratory could be achieved in Korea Laboratories were asked to test five tissue DNAs using methods routinely used in each laboratory and to report the results to the coordinating laboratory. The exercise demonstrated that each laboratory was using different STR loci for the typing with different STR numbers,2 VNTRS,36 STRs and amelogenin in total, and the direct comparison of the results from all the laboratory for the 18 loci could not be done as only one laboratory submitted typing results. Among 21 loci for which several laboratories submitted typing results, results for 14 loci were the same and results for the other 7 loci were different depending on the participating laboratory. D1S80, F13A01, D16S539, D21S11, D18S51, D3S1744 were the loci with different typing results. Even in the cases where commercial kits were used, the results were not the same depending on the machines used, that is the capillary electrophoresis or the gel based electrophoresis. The reason for the different results, points about the standardization of the methods arid the profiling data were described.

다발성 동맥류와 혈전증을 동반한 베체트병 1예

신표진,김장영,이승환,윤정한 대한순환기학회 1998 Korean Circulation Journal Vol.28 No.8

천정 크레인 시스템의 위치제어와 진동저감에 관한 연구

신승권,이한석,조영호,안두수 成均館大學校 科學技術硏究所 1998 論文集 Vol.49 No.1

Overhead crane systems are widely used for material transportation in many industrial fields. However, undesired swing can always be found during the moving progress, especially at the end location of the transport. The swing may increase the carrying time and cause safety problems. In order to achieve the target position, this paper used a PD controller and used a fuzzy controller to reduce swing angles found during the moving progress. The performance of controller was verified through the experimental results and the simulation results by MATLAB.

운동실조를 동반하지 않은 급성외안근마비 1례

신대수,이승회,이한샘,박성욱,박현영,장혁,김요식,조광호 圓光大學校 醫科學硏究所 2004 圓光醫科學 Vol.19 No.2

가변 광도에 따른 복합레진의 기계적 물성 및 변연누출도 변화

한승렬,민경산,신동훈 大韓齒科保存學會 2003 Restorative Dentistry & Endodontics Vol.28 No.2

Mechanical properties and microleakage of two composites [conventional hybrid type DenFil (VERICOM Co., Anyang, Korea) / micro matrix hybrid type Esthet X (Dentsply Caulk, Milford, DE, U.S.A.)] were evaluated to assess whether variable light intensity curing is better than conventional curing technique. Curing was done for 40 seconds in two ways of 2 step soft-start technique and 5 step ramping technique. Three kinds of light intensities of 50, 100, 200 mW/cm^2 were initially used for 10, 20, 30 seconds each and the maximum intensity of 600 mW/cm^2 was used for the rest of curing time in a soft-start curing technique. In a ramping technique, curing was done with the same initial intensities and the light intensity was increased 5 times with the same rate to the maximum intensity of 600mW/cm^2. After determining conditions that showed no different mechanical properties with conventional technique, Esthet X composite was filled in a class V cavity, which dimension was 4×3×1.5 mm and cured under those conditions. Microleakage was evaluated in two ways of dye penetration and maximum gap estimation through SEM observation. ANOVA and Spearman's rho test were used to confirm any statistical significance among groups. The results were as follows: 1. Several curing conditions of variable light intensities resulted in the similar mechanical properties with a conventional continuous curing technique, except conditions that start curing with an initial light intensity of 50 mW/cm^2, 2. Conventional and ramping techniques were better than soft-start technique in mechanical properties of microhardness and compressive strength. 3. Soft-start group that started curing with an initial light intensity of 100 mW/cm^2 for 10 seconds showed the least dye penetration. Soft-start group that started curing with an initial light intensity of 200 mW/cm^2 for 10 seconds showed the smallest marginal gap, if there was no difference among groups. 4. Soft-start technique resulted in better dye-proof margin than conventional technique(p=0.014) and ramping technique(p=0.002). 5. There was a very low relationship(p=0.157) between the methods of dye penetration and marginal gap determination through SEM evaluation. From the results of this study, it was revealed that ramping technique would be better than conventional technique in mechanical properties, however, soft-start technique might be better than conventional one in microleakage. It was concluded that much endeavor should be made to find out the curing conditions, which have advantages of both aspects or to solve these kinds of problems through a novel idea of polymerization.

A Digital Watermark

신정화,김인택,한승수 명지대학교 산업기술연구소 2001 産業技術硏究所論文集 Vol.20 No.-

In this paper, watermark technique has been proposed as a method to hide secret information into the signals so as to discourage unauthorized copying or attest the origin of the media. We present an approach for still image watermarking in which the watermark is embedded in the middle frequence area. It is confirmed from numerical experiments that the proposed method yields the watermarked image which is robust to several attacks.

일과성 전 기억상실증으로 나타난 크로이츠펠트 : 야콥병 1례

신대수,이승희,이한샘,박성욱,박현영,장혁,장성조,김요식,조광호 圓光大學校 醫科學硏究所 2004 圓光醫科學 Vol.19 No.1

다구치법에 의한 고 규소 내산주철의 용해주조공정 최적화

신제식,이상목,문병문,김정철,한동운,백승한 대한금속재료학회 2005 대한금속·재료학회지 Vol.43 No.2

In this study, Taguchi method, one of the design tools of experiments, was applied to optimize casting process parameters of the high silicon corrosion-resistant iron. Three casting process parameters such as melting temperature, rare earth metal (mischmetal) addition, and pouring temperature were chosen. Using SN (signal-to-noise) ratio calculated from ultimate tensile strength of each experimental casting run, the relationship between the casting parameters and mechanical properties was statistically evaluated. The casting condition of a melting temperature of 1,650℃, 0.2% rare earth metal addition, and a pouring temperature of 1,350℃ led to an excellent ultimate tensile strength above 11 kgf/mm², which is beyond the industrial criterion. The effects of the casting parameters on mechanical properties and corrosion resistance were further confirmed by combined analysis of fractography, hydrogen content determination, microscopic test, and acid resistance test. (Received August 23, 2004)

GT rotary file을 이용한 만곡 근관형성시 작업 효율 및 file 변형 발생에 관한 연구

신주희,백승호,배광식,임성삼,윤수한,김병현 대한치과보존학회 2001 Restorative Dentistry & Endodontics Vol.26 No.5

Root canal preparation process is of utmost importance in successful treatment of root canal. Also, one of the most important purpose of the root canal preparation is to enlarge the root canal three dimensionally without changing the curvature of the root canal. However, as the curvature of the root canal increases, there are many difficulties involved in formation of optimum root canal. Therefore, in order to solve the above mentioned problems, new developments in methods of root canal preparation and equipments for such purposes were made. Recently, vigorous studies about newly introduced engine-driven nitckel-ti-tanium rotary file are conducted. As shown in research results to dates, it is well established that the use of nickel-titanium file is better suited for curved root canal than stainless steel file in maintaining the curvature of root canal and reducing the deformation of root canal. However, it is also acknowledged that there are a few discrepancies in research results according to protocol, due to failure to remove variables in experiments. In addition, although it is recommended by the manufacturer that the GT rotary file should maintain a low rotational speed of 150∼350rpm and 'light pressure' as light as not to break the lead of a pencil, academic studies about the vertical force which is not yet standardized are not sufficiently explored. Therefore, this research devised and utilized a special research equipment to standardize the appropriate range of vertical force for GT rotary file through experiments by breaking of the lead of a pencil as expressed by the manufacturer and to accurately measure factors involved through repeating and recreating the environment of root canal preparation. Forming nine experimental groups by varying the vertical forces (150g, 220g, 300g) and rpm (150rpm, 250rpm, 350rpm), the effects of changing vertical forces and rpm on working efficiency were measured in terms of time expended in root canal preparation by crown-down method using a transparent resin block with 35 degree curvature and GT rotary file (z-test). The following research using this special research equipment that involved nine experimental groups and varying the vertical force for root canal preparation from 300g which is within the normal vertical force range to 700g and 1000g which fall outside the normal rpm range. The results were as follows : 1.Analysis of the experiment results revealed that the tome spent in root canal preparation decreased as the vertical forces and rpm increased (p<0.05). Also, the effects of rpm were greater than those of the vertical forces within the normal vertical force range (β-weight test) . 2.Observation of the deformation of GT rotary file revealed that deformation increases in a direct correlation with the vertical force increase and in a reverse correlation with the rpm decrease, In the case of the vertical forces close to the normal range, the probability of GT rotary file deformation were quite different depending on the rpm changes. In the case of◎eater tier◎cal forces, the occurrences of deformation of the file were more frequent regardless of the rpm changes. 3.Deformation and breakage of file were also commonly observed in the expended time measurement experiments and GT rotary file deformation experiments in which low speed rpm (150rpm) was used and at the curved portion of the resin block. Key words : GT rotary file, Crown-down method, Working efficiency, Vertical force, Rpm, Deformation and breakage of file

유리폐기물과 하수슬러지 소각재의 고형화 처리연구

한상목,신대용,윤봉구,김승겸 강원대학교 부설 석재복합신소재 제품연구센터 2002 석재연 논문집 Vol.7 No.-

하수슬러지 소각재, 폐유리분말 및 고로슬래그의 고형화에 의하여 건자재를 제조하였다. 하수슬러지 소각재는 SiO_2와 Al_2O_3가 75 wt%, Fe_2O_3가 8.21 wt%, 폐유리분말은 SiO_2 71.4 wt%, Na_2O 14.43 wt% 및 CaO 9.32 wt%, 고로슬래그는 SiO_2 33.4 wt%, CaO 41 wt% 및 Al_2O_3 14.5 wt%를 함유하여 세라믹스 제조원료로 사용이 가능하였다. 하수슬러지를 800℃에서 2시간 하소한 무기질분말을 분쇄하여 하수슬러지 소각재를 제조하였다. 30∼70 wt%의 하수슬러지 소각재, 30∼70 wt%의 폐유리분말 및 10∼30 wt%의 고로슬래그를 혼함하여 950∼1,100℃에서 2시간 소성하여 시편을 제조하였다. 하수슬러지 소각재 첨가량이 감소하고 폐유리분말의 첨가량과 소성온도가 증가하면 부피비중과 압축강도는 증가하였으나 기공률과 흡수율은 감소하였다. 1,050℃에서 소성한 시편(No. 1, 3, 5 및 7)의 부피비중은 1.70∼1.83, 기공률과 흡수율은 0.3∼2.4% 및 0.1∼1.5%, 압축강도 272∼323 kgf/㎠을 나타내었다. 고로슬래그를 첨가하여 1,100℃로 소성한 시편(No. 8, 9, 및 10)의 부피비중은 1.82∼2.11 및 압축강도는 350∼671 kgf/㎠이었다. 하수슬러지 소각재, 고로슬래그 및 시편의 중금속출량은 매립지 침출수배출 허용기준치보다 낮아, 본 연구에서 제조한 시편은 주변 환경에 해가 없어 건자재로의 이용이 가능하였다. An experimental study for the constructional material by solidification using sewage sludge ash, waste glass powder and blast furnace slag was carried out in the senses of waste materials disposal and utilization. The reusability of sewage sludge ash, waste glass powder and blast furnace slag as a raw material in the manufacturing process of ceramics was highly expected because the chemical compositions of these waste materials were mostly SiO_2 and Al_2O_3. Sewage sludge ash was fabricated by calcined at 800℃ for 2 hours and obtained by the crushing. The mixture of 30∼70wt% of sewage sludge ash, 30∼70 wt% of waste glass powder and 10∼30 wt% of blast furnace slag were heated at 950∼1,100℃ for 2 hours. The density and the compressive strength of specimen increased with increasing the sintering temperature and decreasing the addition amount of sewage sludge ash, No. 1, 3, 5 and 7 specimens showed the bulk density of 1.70∼1.83, porosity of 0.3∼2.4%, water absorption of 0.1∼1.5% and compressive strength of 272∼323kgf/㎠. And, that of the No. 7 specimen heated at 1,100℃ increased with increasing the addition amount of blast furnace slag, and for No. 8, 9 and 10 specimens, bulk density was 1.82∼2.11 and compressive strength was 350∼671 kgf/㎠. An extraction test for specimen to detect toxic materials showed below the permitted standard of land-filling extractable heavy metal contents. It was founded that the specimen were useful for the constructional materials.