플라즈마 CVD 법을 이용한 대면적 균일한 비정질 탄소 막 증착

윤상민,양성채,Yun, Sang-Min,Yang, Sung-Chae 한국전기전자재료학회 2009 전기전자재료학회논문지 Vol.22 No.5

It has been investigated for the film uniformity and deposition rate of a-C:H films on glass substrate and polymeric materials in the presence of the modulated crossed magnetic field. We used Plasma CVD, i.e, using a crossed electromagnetic field, for uniform depositing thin film. The optimum discharge condition has been discussed for the gas pressure, the magnetic flux density and the distance between substrate and electrodes, As a result, it is found that the optimum discharge conditions are $CH_4$ concentration $CH_4$=10 %, modulated magnetic flux density B=48 Gauss, pressure P=100 mTorr, discharge power supply voltage V=l kV under these experimental conditions. By using these experimental condition, it is possible to prepare the most uniform film extends over about 160 mm of the film width. In this study, we deposited a-C:H thin film on glass substrate, and have a plan that using this condition, study depositing a-C:H thin film on polymeric substrate in next studies.

플라즈마 표면처리를 이용한 YBCO Coated Conductor의 Ag 박막층 증착에 관한 연구

정현기,양성채,최병정,두호익,Jeong, Hyun-Gi,Yang, Sung-Chae,Choi, Byoung-Jung,Du, Ho-Ik 한국전기전자재료학회 2017 전기전자재료학회논문지 Vol.30 No.1

The Ag thin film of YBCO (yttrium barium copper oxide) CC (coated conductor) protect the YBCO layer and, at the same time, affects the electrical characteristics of the YBCO CC. Therefore, YBCO CC with the commercialization of the Ag thin film layers makes it easy to establish a process, it can lead to a variety of characteristic changes in YBCO CC. In this paper, plasma surface treatment was carried out to facilitate the deposition of the Ag thin film and the deposition process of YBCO CC. Surface roughness from the test results was increased as the time of the plasma surface treatment increased from 5 to 20 minutes. On the other hand, the surface roughness was decreased for the time of the plasma surface treatment over 20 minutes. Furthermore, after depositing, the increasing of deposit amount and reduced lifting phenomenon showed a similar tendency with the rise time of surface roughness.

저온프로세스를 이용한 고분자필름의 플라즈마 표면처리

조욱,양성채,Cho, Wook,Yang, Sung-Chae 한국전기전자재료학회 2008 전기전자재료학회논문지 Vol.21 No.5

The plasma processing is applied to many industrial fields as thin film deposition or surface treatment technique. In this study, we investigated large-area uniformed surface treatment of PET film at low temperature by using Scanning Plasma Method(SPM). Then, we measured difference and distribution of temperature on film's surface by setting up a thermometer. We studied the condition of plasma for surface treatment by examining intensity of irradiation of uniformed plasma. And we compared contact angles of treated PET film by using Ar and $O_2$ plasma based low temperature. In our result, surface temperature of 3-point of treating is low temperature about $22^{\circ}C$, in other hands, there is scarcely any variation of temperature on film's surface. And by using Ar plasma treatment, contact angle is lower than untreatment or $O_2$ plasma treatment. In case of PET film having thermal weak point, low temperature processing using SPM is undamaged method in film's surface and uniformly treated film's surface. As a result, Ar plasma surface treatment using SPM is suitable surface treatment method of PET film.

주사 플라즈마 법(SPM)을 이용한 소수성 표면처리

김영기,최병정,양성채,Kim, Young-Gi,Choi, Byoung-Jung,Yang, Sung-Chae 한국전기전자재료학회 2010 전기전자재료학회논문지 Vol.23 No.1

The plasma processing technologies of thin film deposition and surface treatment technique have been applied to many industrial fields. This study is purposed Large-area uniformity and surface treatment on the stainless substrate. We treat surface of stainless by $CF_4$ plasma. $CF_4$ plasma is generated by using SPM(Scanning plasma method)which is kind a of CVD. Generally, SPM has been used for uniform surface treatment using a crossed electromagnetic field. The optimum discharge condition has been studied for the gas pressure, the magnetic flux density and the distance between substrate and electrodes. In result, contact angle is increased by surface treatment using $CF_4$ Plasma. Therefore we expect that SPM to control contact angle is applied to many industries.

EBSD를 이용한 1, 2차 용융흔 결정립의 방위 비교 분석

박광묵,방선배,양성채,Park, Kwang-Muk,Bang, Sun-Bae,Yang, Sung-Chae 한국전기전자재료학회 2017 전기전자재료학회논문지 Vol.30 No.11

Herein, for the quantitative analysis of the arc beads related to electric fire, we used electron backscatter diffraction (EBSD), a measuring device for grain orientation of materials, we compared and analyzed the surface texture of primary and secondary beads according to the difference in cooling rate at ambient temperature. This analysis revealed that the primary beads showed similar distribution at both low and high angles, while the secondary beads showed a higher distribution at low angles than at high angles. Thus, EBSD can be used for quantitative analysis of the beads and can be applied to identify beads in the future.

차전류 차분 블로킹 변압기 보호용 전류차동 계전기

姜龍澈(Yong-Cheol Kang),元成浩(Sung-Ho Won),金大成(Dae-Sung Kim),楊城彩(Sung-Chae Yang) 대한전기학회 2003 전기학회논문지A Vol.52 No.12

제주재래흑돼지와 Landrace, 교배집단 F<SUB>2</SUB>에서 척추의 수적 변이와 도체형질의 상관관계

조인철(In-Cheol Cho),김상금(Sang-Keum Kim),김유경(Yoo-Kyung Kim),강용준(Yong-Jun Kang),양성년(Sung-Nyun Yang),박용상(Yong-Sang Park),조원모(Won-Mo Cho),조상래(Sang-Rae Cho),김남영(Nam-Young Kim),채현석(Hyun-Seok Chae),성필남(Pil-Nam 한국생명과학회 2013 생명과학회지 Vol.23 No.7

포유류 중 돼지의 척추 중 요추, 흉추의 수는 고정되지 않은 형질로 개체간의 차이를 나타내는 것으로 알려져 있다. 본 연구는 제주재래흑돼지와 Landrace, 두 품종 간 F₂ 교배집단에서 경추 수, 흉추 수, 요추 수, 척추 수 등 체형관련 형질과 도체형질의 상관관계를 살펴보기 위해 수행되었다. 세 축군 모두 경추 수의 변이는 나타나지 않았으나, 흉추 수, 요추 수, 척추 수는 상이한 양상을 보였다. 도체형질의 성적과 요추 수만이 세 축군들 사이에서 통계적인 유의성을 나타내지 않았고(p>0.05), 도체중, 육색, 근내지방도, 등심단면적, 등지방두께, 도체장, 흉추 수, 척추 수 등은 통계적인 유의성을 나타내었다(p<0.05). 제주재래흑돼지는 흉추 수 14-16 개, 요추 수 5-6 개, 척추 수 27-29 개의 범위, Landrace는 흉추 수 15-16 개, 요추 수 5-7 개, 전체 척추 수 28-29 개, F₂ 교배집단은 흉추 수 14-17, 요추 수 5-7 개, 전체 척추 수 27-30 개로 확인되었다. F₂ 교배집단에서 흉추 수와 척추 수의 증가는 도체중, 도체장, 등지방두께의 평균이 유의적으로 다른 양상을 보인다(p<0.05). 또한 척추 수의 증가는 요추 수의 증가보다 흉추 수의 증가에 더 많은 영향을 받는 것으로 나타났다. 흉추 수 및 척추 수의 증가가 등지방두께를 점점 두껍게 만들기는 하지만, 도체중과 도체장 등 경제성을 결정하는 핵심적인 도체형질을 향상시킨다는 점은 추후 제주재래흑돼지나 Landrace 품종을 활용한 양돈산업에서 체형개선을 통한 생산성 증가를 유발할 수 있는 좋은 전략이 될 것으로 판단된다. The number of thoracic and lumbar vertebrae is known to be an unfixed trait among mammals. This study focused on the relationship between numerical variations of cervical (CER), thoracic (THO), and lumbar (LUM) vertebrae and the total number of vertebrae (TNV) and carcass traits in Jejunative black pigs (JBPs), Landrace pigs, and their intercrossed F₂ population. There were no numerical variations in CER vertebrae. On the other hand, the numbers of THO and LUM vertebrae and the TNV varied in all three populations. Of the traits investigated in the three populations, only the means±SE of the LUM vertebrae did not show statistical significance (p>0.05). The carcass weights (CW), meat color (MC), marbling score (MS), backfat thickness (BFT), carcass length (CLE), THO vertebrae, and TNV all showed statistical significance (p<0.05). The JBP had 14-16 THO vertebrae, 5-6 LUM vertebrae, and 27-29 TNV. The Landrace pigs had 15-16 THO vertebrae, 5-7 LUM vertebrae, and 28-29 TNV. The F₂ population had 14-17 THO vertebrae, 5-7 LUM vertebrae, and 27-30 TNV. In the F₂ population, increased numbers of THO vertebrae and TNV were associated with a significant increase in the CW, CLE, and BFT (p<0.05). In particular, the increase in the TNV was caused by an increase in the number of THO rather than LUM vertebrae. Although the animals with a greater number of THO and TNV had thicker backfat, they had a longer CLE and a heavier CW. Both these traits are economically more important than the level of backfat when determining the productivity level. These results suggest that genetic selection to increase the number of vertebrae, especially in Landrace pigs, JBPs, and their related populations, may be an excellent strategy for improving productivity.

전력계통 운영조건을 고려한 발전기차단용 SPS 동작설정에 관한 연구

권한나(Gwon, Han Na),손혁진(Son, Hyeok-Jin),국경수(Kook, Kyung-Soo),양성채(Yang, Sung-Chae) 한국산학기술학회 2014 한국산학기술학회논문지 Vol.15 No.1

발전기차단용 고장파급방지장치(SPS; Special Protection Scheme)는 대규모 발전단지의 인출 송전선로 고장 시 발전단지 내의 발전기 과속을 방지하기 위해 사전에 계획된 대수만큼 해당 발전기를 즉시 차단하여 전력계통 전 체의 안정도를 유지하는 비상 장치이다. 그러나 기존의 국내 발전기차단용 SPS 동작은 첨두부하를 기준으로 산정된 값을 일률적으로 적용하여 운영 되고 있어 경부하시에 발전기차단용 SPS가 동작을 하게 되면 발전기 과차단으로 인 한 발전력 부족을 초래할 가능성이 있는 등 SPS 운영의 비효율성이 잠재되어있다. 이를 위해 본 논문에서는 수시로 변화하는 전력계통 운영조건을 주기적으로 취득하고 정확도와 속도가 우수한 COA기반의 안정도평가를 통해 발전기 차단용 SPS 동작을 설정함으로써 경부하시에는 SPS 발전기 탈락대수가 첨두수요 기준의 설정치보다 감소되어 계통 고장에 의한 SPS 동작 시 발전비용 증가를 경감 할 수 있다. Special Protection Scheme(SPS) for generator tripping action is an emergency control tool that secures the power system stability by instantly tripping the pre-determined number of generators to avoid the acceleration of the remaining generators in a large-scaled power plants when a fault occurs on the drawing transmission lines. However, since the existing operating conditions of SPS are set based on a peak demand, SPS could trip more generators than required if it is activated during the off-peak demand period. For this, this paper proposes the algorithm for setting the operating conditions of SPS through the online stability evaluation with the periodically updated operating conditions of power systems. The proposed algorithm adopts COA for the accuracy and speed of the stability evaluation, and can reduce the number of tripping generators by SPS during the off-peak demand period. This results in reducing the loss of profit caused by a fault on power systems

저온 프로세스에 의한 다결정 실리콘 박막 제작

이중휘(Lee, Jung-Hui),최병정(Choi, Byoung-Jung),주병윤(Chu, Byung-Yoon),양성채(Yang, Sung-Chae) 한국신재생에너지학회 2005 한국신재생에너지학회 학술대회논문집 Vol.2005 No.11