http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
Maengkyo Oh,Keunyoung Lee,Ba Ro Lee,Kyu Tae Park,Hyun Young Shin 한국방사성폐기물학회 2023 한국방사성폐기물학회 학술논문요약집 Vol.21 No.2
Decommissioning waste is generated with various types and large quantities within a short period. Concrete, a significant building material for nuclear facilities, is one of the largest decommissioning wastes, which is mixed with aggregate, sand, and cement with water by the relevant mixing ratio. Recently, the proposed treatment method for volume reduction of radioactive concrete waste was proven up to scale-up testing using unit equipment, which involved sequentially thermomechanical and chemical treatment. According to studies, the aggregate as non-radioactive material is separated from cement components with contaminated radionuclides as less than clearance criteria, so the volume of radioactive concrete waste is decreased effectively. However, some supplementation points were presented to commercialize the process. Hence, the process requires efficiency as possible to minimize the interface parts, either by integration or rearranging the equipment. In this study, feasibility testing was performed using integrated heating and grinding equipment, to supplement the possible issue of generated powder and dust during the process. Previously, heat treatment and grinding devices were configured separately for pilot-scale testing. But some problems such as leakage and pipe blockage occurred during the transportation of generated fine powder, which caused difficulties in maintaining the equipment. For that reason, we studied to reduce the interface between the equipment by integrating and rearranging the equipment. To evaluate the thermal grinding performance, the fraction of coarse and concrete fines based on 1mm particle size was measured, and the amount of residual cement in each part was analyzed by wet analysis using 4M hydrochloric acid. The result was compared with previous studies and the thermomechanical equipment could be selected to enhance the process. Therefore, it is expected that the equipment for commercialization could be optimized and composed the process compactly by this study.
Maengkyo Oh,Keunyoung Lee,Min-Ku Jeon,Richard Ian Foster,Chang-Ha Lee 한국방사성폐기물학회 2022 한국방사성폐기물학회 학술논문요약집 Vol.20 No.2
Decommissioning waste is generated at all stages during the decommissioning of nuclear facilities, and various types of radioactive waste are generated in large quantities within a short period. Concrete is a major building material for nuclear facilities. It is mixed with aggregate, sand, and cement with water by the relevant mixing ratio and dried for a certain period. Currently, the proposed treatment method for volume reduction of radioactive concrete waste was involved thermomechanical and chemical treatment sequentially. The aggregate as non-radioactive materials is separated from cement components as contaminated sources of radionuclides. However, to commercialize the process established in the laboratory, it is necessary to evaluate the scale-up potential by using the unit equipment. In this study, bench-scale testing was performed to evaluate the scale-up properties of the thermomechanical and chemical treatment process, which consisted of three stages (1: Thermomechanical treatment, 2: Chemical treatment, 3: Wastewater treatment). In the first stage, lab, bench, and pilot scale thermomechanical tests were performed to evaluate the treated coarse aggregate and fines. In the second stage, the fine particles generated by the thermomechanical treatment process, were chemically treated using dissolution equipment, after then the removal efficiency and residual of cement in the small aggregate was compared with laboratory results. The final stage, the secondary wastewater containing contaminant nuclides was treated, and the contaminant nuclides could be removed by chemical precipitation method in the scale-up reactors. Furthermore, an additional study was required on the solid-liquid separation, which connected each part of the equipment. It was conducted to optimize the separation method for the characteristics of the particles to be separated and the purpose of separation. Therefore, it is expected that the basic engineering data for commercialization was collected by this study.
Study on Thermal Decomposition Characteristics of Dry Active Wastes From the Nuclear Facilities
Maengkyo Oh,Min Ku Jeon,Sung-Wook Kim,Hee-Chul Yang,Keunyoung Lee 한국방사성폐기물학회 2023 한국방사성폐기물학회 학술논문요약집 Vol.21 No.1
Dry active wastes (DAWs) are a type of combustible radioactive solid waste, which includes decontamination paper, protective clothing, filters, plastic bags, etc. generated from operating nuclear facilities and decommissioning projects. The volume of DAWs could be increased over time, disadvantage to higher disposal costs and space utilitization of disposal site. Additionally, incineration methods cannot be applied to DAWs, unlike general environmental waste, due to concerns about air pollution and the release of harmful chemicals with radioactive nuclides into the atmosphere. Recently, KAERI developed an alternative thermochemical process for reducing the volume of DAW, which involves a step-wise approach, including carbonization, chlorination, and solidification. The purpose of this process is to selectively separate the radioactive nuclides from carbonized DAWs that are less than clearance criteria, which can be disposed of as non-radioactive waste. In this research, we investigated the thermal decomposition characteristics of DAWs using nonisothermal thermogravimetric analysis, which was performed with different categorized wastes and heating conditions. As a result, the cellulose DAWs such as decontamination paper and cotton were thermally decomposed in three or four-step depending on the heating conditions. On the other hand, the hydrocarbon and rubber DAWs such as plastic bags and latex were thermally decomposed in one or two-step. Therefore, it could be suggested the thermochemical treatment conditions that minimize the decomposition of DAWs by controlling the reaction steps, and we will try to apply these results for cellulose type DAWs such as decontamination paper and cotton, which is generated majorly from the nuclear facilities in the future.
Evaluation of Chemical Precipitation for 137Cs and 90Sr Separation From Complexed Acidic Wastewater
Maengkyo Oh,Keunyoung Lee,Richard I. Foster,Chang-Ha Lee 한국방사성폐기물학회 2022 한국방사성폐기물학회 학술논문요약집 Vol.20 No.1
Concrete is one of the largest wastes, by volume, generated during the decommissioning of nuclear facilities, which significantly influences the projected costs for the disposal of decommissioning wastes. Concrete consists of aggregates and a cement binder. In radioactive concrete, the radioisotopes are mainly associated with the cement component. If the radioactive isotope can be separated from the concrete to below the clearance criteria, the volume of radioactive concrete waste could be reduced effectively. We were studied to separate the radioactive materials from the concrete by using the thermomechanical and chemical treatment processes, sequentially. From the study, separated aggregate could be treated to achieve the clearance level. However, these processes generate a large volume of secondary acidic radioactive wastewater, which might be a critical problem to reduce the volume of radioactive concrete waste. In this research, separating the 137Cs and 90Sr from dissolved concrete wastewater to below the discharge criteria by precipitation method, it would be released to the environment under industrial waste guidelines. The experiments were conducted to using a simulated radioactive wastewater, formed by the dissolution of concrete within HCl, which was spiking the 137Cs and 90Sr, respectively. In addition, we applied the chemical precipitation methods with wastewater, using ferrocyanide for 137Cs and BaSO4 coprecipitation for 90Sr. As a result, targeted radionuclides could be removed to the discharge level (137Cs: 0.05 Bq·ml?1, 90Sr: 0.02 Bq·ml?1) by precipitation method. Therefore, it could reduce the secondary wastewater effectively by precipitation method and enhance the additional volume reduction for radioactive concrete waste.
Keunyoung Lee,Maengkyo Oh,Richard I. Foster,Kwang-Wook Kim,Sungjune Sohn,Min Ku Jeon,Bum-Kyoung Seo 한국방사성폐기물학회 2022 한국방사성폐기물학회 학술논문요약집 Vol.20 No.2
Radioactive waste generated in large quantities from NPP decommissioning has various physicochemical and radiological characteristics, and therefore treatment technologies suitable for those characteristics should be developed. Radioactively contaminated concrete waste is one of major decommissioning wastes. The disposal cost of radioactive concrete waste is considerable portion for the total budget of NPP decommissioning. In this study, we developed an integrated technology with thermomechanical and chemical methods for volume reduction of concrete waste and stabilization of secondary waste. The unit devices for the treatment process were also studied at bench-scale tests. The volume of radioactive concrete waste was effectively reduced by separating clean aggregate from the concrete. The separated aggregate satisfied the clearance criteria in the test using radionuclides. The treatment of secondary waste from the chemical separation step was optimally designed, and the stabilization method was found for the waste form to meet the final disposal criteria in the repository site. The final volume reduction rates of 56.4~75.4% were possible according to the application scenario of our processes under simulated conditions. The commercial-scale system designs for the thermomechanical and chemical processes were completed. Also, it was found that the disposal cost for the contaminated concrete waste at domestic NPP could be reduced by more than 20 billion won per each unit. Therefore, it is expected that the application of this technology will improve the utilization of the radioactive waste disposal space and significantly reduce the waste disposal cost.