http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
권세원(S. W. Kwon),박용범(Y. B. Park),권신원(S. W. Kwon),권용무(Y. M. Kwon),김점식(J. S. Kim),송현석(H. S. Song),문성원(M. S. Mun),신운용(W. Y. Shin) 한국조명·전기설비학회 2006 한국조명·전기설비학회 학술대회논문집 Vol.2006 No.11월
기존의 인력굴착을 통한 지선근가 매설시공방법을 오거크레인에 의한 기계화시공을 하기 위하여 오거크레인 굴착공에 적합한 원형 지선근가를 개발을 하고 개발된 원형근가를 오거크레인을 이용한 기계화시공에 적용함으로써 공사시간 및 비용 절감과 시공품질의 향상을 이루려 한다.
신축형 오거크레인용 유압식 확장기를 이용한 아치형 전주근가 시공법
김점식(J. S. Kim),권세원(S. W. Kwon),박용범(Y. B. Park),권신원(S. W. Kwon),문성원(S. W. Mun),조성문(S. M. Cho),김도영(D. Y. Kim),권용무(Y. M. Kwon) 대한전기학회 2008 대한전기학회 학술대회 논문집 Vol.2008 No.4
현행 배전선로의 전주근가(1.2m 장방형)는 오거크레인을 이용한 건주공사 완료 후 전주근가 시공을 위한 별도의 인력 또는 백호우 장비가 추가로 투입되어 시공함으로써 인력으로는 공사시간이 장기간 소요되고 백호우 장비로는 작업장 환경훼손과 시공원가 상승의 문제점이 있었다. 이러한 문제점을 해소하기 위하여 건주공사에 사용되는 오거크레인의 굴착 직경을 80㎝까지 확장 가능한 ‘신축형 오거크레인용 유압식 확장기’와 원형 굴착공에 시공이 가능한 ‘아치형 전주근가’를 개발하고 이를 이용한 시공기술을 개발함으로써 동일장소에서 굴착작업이 수반되는 건 주작업, 전주근가 매설작업을 가능하게 하여 장비활용성 증대, 작업장 환경개선, 공사기간 단축 및 시공원가 절감 등의 효과가 기대되는 기술을 개발하였다.
백금 히터가 내장된 평면형 Bi - Sb 다중접합 열전변환기의 특성
이현철,김진섭,함성호,이종현,이정희,박세일,권성원 ( H . C . Lee,J . S . Kim,S . H . Ham,J . H . Lee,J . H . Lee,S . I . Park,S . W . Kwon ) 한국센서학회 1998 센서학회지 Vol.7 No.3
A planar Bi-Sb multijunction thermal converter with high thermal sensitivity and small ac-do transfer error has been fabricated by preparing the bifilar thin film Pt-heater and the hot junctions of thin film Bi-Sb thermopile on the Si₃N₄/SiO₂/Si₃N₄-diaphragm, which functions as a thermal isolation layer, and the cold junctions on the dielectric membrane supported with the Si-substrate, which acts as a heat sink, and its ac-do transfer characteristics were investigated with the fast reversed de method. The respective thermal sensitivities of the converter with single bifilar heater were about 10.1 mV/mW and 19.8 mV/mW in the air and vacuum, and those of the converter with dual bifilar heater were about 5.1 mV/mW and 7.fi mV/mW, and about 5.3 mV/mW and 7.8 mV/mW in the air and vacuum for the inputs of inside and outside heaters, indicating that the thermal sensitivities in the vacuum, where there is rarely thermal loss caused by gas, are higher than those in the air. The ac-do voltage and current transfer difference ranges of the converter with single bifilar heater were about ±1.80 ppm and ±0.58 ppm, and those of the converter with dual bifilar heater were about ±0.63 ppm and ±0.25 ppm, and about ±0.53 ppm and ±0.27 ppm, respectively, for the inputs of inside and outside heaters, in the frequency range below 10 kHz and in the air.
박영태,권성원,강전홍 ( Y . T . Park,S . W . Kwon,J . H . Gang ) 한국센서학회 1996 센서학회지 Vol.5 No.3
A L DT is an electromechanical transducer that produces an electrical output proportional to The displacement of separate movable core. A convential LDT in construction has a disadvantage which the measurement range to the length ratio is small. This paper proposed a new type LDT, which improved methodes of construction. The proposed LDT and a conventional LVDT with the same dimension are simulated by FE. In the process of the simulation and construction, the performance of two type LVDTs are evaluated. Linearity error of a conventional LVDT was ±3 % in measuring range of ±5 mm and linearity error of the proposed LVDT was ±0.5 % in the same range. It was evident from the theoritical relationships and the experimental results that the proposed LVDT has been better performance than a convential type.