http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
개별검색 DB통합검색이 안되는 DB는 DB아이콘을 클릭하여 이용하실 수 있습니다.
통계정보 및 조사
예술 / 패션
<해외전자자료 이용권한 안내>
- 이용 대상 : RISS의 모든 해외전자자료는 교수, 강사, 대학(원)생, 연구원, 대학직원에 한하여(로그인 필수) 이용 가능
- 구독대학 소속 이용자: RISS 해외전자자료 통합검색 및 등록된 대학IP 대역 내에서 24시간 무료 이용
- 미구독대학 소속 이용자: RISS 해외전자자료 통합검색을 통한 오후 4시~익일 오전 9시 무료 이용
※ 단, EBSCO ASC/BSC(오후 5시~익일 오전 9시 무료 이용)
After drilling operations at the offshore plant to production to crude oil to high pressure. After that time the low pressured of pipe inside when the secondary produce so oil recovery is reduced. At that time injection sea water at the pipe inside through water injection pump that the device Increase recovery so to be research and development at many industry. So developing 3-stage water injection pump at the domestic company. A variety of mathematical analysis during the detailed design analysis was not made through the dynamics characteristic. In this paper, a 2D finite element analysis is performed through the dynamics of the present study was the validation of the model.
After drilling operations at the offshore plant, crude oil is producted under high pressure. After that time, oil recovery is reduced, because the pressure of the pipe inside is low during the secondary produce. At that time injection sea water at the pipe inside through water injection pump that the device increase to recovery. A variety of mathematical analysis during the detailed design analysis was not made through the dynamics characteristic at the domestic company. 2D model has reliability of analysis results for the uncomplicated model. Also element and the node the number of significantly less than in the 3D model. So, the temporal part is very effective. In addition, depending on the quality of mesh 3D is a real model and FEM model occurs error. So, user needs a lot of skill. In this paper, a 2D finite element analysis was performed through the dynamics analysis and the study model was validated.
This paper provides how to solve the problems analytically and experimentally that occur for testing the water injection pump under development. First of all, water injection pump, based on shaft system dynamic analysis, is verified by measuring the behavior of the shaft system. After the water injection pump is measured, the structural resonances which can cause excessive noise, degradation the equipment life and malfunction are found. Therefore, by changing the structural design, the resonance should be avoided. Application of the design variables to the experimentally resonance avoidance is difficult. So analytically, with application of the design variables, the design will be changed with mode analysis using FEM.
This paper analyzes the pitting's cause of elevator's worm gear type traction machine. To find a cause of pitting problem, we analyzed vibration, a proper design allowance and lubrication. We brought a conclusion that the cause of pitting is not a simple vibration problem, such as misalignment of worm reducer and rail, but mostly related to a designed allowance. In this case, the allowance is tight. In general, the allowance of traction machine and lubrication is varied by manufacturers. When the allowance is tight, a proper lubrication can diminish the pitting problem.
Condition monitoring(CM) is a method based on non-destructive test(NDT). So, recently many kind of NDT were applied for CM. Acoustic emission(AE) is widely used for the early detection of faults in rotating machinery in these days because of high sensitivity than common accelerometers and detectable low energy vibration signals. And crack is considered one of severe fault in the rotating machine. Therefore, in this paper, study on early detection using AE has been accomplished for the crack of the low-speed shaft. There is a seeded initial crack on the shaft then the AE signal had been measured with low-speed rotation as the applied load condition. The signal detected from crack in rotating machine was detected by the AE transducer then the trend of crack growth had found out by using some of feature values such as peak value, skewness, kurtosis, crest factor, frequency center value(FC), variance frequency value(VF) and so on.