http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
개별검색 DB통합검색이 안되는 DB는 DB아이콘을 클릭하여 이용하실 수 있습니다.
통계정보 및 조사
예술 / 패션
<해외전자자료 이용권한 안내>
- 이용 대상 : RISS의 모든 해외전자자료는 교수, 강사, 대학(원)생, 연구원, 대학직원에 한하여(로그인 필수) 이용 가능
- 구독대학 소속 이용자: RISS 해외전자자료 통합검색 및 등록된 대학IP 대역 내에서 24시간 무료 이용
- 미구독대학 소속 이용자: RISS 해외전자자료 통합검색을 통한 오후 4시~익일 오전 9시 무료 이용
※ 단, EBSCO ASC/BSC(오후 5시~익일 오전 9시 무료 이용)
In this study, a ship motion control system design method is introduced for autonomous ships. Some related research results and technologies for autonomous ships have already been developed and applied to ships. For example, the Norwegian Maritime Authority and the Coastal Administration have signed an agreement that allows to test of autonomous ships in the defined area (port to port). Many countries and industries are pursuing to realize the autonomous vessel in the real world. In this paper, the authors try to develop related technology. As basic research, a ship model of the pilot vessel is developed and physical parameters are identified by experiment and simulations. Using the mathematical ship model, a control system is designed and control performance is evaluated by simulations.
In this study, a control system design method for realizing automatic ship berthing in the harbour area is considered. In general, the control system for berthing have been issued as a simple root tracking problem without complex harbour environment. The harbour is crowded with many ships such that the berthing root to the quay side is too complex and not easy to approach there. Therefore, in this study, the authors set the berthing root to two approaching modes which are defined as the ballistic and final phase. In the ballastic mode, the vessel moves using all actuators. And in the final mode, the vessel uses two side thrusters for keeping it in parallel moving. For obtaining good root tracking performance without tracking error in the steady state, a servo-system with an integrator is designed based on LMI approach. Simulation results using a vessel model are given such that the specified control performance is verified.
Diesel particulate filter has been adopted in new vehicle with diesel engine. Since the flow of exhaust gas was clogged as particulate matters were deposited in the filter, it have bad effects on a fuel consumption and power. It was investigated that a particulate filtering system with vacuum pump in the exhaust gas line could be free from clogging in previous research. In this study, the effects of water injection and position of inlet port in filtering system on reducing in particulate matter were investigated. It was noticed that particulate matter were decreased remarkable by water injection and moving the position of inlet port.
Over the past years, many research works have been carried out to investigate the factors which govern the performance of diesel engines. The air pollutant emissions from the diesel engines are still significant concerns environmentally in many countries. In the present study, a novel smoke filtration system of diesel engine is proposed. This novel system is composed of filtering elements and vacuum pump driven by exhaust gases emitted from engine cylinders for capturing smoke. In order to verify the excellency of the novel filtration system, the differential pressure across the filtration system is investigated experimentally comparing with other systems which are used commercially in diesel vehicles. As a result it is founded that the differential pressure of the novel system is the smallest among them.
As environmental pollution reduction devices were installed in diesel engines, a gas flow analysis of intake and exhaust systems is required. A gas flow analysis in 3D format needs a high-resolution workstation and enormous time for analysis. Therefore, the method of characteristics was used for a gas flow analysis with a fast calculation time and a low-resolution workstation. An experiment was conducted on single cylinder diesel engine to measure cylinder pressure and exhaust pipe pressure. In order to validate a gas flow analysis using the method of characteristics, the results analyzed under the same conditions as the experiment were compared. As the results of the analysis using the method of characteristics, the cylinder pressure showed accuracy; however, the exhaust pipe pressure was inaccurate. In the future, the shortcomings of the analysis using the method of characteristics will be supplemented by using the 1D-3D coupling method.
A demand for bio-diesel oil increases as one of solution for exhaustion of fossil fuel and reduction of CO2 emission, and research on bio-diesel is being carried out. Bio-diesel oil is mainly esterified from vegetable oil with methanol in order to use for fuel on diesel engine and has demerit that costs are increased as compared with directly using like non-esterified one. Bio-diesel oil within 3% mixed with gas oil is used at present, proportion of bio-diesel oil will be increase by 5% in future. We judged that wasted soybean oil non-esterified could be used on diesel engine with an electronic fuel injection according to previous researches with a mechanical fuel injection. A performance test using only gas oil, gas oil with esterified bio-diesel oil 5% and wasted soybean oil non-esterified 5% on diesel engine with the electronic fuel injection were carried out. It is noticed that gas oil with wasted soybean oil non-esterified 5% has more similar characteristics to gas oil than gas oil with esterified bio-diesel oil 5%.
Since bio-diesel oil has a merit that it satisfies both demand of substitution for fossil fuel and reduction in carbon dioxide emission, it is widely used in diesel engines by blending in gas oil in small quantity. It is needed to reduce in NOx emission in some way or others if blending ratio of bio-diesel oil is going to increase, because it is demerit that bio-diesel oil emits more NOx emission than gas oil. In this study, it was accomplished to optimize 3 factors what effect on NOx emission as blending ratio of bio-diesel oil, injection timing and common rail pressure with an introduction of a design of experiments, in order to minimize a number of tests. It was cleared that to introduce the design of experiments was very available in NOx optimization.