http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
2.5% C-15% Cr 성형탄 슬리이브 캐스팅로울의 열처리에 대한 온도 분포예측
하만영,윤영환 대한기계학회 1986 대한기계학회논문집 Vol.10 No.3
본 연구에서는 표면은 단단하고 내면은 강인한 조직을 얻기위하여 대형 성형 탄 로울에 대하여 노에서의 급속가열 및 대기 상태에서의 자연냉각의 열처리가 수행 되어진다. 급속가열 및 냉각시 성형탄 로울 내부의 온도 분포 예측을 위하여 대류 및 복사 열전달 경계조건을 가지는 1차원 비정상 열전도 방정식이 유한 차분법을 사 용하여 해석되어졌다. 여기서 급속가열시 연소가스로 부터 기체복사에 의하여 성 형탄 로울의 바깥표면을 통하여 흡수되는 열량은
화염의 총괄폭사 계수를 나타내는 급수계수 및 가중치의 계산
하만영,허병기 대한기계학회 1986 대한기계학회논문집 Vol.10 No.1
Using the sbsorption coefficients and the weighting factors of the gray gas, the total emissivities of C $O_{2}$- $H_{2}$O and C $O_{2}$- $H_{2}$O- transient species-soot gas mixtures can be expressed by the following equation, [a numerical formula] Where, $a_{i}$ and $K_{i}$ represent the weighting factor and the absorption coeffient of i-gray gas respectively; L is the pathlength of the gas. This equation is widely used for the analyses of the radiation heat transfer in the combustors of internal combustion engines and in the furnace of external combustion engines. In this work, a simple calculation model of the weighting factor and the absorption coeffient of the above equation was developed. The weighting factors and the absorption coefficients of combustion products were calculated by applying the model to various kinds of fossil fuels such as coal and heavy oil. Then, the computed total emissivities for each fuel and pathlength were compared with measured and calculated values which have been already published in the literatures. The followings were the results obtained through the comparisons between the calculated emissivites and the published values; the developed model for the calculations of the weighting factor and the absorption coefficient of C $O_{2}$- $H_{2}$O and C $O_{2}$- $H_{2}$O- transient species-soot gas mixtures could be applied over the wide ranges of the temperature and the pathlength; the errors between the total emissivities calculted and the values published were maximum 10%, and average 1%, respectively.
파울링 예측을 위한 가스-입자 이상 유동 해석(1)-고온 풍동 설계 및 성능실험-
하만영,이대래,Ha, Man-Yeong,Lee, Dae-Rae 대한기계학회 1996 大韓機械學會論文集B Vol.20 No.11
We designed the hot wind tunnel to reproduce the conditions of utility boiler and carried out its performance test, in order to investigate the particulate two-phase flow behaviour, the fouling and heat transfer characteristics to the heat exchanger. The hot wind tunnel introduces the control system to control the temperature in the test section. The particle is injected into the hot gas stream. The fouling probe (cylindrical tube) is positioned normal to the particulate gas-particle two-phase flow and cooled by the air. The temperature of gas and cooling air, and temperature in the fouling probe are measured as a function of time, giving the local and averaged heat transfer and fouling factor. The shape of particulate deposition adhered to the fouling probe is also observed.
진동하는 유동장하에서 내부 순환 유동을 고려한 액적의 증발에 관한 수치적 연구
하만영,Ha, Man-Yeong 대한기계학회 1996 大韓機械學會論文集B Vol.20 No.5
The two-dimensional, unsteady, laminar conservation equations for mass, momentum, energy and species transport in the gas phase and mass, momentum and energy in the liquid phase are solved simultaneously in spherical coordinates in order to study heating and vaporization of a droplet entrained in the oscillating flow. The numerical solution gives the velocity and temperature distribution in both gas and liquid phase as a function of time. When the gas flow oscillates around an vaporizing droplet, the liquid flow circulates in the clockwise or counterclockwise direction and the temperature distribution in the liquid phase changes its shapes, depending on the gas fow direction. When the gas flow changes its direction of circulating liquid flow is opposite to the gas flow, forming two vortex circulating in the opposite direction. During the heating period, the difference in the maximum and minimum temperature is large, followed by the almost uniform temperature slightly below the boiling temperature. The mass and heat transfer from the droplet depend on the droplet temperature, droplet diameter and the magnitude of relative velocity, giving the droplet lifetime different from the d$^{2}$-law.
쌍롤 연속 주조에서의 난류 유동, 온도 및 응고 예측을 위한 연구
하만영,최봉석,Ha, Man Yeong,Choi, Bong Seok 대한기계학회 1999 大韓機械學會論文集B Vol.23 No.1
A computer program has been developed for analyzing the two-dimensional, unsteady conservation equations for transport phenomena in the molten region of twin-roll continuous casting in order to predict the turbulent velocity, temperature fields, and solidification process of the molten steel. The energy equation of the cooling roll is solved simultaneously with the conservation equations of molten steel in order to consider heat transfer through the cooling roll. The results show the velocity, temperature and solidification pattern in the molten region with roll temperature as a function of time. The results for velocity and temperature fields with solidification are compared with those without solidification, giving different thermofluid characteristics in the molten region. We also investigated the effects of revolutional speed of roll, superheat and nozzle geometry on the turbulent flow, temperature and solidification in the molten steel and temperature fields in the cooling roll.