http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
Fe-(Mo,Mn)-P계 Lean alloy의 소결특성에 미치는 Si와 Sn의 영향
정우영,옥진욱,박동규,안인섭,Jung, Woo-Young,Ok, Jin-Uk,Park, Dong-Kyu,Ahn, In-Shup 한국분말야금학회 2018 한국분말재료학회지 (KPMI) Vol.25 No.4
A lean alloy is defined as a low alloy steel that minimizes the content of the alloying elements, while maintaining the characteristics of the sintered alloy. The purpose of this study is to determine the change in microstructure and mechanical properties due to the addition of silicon or tin in Fe-Mo-P, Fe-Mn-P, and Fe-Mo-Mn-P alloys. Silicon- or tin-added F-Mo-P, Fe-Mn-P, and Fe-Mo-Mn-P master alloys were compacted at 700 MPa and subsequently sintered under a $H_2-N_2$ atmosphere at $1120^{\circ}C$. The sintered density of three alloy systems decreases under the same compacting pressure due to dimensional expansion with increasing Si content. As the diffusion rate in the Fe-P-Mo system is higher than that in the Fe-P-Mn system, the decrease in the sintered density is the largest in the Fe-P-Mn system. The sintered density of Sn added alloys does not change with the increasing Sn content due to the effect of non-dimensional changes. However, the effect of Si addition on the transverse rupture strengthening enhancement is stronger than that of Sn addition in these lean alloys.
복합재료 트러스 교량시스템의 정적거동 및 파괴모드에 관한 해석적 연구
정우영,이형길,Jung, Woo-Young,Lee, Hyung-Kil 한국전산구조공학회 2007 한국전산구조공학회논문집 Vol.20 No.5
본 연구는 복합재료 교량시스템의 규준 정립을 위한 연구로서 실제 설계 시공되어진 복합재료 교량의 정밀해석수행과 이를 통한 복합재료 교량의 파괴거동 및 설계기준 등을 조사하는데 그 목적이 있다. 본 연구의 효율적인 연구를 위하여 실제 미국 NEW YORK주 내에 설계 시공되어있는 Noncomposite-FRP 복합재료 교량을 대상으로 해석적 연구를 수행하였으며 본 연구에서 사용된 해석적 모델을 토대로 실제 미국에서 기 수행되어진 교량 거동에 관한 해석 및 실험하중 평가와 그 결과를 비교하였다. 특히 국내 복합재료 교량의 해석적 설계기준 평가를 위하여 보다 실질적이고 정확한 파괴모드의 조사 및 분석이 요구되어지므로 본 연구에서는 이를 위하여 기존의 해석적 연구에서 가벼운 중량으로 인하여 무시되었던 자중의 영향과 각 적층 layer에 설계된 ply orientation을 고려하여 해석하였다. 그 결과 자중을 고려한 복합재료 패널들의 경우, 제작 결함에 따른 이음부 파괴가 없을 경우 교량 상부 구조 중 횡축 보에서의 국부 좌굴 파괴가 교량의 파괴를 지배할 것으로 본 연구결과에서 예측되었다. 이는 복합재료 교량 제작 시 복합재료 상판 패널과 보의 이음부가 Noncomposite로 제작되는 경우 실제 제작되어진 복합재료 상판의 고 강성에 의하여 재하 하중에 의한 하부 강재 거더 좌굴이 선행되는 것으로 판단된다. There is a concern with worldwide deterioration of highway bridges, particularly reinforced concrete. The advantages of fibre reinforced plastic(FRP) composites over conventional materials motivate their use in highway bridges for replacement of structures. Recently, an FRP deck has been installed on a state highway, located in New York State, as an experimental project. In this paper, a systematic approach for analysis of this FRP deck bridge is presented. Multi-step linear numerical analyses have been performed using the finite element method to study the structural behavior and the possible failure mechanism of the FRP deck-superstructure system. Deck's self-weight and ply orientations at the interface between steel girders and FRP deck are considered in this study. From this research, the results of the numerical analyses were corroborated with field test results. Analytical results reveal several potential failure mechanism for the FRP deck and truss bridge system. The results presented in this study may be used to propose engineering design guideline for new and replacement FRP bridge deck structure.
핵의학 영상 검사의 중장기 추세 분석 - 서울 소재 일개 상급 종합병원을 중심으로 -
정우영,심동오,최재민,Jung, Woo-Young,Shim, Dong-Oh,Choi, Jae-Min 대한핵의학기술학회 2019 핵의학 기술 Vol.23 No.1
핵의학은 1959년에 국내 도입되어 갑상선 기능 항진증의 치료를 위해 $^{131}I$을 경구 투여한 것으로 시작되었고, 감마카메라는 1969년에 국내 도입되어 핵의학 영상 검사를 시작한 후 지속적인 성장을 하고 있다. 서울 소재 일개 상급종합병원을 대상으로 1998년부터 2017년까지의 핵의학 영상 검사 및 치료 실적에 대해 중장기 추세를 분석하였다. 분석 도구로는 해당병원의 통계 프로그램을 이용하여 감마, PET, 골밀도, 치료로 구분하여 검사 실적 추세 및 상세 분석을 하였다. 이와 같은 실적을 바탕으로 미래 핵의학 발전에 대한 예측을 하고, 핵의학 발전 방향 및 발전 계획의 준거 틀을 마련하는데 그 목적이 있었다. 지난 20년 동안에 Bone scan, MUGA scan, Renal scan(99mTc-DTPA), $^{18}F$-FPCIT PET, 골밀도 검사 등이 상승 추세였고, Myocardium perfusion SPECT, Thyroid scan, Lung scan 등은 하락 추세였으며, Hepatobiliary scan, Renal scan(99mTc-DMSA), $^{18}F$-FDG PET 등은 정체되어 있었다. 그리고 핵의학 치료 실적은 2011년까지 상승 추세였으나 갑상선 과잉진료 논란이후에 급락한 후 회복하지 못하고 있었다. 또한 핵의학 영상 검사와 경쟁 검사 간의 건수를 분석한 결과, 반비례 관계이거나 역치 현상이 있었다. 핵의학 영상 검사 및 치료 실적은 의약 분업 도입과정에서 발생한 의사 파업(2000년), 갑상선 과잉 진료 논란(2011년, 2014년), 무증상 추적 검사를 제한한 PET 요양 급여 개정(2014년), 중동호흡기증후군 확산(2015년), 그리고 수시로 발생하는 요양 급여 삭감 등의 변수에 큰 영향을 받았다. 핵의학 영상 검사는 중장기 상승 추세에 있었으나 2012년 이후로 정체되어 있었다. 핵의학 영상검사 및 치료의 중장기 성장과 발전 방향을 위해서는 시시각각 변하는 의료 환경의 변화에 대한 적극적인 대응은 물론이고, 핵의학 영상 검사 및 치료가 타 경쟁 검사 및 치료에 대한 경쟁 우위 확보를 위한 노력, 신규 검사 및 치료의 개발, 임상적인 정량지표의 개발 및 안정적 유지에 대한 노력이 필요할 것으로 판단된다. Purpose Nuclear medicine was initially introduced in Korea in 1969 and widely applied to treat hyperthyroidism with $^{131}I$. Also, gamma camera was adopted in 1969 in the first place and its application has been growing continually in many ways. We analyzed long-term trend in nuclear medicine examinations for the last 2 decades. The purpose of this paper is to make predictions and to set both plans and directions on the development of nuclear medicine. Materials and Methods We analyzed the performance of nuclear medicine examinations and therapies performed in Asan Medical Center from 1998 to 2017. Results Results from the last 20 years regarding Bone scan, Renal scan, MUGA scan and $^{18}F$-FPCIT, Bone Mineral Density were on a increase. And Myocardium perfusion SPECT, Thyroid scan, Lung scan were on a decrease while $^{18}F-FDG$ PET maintained on a steady course. Until 2010 there was a positive performance with the therapy but after the excessive medical care in thyroid examination performance is at status quo. Key events such as a medical strike(2000), Middle-East Respiratory Syndrome (2015) influenced the overall performance of the therapy. Conclusion In order to promote a long-term growth in nuclear medicine examination and therapy, it is inevitable to respond to the changes in current medical environment. Furthermore, it is strongly suggested to put efforts to maintain and develop new examinations and clinical indicators.
총 계수 분석법과 평균 계수 분석법에 따른 신장 기능의 차이 분석
정우영,조시만,박승온,심동오,JUNG WOO-YOUNG,CHO SHEE-MAN,PARK SEUNG-YONG,SHIM DONG-OH 대한방사선사협회 2003 대한방사선사협회지 Vol.29 No.1
감마카메라를 이용하여 영상화할 수 있는 $^{99m}Tc-DMSA$ 신장 검사는 비침습적으로 신장의 기능과 형태를 동시에 평가할 수 있고, 신장 기능의 이상은 형태학적인 변화 보다 먼저 나타나기 때문에 다른 검사보다 $^{99m}Tc-DMSA$ 신장 검사를 이용하면 병변을 조기에 진단할 수 있는 장점이 있다. 신장의 상대적 기능 평가시에 깊이 보정, 총 계수 또는 평균 계수의 사용, BKG 보정, SPECT 검사의 Purpose : $^{99m}Tc-DMSA$ renal scan can be used in the evaluation of relative renal function and some anatomy. The relative renal function can be assess by measurement of $^{99m}Tc-DMSA$ uptake by the individual kidney. Renal counts
정우영,전병혁,박해웅,홍계원,김찬중,Jung, Woo-Young,Jun, Byung-Hyuk,Park, Hai-Woong,Hong, Gye-Won,Kim, Chan-Joong 한국초전도학회 2006 Progress in superconductivity Vol.8 No.1
[ $Yb_2O_3$ ] films were successfully deposited on a cube-textured Ni and(100) $SrTiO_3$(STO) single crystal substrates by metal organic chemical vapor deposition(MOCVD) method using $H_2O$ vapor as an oxidant. $H_2O$ vapor was used in order to avoid the oxidation of Ni substrate. The working pressure and Ar flow rate were 10 Ton and 600 sccm, respectively. $Yb_2O_3$ films on STO were formed at high temperatures above $900^{\circ}C$. While XRD peaks from $Yb_2O_3$ were hardly detected at $900^{\circ}C$, the $Yb_2O_3$(400) texture was developed fur the films grown at deposition temperatures above $950^{\circ}C$. The AEM surface roughness of $Yb_2O_3$ film, grown on STO, was in the range of $6{\sim}10nm$ for the film deposited at $950^{\circ}C$ with a $H_2O$ vapor partial pressure of 5.5 Ton and deposition times of 3 and 5 mins. For cube-textured Ni substrate, both $Yb_2O_3$(222) and $Yb_2O_3$ (400) textures were developed textures at deposition temperatures above $850^{\circ}C$.
Fe-(Mo-Mn-P)-xSi계 합금의 성형밀도에 따른 소결거동
정우영,옥진욱,박동규,안인섭,Jung, Woo-Young,Ok, Jin-Uk,Park, Dong-Kyu,Ahn, In-Shup 한국분말야금학회 2017 한국분말재료학회지 (KPMI) Vol.24 No.5
The addition of a large amount of alloying elements reduces the compactibility and increases the compacting pressure, thereby shortening the life of the compacting die and increasing the process cost of commercial PM steel. In this study, the characteristic changes of Fe-Mo-P, Fe-Mn-P, and Fe-Mo-Mn-P alloys are investigated according to the Si contents to replace the expensive elements, such as Ni. All compacts with different Si contents are fabricated with the same green densities of 7.0 and $7.2g/cm^3$. The transverse rupture strength (TRS) and sintered density are measured using the specimens obtained through the sintering process. The sintered density tends to decrease, whereas the TRS increases as the Si content increases. The TRS of the sintered specimen compacted with $7.2g/cm^3$ is twice as high as that compacted with $7.0g/cm^3$.
상용프로그램용 Subroutine 부착모델을 이용한 동결융해에 의한 FRP-콘크리트 부착-슬립 거동에 대한 해석적 평가
정우영,김남정,Jung. Woo Young,Kim. Nam Jung 한국방재학회 2012 한국방재학회논문집 Vol.12 No.1
본 연구는 FRP 휨 부착 보강공법을 적용한 콘크리트 구조물에 대하여 부착경계면의 동결융해에 의한 장기부착특성과 이들 부착에 따른 전체구조물의 거동을 조사하기 위한 해석적 연구로서 기존 연구에서 제안된 여러 가지 비선형 부착-슬립 거동특성을 바탕으로 수치해석용 비선형 부착-슬립 Subroutine을 제안하였다. 제안된 상용해석용 수치모델의 타당성 검증을 위하여 기존 검증된 역학적 모델식에서 산출된 값들과 그 결과를 비교하였으며 이를 통하여 실제 부착구조물에 휨 보강부착 시 전체구조물의 구조해석 및 거동평가를 수행하였다. 본 연구의 해석결과에서 제시된 동결융해에 따른 부착경계면의 거동의 경우 부착면의 부착력 저하로 인하여 최대부착응력과 FRP 표면응력이 점차적으로 감소함을 알 수 있었고 이로 인한 허용부착하중 또한 감소하는 것으로 예측되었다. 이는 동결융해에 따른 보강효과 감소를 의미하는 것으로서 향후 보다 정확한 거동분석을 위한 실험적 연구와 병행하여 수행될 필요성이 있을 것으로 판단된다. This research presents an analytical evaluation of the long-term bonding behavior at the interface between concrete and FRP under freeze-thaw environments and overall structural performance in the RC structure reinforced by FRP. To predict overall structural performance of the structure, a nonlinear bond-slip subroutine is proposed and verified for its availability with comparison of the previous experimental results. Finally, analytical results indicate that the maximum stress of the interface and the surface stress on the FRP skin plate were reduced gradually under freeze-thaw environments. It is evidence that the bonding capacity at the interface between concrete and FRP may be decreased as the exposure for the freeze-thaw environments is increased. To make more accurate results, more advanced works for analytical subroutine are performed and experimental results will be compared and discussed in the future.
철근부식 팽창 및 비부착 구간에 따른 RC 부재의 휨 성능 평가
정우영,백상훈,연종호,Jung,Woo-Young,Beak,Sang-Hoon,Yeon,Jong-Ho 한국방재학회 2008 한국방재학회논문집 Vol.8 No.5
본 논문은 염해에 의한 부착성능 저하에 따른 철근-콘크리트 국부 비부착 구간 변화에 따른 보의 휨 실험 및 해석적 연구이다. RC보의 휨 실험 및 해석적 연구를 통하여 부착강도 및 부식정도에 대한 휨 강성을 평가, 분석하였다. 철근부식에 따른 국부적 부착손상 구간을 표현하기위하여 본 연구에서는 고무호스를 이용한 비부착 구간 모사 시험체를 제작, 염해에 의한 철근콘크리트 보의 국부 부식구간을 표현하였고 이에 대한 휨 성능을 평가하였다. 해석적 연구에서는 상용해석프로그램을 이용한 성능평가와 균열해석을 수행하여 국부적 부착구간 변화에 따른 균열 폭, 균열깊이, 위치를 파악함으로써 실제 실험결과와의 균열 확산을 예측, 비교하였다. 본 연구의 부식정도 및 국부적 비부착 구간 확대에 따른 실험적, 해석적 철근부식-강성변화율은 향후 노후 철근콘크리트 구조물의 국부적 손상 모델의 개발 및 평가에 있어 기초자료로 활용될 수 있을 것이다. This paper presents experimental and analysis studies about both the corroded steel expansion and the variation of poor bonding range between steel and concrete. A loss of overall bonding capacity at the concrete-steel interface is evaluated experimentally and crack patterns at the bottom of the concrete are presented here. Steel-concrete interface is covered by rubber due to present local loss of the concrete-steel interface bonding capacity. In case of crack analysis performed by commercial FEM programs. we investigated crack‘s pattern and location. Finally, it is concluded that overall flexural capacity of the reinforced concrete structure is increased by the corroded steel expansion and is dependent of the bonding range at the steel- concrete interface. These results give an important factor to decide a life of reinforced concrete structures.
철근부식 및 부착성능 변화에 따른 압축 및 휨 부재의 거동
정우영,권민호,안미경,Jung. Woo-Young,Kwon. Min-Ho,Ahn. Mi-Kyoung 한국방재학회 2011 한국방재학회논문집 Vol.11 No.5
본 연구는 염해의 영향을 받은 철근콘크리트 구조물의 성능평가에 관한 연구로서 철근부식에 따른 압축, 휨 부재의 거동을 실험적으로 평가하였다. 철근부식에 따른 유효단면적 변화에 의한 성능평가를 고려한 시험체의 경우 본 연구에서는 전위차 촉진법을 이용하였으며 장기간 발생된 과도한 부식작용으로 인하여 야기되는 철근-콘크리트 경계면 내 부착성능 저하 시험체의 경우 얇은두께의 압축고무 수축튜브를 이용하여 철근길이 대비 비부착 비율을 토대로 경계면 국부 비부착 시험체를 제작, 실험하였다. 두 조건의 시험체들에 대한 실험 결과, 압축부재의 경우 거동메커니즘의 특성을 고려할 때 철근부식에 경계면 부착성능 저하에 따른 큰 성능변화는 발생하지 않았으나 과도한 부식이 진행된 경우 철근유효단면적 변화 및 철근 이형부의 마찰력 저하에 의하여 구조물의 압축성능이 다소 감소하였다. 반면, 휨 부재의 경우 철근부식에 따른 거동결과 차이가 상대적으로 크게 발생하였는데 철근-콘크리트 부착성능 변화에 따른 휨 부재의 거동은 초기철근부식(2%)상태를 제외하고 부식이 진행됨에 따라 구조물 내 극심한 균열 및 초기 취성파괴를 나타내었다. This research presents an experimental study on the load capacity of reinforced concrete(RC) compression and flexural members induced by chloride corrosion. The parameters considered in this study are both the increased corrosion ratios of reinforcing bar and the variation of partial corroded length. Some test specimens are corroded by using Accelerated Potentiometeric Corrosion Method and the others which are fabricated by using compressive rubber tubes at the contact surface between concrete and steel bar are tested in order to investigate the load capacity of the structure in the events of the degradation of bonding strength at the interface between concrete and steel bar. It is finally shown that the overall load capacity of compression member with corroded reinforcing bars is decreased because it is mainly influenced by not the bonding strength at the concrete-steel contact surface but the reduction of the effective section area at the corroded reinforcing bar; while for the flexural members, compared to the compression member, the degradation of load capacity is remarkable. It is evident that the flexural member is influenced by both two parameters like the effective area and bonding strength at the contact surface except initial corrosion ratio 2%. The reduction of the load capacity of this member leads to occur severe crack and prematured failure after yielding the member.
역할 모델(Role model)을 이용한 업무 개선 - 업무의 달인(達人)을 찾아라 -
정우영,류재광,김경식,Jung, Woo-Young,Ryu, Jae-Kwang,Kim, Kyung-Sik 대한핵의학기술학회 2008 핵의학 기술 Vol.12 No.3
목적 : 역할 모델링의 목적은 효율적(빠르고, 쉽고, 정확 하게)으로 업무를 수행하는 업무의 달인(達人)을 찾아 이를 모델로 하여 실무자들이 효과적으로 각자 맡은바 업무를 수행 할 수 있도록 하기 위한 과정이다. 이러한 과정은 실무자들 간의 업무 능력의 편차를 발견하고 역할 모델을 제시하여 실무에 최적화된 업무 프로세스를 정착하기 위한 노력이며 이는 업무 기술 기준의 표준화 작업이라고 할 수 있다. 실험재료 및 방법 : 서울아산병원 핵의학과는 6~7개의 역할 모델링 항목을 개발하였고, 실무에 적용하여 관리하고 있다. 이 중에서 첫째, Bone scan 검사 시에 발목 고정의 중요성 인식 및 고정의 효율 향상과 둘째, Bone scan 검사에서 시작 지점과 종료 지점의 표준화를 통한 업무 개선 사례를 보고한다. 결과 : 두 가지의 사례 모두에서 개선 전에 비하여 개선 후에 업무 효율을 향상할 수 있었다. 결론 : 역할 모델링(Role modeling)의 실무 활용은 궁극적으로 성공적인 업무 수행자 또는 우수한 집단들의 행동 및 업무를 과학적으로 분석하여 탁월한 역할 모델을 발굴하고 이를 업무 기술 기준 표준화에 적극 활용하여 직원들 간의 업무능력의 편차를 줄이는데 그 목적이 있다. 즉, 담당 업무를 효과적으로 잘 처리하는 직원을 모델로 하여, 업무를 열심히 수행함에도 불구하고 그 성과가 부족한 직원의 성과 향상을 꾀하는 것이 주된 목적이라 하겠다. 핵의학팀은 역할 모델링 항목을 지속적으로 개발하고 실무에 활용하여 업무를 개선해 나아갈 계획이며 업무 개선 활동에 유용하게 사용할 수 있는 도구로 평가하고 있다. Purpose: The purpose of a role model is to find a master or expert who conduct their business effectively and work as a model that helps staff in charge to conduct their works effectively. This process is an effort to find out the deviation of work performance capability among staffs in charge and settle the work process to be optimized to practical business, the standardization of protocol. Materials and Methods: Seoul Asan medical center nuclear department developed 6~7 role modeling items and has applied it to work. I report two operation improvement cases we had applied a role model to Seoul ASAN medical center. Result: By comparison with none application of a role model, we could improve operation efficiency. Conclusion: The main purpose of role modeling is to make the employees who do the business in their charge effectively as a role model and contribute to work performance of employees who are lack of work performance although they performed their works hard. Our team is going to develop role model items continuously and to make a use of it to practical work then improve work performance. We regard it as a useful tool to performance improvement. The performance improvement by using a role model was very useful instrument.